Sharp EL1750PIII - Printing Calculator,... User manual

EL-1750P III
ELECTRONIC PRINTING CALCULATOR
DRUCKENDER TISCHRECHNER
CALCULATRICE IMPRIMANTE ÉLECTRONIQUE
CALCULADORA IMPRESORA ELECTRÓNICA
CALCOLATRICE ELETTRONICA STAMPANTE
ELEKTRONISK SKRIVANDE OCH VISANDE RÄKNARE
ELEKTRONISCHE REKENMACHINE MET AFDRUK
CALCULADORA ELETRÔNICA COM IMPRESSORA
NAUHALASKIN
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUAL DE MANEJO
MANUALE DI ISTRUZIONI
BRUKSANVISNING
GEBRUIKSAANWIJZING
MANUAL DE INSTRUÇÕES
KÄYTTÖOHJE
ENGLISH ............................................................... Page 2
CALCULATION EXAMPLES ................................. Page 135
DEUTSCH .............................................................. Seite 16
RECHNUNGSBEISPIELE ..................................... Seite 135
FRANÇAIS ............................................................. Page 31
EXEMPLES DE CALCULS .................................... Page 136
ESPAÑOL .............................................................. Página 46
EJEMPLOS DE CÁLCULOS ................................. Página 137
ITALIANO .............................................................. Pagina 61
ESEMPI DI CALCOLO ........................................... Pagina 137
SVENSKA .............................................................. Sida 76
RÄKNEEXEMPEL .................................................. Sida 138
NEDERLANDS ...................................................... Pagina 90
REKENVOORBEELDEN ....................................... Pagina 138
PORTUGUÊS ........................................................ Página 105
EXEMPLOS DE CÁLCULOS ................................. Página 139
SUOMI ................................................................... Sivu 120
LASKENTAESIMERKKEJÄ ................................... Sivu 139
EL-1750PIII(LCO)-Cover-1 04.9.1, 9:28 AM1

Notes for handling Lithium batteries:
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
Hinweise zur Handhabung von Lithium-Batterien:
VORSICHT
Bei Verwendung einer uneeigneten Ersatzbatterie besteht
Explosionsgefahr.
Nur durch den gleichen oder einen vom Hersteller empfohlenen
gleichwertigen Typ ersetzen.
Verbrauchte Batterien gemäß Herstelleranleitung entsorgen.
Remarques sur la manipulation des piles au lithium:
ATTENTION
Danger d’explosion de la pile si elle n’est pas remplacée correctement.
Remplacez-la uniquement par le même type de pile ou un type
équivalent recommandé par le fabricant.
Débarrassez-vous des piles usagers en respectant les instructions du
fabricant.
Notas para el manejo de las baterías de litio:
PRECAUCIÓN
Peligro de explosión si reemplaza incorrectamente la batería.
Reemplácela por otra igual o de tipo equivalente recomendada por el
fabricante.
Deshágase de las baterías de acuerdo con las instrucciones del
fabricante.
Note concernenti le batterie al litio:
AVVERTENZA
Se la batteria non viene sostituita in modo corretto c’è pericolo di
esplosioni.
Sostituire la batteria con una dello stesso tipo o con una equivalente
raccomandata dalla fabbrica.
Smaltire le batterie usate seguendo le istruzioni della fabbrica.
Observera om hantering av litiumbatterier:
OBSERVERA!
Felaktigt batteribyte medför risk för explosion.
Byt endast ut batteriet mot ett batteri av samma eller motsvarande typ
rekommenderat av tillverkaren.
Kassera ett förbrukat batteri enligt tillverkarens anvisningar.
Opmerkingen betreffende de behandeling van lithiumbatterijen:
LET OP
Ontploffingsgevaar indien de batterij verkeerd wordt aangebracht.
Vervang uitsluitend door een batterij van hetzelfde of een gelijkwaardig
type, aanbevolen door de fabrikant.
Gooi gebruikte batterijen weg overeenkomstig de instructies van de
fabrikant.
Notas para o manuseio de pilhas de lítio:
PRECAUÇÃO
Existe o perigo de explosão se a pilha for trocada incorretamente.
Troque apenas com o mesmo tipo ou equivalente recomendado pelo
fabricante.
Descarte-se das pilhas usadas de acordo com as instruções do
fabricante.
Huomautuksia litiumparistojen käsittelystä:
HUOMAUTUS
Räjähdysvaara, jos paristo vaihdetaan väärin.
Paristo tulee vaihtaa vain samaniaiseen tai valmistajan suosittelemaan
vastaavaan tyyppiin.
Hävitä käytetyt paristot valmistajan antamien ohjeiden mukaisesti.
EL-1750PIII(LCO)-Semko 04.9.1, 9:28 AM2

2
CONTENTS
ENGLISH
Page
• USING THE CALCULATOR FOR THE
FIRST TIME ........................................................... 3
• OPERATING CONTROLS ..................................... 4
• INK ROLLER REPLACEMENT ............................. 8
• PAPER ROLL REPLACEMENT ............................. 9
• BATTERY REPLACEMENT ................................. 10
• HOW TO CONNECT THE AC ADAPTOR
(OPTION) ............................................................. 11
• ERRORS .............................................................. 12
• REPLACEMENT OF BATTERY FOR
MEMORY PROTECTION .................................... 12
• SPECIFICATIONS ............................................... 14
• RESETTING THE UNIT ....................................... 15
• CALCULATION EXAMPLES .............................. 135
To insure trouble-free operation of your SHARP
calculator, we recommend the following:
1. The calculator should be kept in areas free from
extreme temperature changes, moisture, and dust.
2. A soft, dry cloth should be used to clean the
calculator. Do not use solvents or a wet cloth.
3. Since this product is not waterproof, do not use it or
store it where fluids, for example water, can splash
onto it. Raindrops, water spray, juice, coffee,
steam, perspiration, etc. will also cause malfunction.
4. If service should be required, use only a SHARP
servicing dealer, a SHARP approved service facility
or SHARP repair service.
SHARP will not be liable nor responsible for any
incidental or consequential economic or property
damage caused by misuse and/or malfunctions of
this product and its peripherals, unless such
liability is acknowledged by law.
OPERATIONAL NOTES
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM2

3
USING THE CALCULATOR FOR THE FIRST TIME
First, pull out the insulation sheet for the memory
protection battery (installed for retaining the date/
time/tax rate information). Reset the calculator to
initialize the unit's state, then adjust the date and
time before using the calculator.
Removing the insulation sheet, and resetting
1. Pull out the insulation sheet for the memory
protection battery.
2. Press the RESET switch located on the back of the
unit.
(See “RESETTING THE UNIT”.)
* The clock starts from 00:00:00 a.m. on 1 January
2005.
Adjusting date and time
Example: In the case of 3:38 p.m. on 15 September
2004
* When the adjustment is complete, the clock starts at
3:38:00 p.m.
15 9 2004 15. 09. 2004
15 38 15-38 00
0.
(see “GRAND TOTAL / RATE SETTING MODE
SELECTOR”)
Operation Display
GT • RATE
SET
EL-1750PIII(LCO)-Eng 04.9.16, 11:11 AM3

4
OFF •P P•IC ON
POWER SWITCH; PRINT / ITEM
COUNT MODE SELECTOR:
“OFF”: Power OFF
“•”: Power ON. Set to the non print mode.
“P”: Power ON. Set to the print mode.
“P•IC”: Power ON. Set to the print and item count
mode.
1) For addition or subtraction, each time
is pressed, 1 is added to the item
counter, and each time is pressed, 1
is subtracted.
•The count is printed when the calcu-
lated result is obtained.
•Pressing of , clears the
counter.
2) When the grand total/rate setting mode
selector is in the ON position (GT), the
counter will count the number of times
that the calculation results have been
stored in the grand total memory. To print
and clear the count, press the key.
3) The memory item counter will count the
number of times that the key has
been pressed in the addition.
OPERATING CONTROLS Note: •Each time the key is used in
the subtraction, 1 will be subtracted
from the count.
•The count is printed when the
memory is recalled.
•Pressing of the key clears the
counter.
Note: The counter has a maximum capacity of 3
digits (up to ±999). If the count exceeds the
maximum, the counter will recount from zero.
ROUNDING SELECTOR:
Example: Set Decimal Selector to 2.
4 ÷9 = 0.444 ... , 5 ÷9 = 0.555 ...
Note: The decimal point floats during successive
calculation by the use of or .
If the decimal selector is set to “F”then the answer is
always rounded down ( ).
4 9 5 9
0.45 0.56
5/4 0.44 0.56
0.44 0.55
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM4

5
GT • RATE
SET
GRAND TOTAL / RATE SETTING MODE
SELECTOR:
“GT”: Grand Total
“•”: Neutral
“RATE SET”: To set the date, time, and tax rate, set
this switch at the “RATE SET”
position.
Date:
•Enter in the order of day, month, and year, then
press to complete the entry.
•Use to separate day, month, and year.
•When is pressed, the number entered is
evaluated and displayed as “date”if the value is
within the following range; “Error”is displayed
otherwise, and the previously set date is restored.
Day: 1 - 31; Month: 1 - 12; Year: 2000 - 2099 (in 4
digits) or 00 - 99 (in 2 digits)
Time:
•Enter in the order of hour, minutes, then press
to complete the entry.
(There is no entry available for the seconds value.
The clock starts at zero second.)
•If the hour/minute digit is less than 10, it is not
necessary to enter the first digit “0”.
•Use to separate hour and minute values.
•When is pressed, the number entered is
evaluated and displayed as “time”if the value is
within the following range; “Error”is displayed
otherwise, and the previously set time is restored.
Hour: 0 - 23 (24-hour system for the hour entry),
Minute: 0 - 59
Tax rate:
•Press three times, enter the tax rate, followed
by .
•A maximum of 4 digits can be stored (decimal point
is not counted as a digit).
•Only one rate can be stored. If you enter a new rate,
the previous rate will be cleared.
F20A
3
DECIMAL / ADD MODE SELECTOR:
“3 2 0”: Presets the number of decimal places in the
answer.
“F”: The answer is displayed in the floating decimal
system.
“A”: The decimal point in addition and subtraction
entries is automatically positioned to the 2nd
digit from the lowest digit of entry number. Use
of the add mode permits addition and subtrac-
tion of numbers without entry of the decimal
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM5

6
point. Use of , and will automatically
override the add mode and decimally correct
answers will be printed.
CLOCK / CALENDAR KEY:
•Each time this key is pressed, the mode
switches.
Calculation mode →Date display mode →
Clock display mode →Calculation mode
•Use this key also to adjust date and time
(see “GRAND TOTAL / RATE SETTING
MODE SELECTOR”).
PAPER FEED KEY
LAST DIGIT CORRECTION KEY
NON-ADD / SUBTOTAL KEY:
Non-add –When this key is pressed right after
an entry of a number in the Print mode, the
entry is printed on the left-hand side with the
symbol “#”. This key is used to print out
numbers not subjects to calculation such as
code, date, etc.
Subtotal –Used to get subtotal(s) of additions
and/or subtractions. When pressed following
the or key, the subtotal is printed with
the symbol “
◊ ”and the calculation may be
continued.
By pressing this key even in the Non-print
mode, the displayed number is printed
without any symbol.
•When the POWER SWITCH; PRINT / ITEM
COUNT MODE SELECTOR is set “•”, “P”or
“P•IC”position, and Date or Clock is
displayed, press this key to print the
displayed contents, including “#”symbol,
from the left side of the paper roll.
Example:
Date printing
#15 •09 •2004 ••••••
(In the case of 15 September 2004)
Clock printing
#10 •30 •••••••••••
(when the time is 10:30 a.m.)
#18 •25 •••••••••••
(when the time is 6:25 p.m.)
•When the Date / Clock printing is complete,
the Calculation mode is restored.
CLEAR / CLEAR ENTRY KEY
Press this key twice, followed by , to print
the set tax rate.
TOTAL KEY
EQUAL KEY
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM6

7
CHANGE SIGN KEY:
Changes the algebraic sign of a number (i.e.,
positive to negative or negative to positive).
RECALL AND CLEAR MEMORY KEY
RECALL MEMORY KEY
TAX-INCLUDING KEY
PRE-TAX KEY
AVERAGE KEY:
Used to calculate the average.
GRAND TOTAL KEY
COST PRICE ENTRY KEY:
Press this key to enter the cost price.
SELLING PRICE ENTRY KEY:
Press this key to enter the selling price.
MARGIN ENTRY KEY:
Press this key to enter the margin.
DISPLAY SYMBOLS:
M:Appears when a number is in the memory.
–:Appears when a number is negative.
G:Appears when a number is in the grand total
memory.
E:Appears when an overflow or other error is
detected.
TAX+ : Appears when the total calculated includes
tax.
TAX– : Appears when the total calculated excludes
tax.
TAX : Appears when the tax rate is set.
* Although all available symbols are shown here for
instruction purposes, these symbols will not appear
on the screen simultaneously.
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM7

8
INK ROLLER REPLACEMENT
If printing is blurry even when the ink roller is in the
proper position, replace the roller.
Ink roller: Type EA-772R
WARNING
APPLYING INK TO WORN INK ROLLER OR USE
OF UNAPPROVED INK ROLLER MAY CAUSE
SERIOUS DAMAGE TO PRINTER.
1) Set the power switch to OFF.
2) Remove the printer cover. (Fig. 1)
3) Hold the top of the ink roller and remove the roller
by pulling it toward you and then upward. (Fig. 2)
4) Install the new ink roller in the correct position.
Make sure that the roller is securely in place. (Fig.
3)
5) Put back the printer cover.
Cleaning the printing mechanism
If the print becomes dull after long time usage,
clean the printing wheel according to the
following procedures:
1) Remove the printer cover and the ink roller.
2) Install the paper roll and feed it until it comes out of
the front of the printing mechanism.
3) Put a small brush (like a tooth brush) lightly to the
printing wheel and clean it by pressing .
4) Put back the ink roller and the printer cover.
Note: •Do not rotate the printing mechanism manu-
ally, this may damage the printer.
Fig. 1
Fig. 2 Fig. 3
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM8

9
Never insert paper roll if torn. Doing so will
cause paper to jam.
Always cut leading edge with scissors first.
1) Insert the leading edge of the paper roll into the
opening. (Fig. 1)
2) Turn the power on and feed the paper by pressing
. (Fig. 2)
3) Lift the attached metal paper holder up and insert
the paper roll to the paper holder. (Fig. 3)
PAPER ROLL REPLACEMENT
Fig. 1
Fig. 2
Fig. 3
DO NOT PULL PAPER BACKWARDS AS THIS
MAY CAUSE DAMAGE TO PRINTING
MECHANISM.
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM9

10
To Install or Replace Batteries — When the battery
power becomes weak, printing may be halted, and
displayed images may disappear. If such symptoms
are observed, replace the batteries with new ones.
1. Set the power switch to OFF.
2. Remove the battery cover by sliding it in the
direction of the arrow on the cover.
3. Replace the batteries. Be sure that the “+”and “–”
marks on the battery correspond to the “+”and “–”
marks in the calculator. Always put back the 4
batteries at the same time.
4. Put back the battery cover.
Battery: Manganese dry battery, size AA (or R6) ×
4
BATTERY REPLACEMENT •If the leaked electrolyte gets into eyes, wash off
with clean water, and consult your doctor
immediately.
•If the leaked electrolyte gets on your skin or
clothes, wash off thoroughly with water.
•Remove batteries if not used for prolonged
periods of time.
•Do not leave dead batteries in the unit.
•Do not mix new and used batteries and/or
battery types.
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM10

12
There are several situations which will cause an
overflow or an error condition. When this occurs, “E”
will be displayed. The contents of the memory at the
time of the error are retained.
If an “E 0.”is displayed at the time of the error, “– ––
––––” will be printed in red and must be used
to clear the calculator.
Also, in rare cases, printing may stop midway and
the indication “E”appear on the display. This is not a
malfunction but is caused when the calculator is
exposed to strong electromagnetic noise or static
electricity from an external source. Should this occur,
press the key and then repeat the calculation
from the beginning.
Error conditions:
1. When the integer portion of an answer exceeds 12
digits.
2. When the integer portion of the contents of the
memory or grand total memory exceeds 12 digits.
(Ex. 999999999999 1 )
3. When any number is divided by zero. (Ex. 5 0
)
ERRORS
Time for battery replacement
Life of the memory protection battery is
approximately 2,500 hours at 25°C(77°F) with no
operation battery installed, and the AC adaptor not
connected.
* When the memory protection battery is weak, the
date/time setting is initialised (1/1/2005, 12:00:00
a.m.).
Verify the date/time setting in the date/clock display
mode after replacing the operation battery or when
connecting the AC adaptor with no operation battery
installed.
If the date/time setting is modified or incorrect,
promptly replace the memory protection battery with
new one.
(The life of the pre-installed battery may be shorter
than expected because of the time the calculator
spends during shipment.)
Method of battery replacement
Use one lithium battery (CR2032).
Caution: Replacing the battery will clear the date
and time settings, and the stored tax rate.
REPLACEMENT OF BATTERY FOR MEMORY PROTECTION
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM12

13
1) Set the power switch to the “OFF”position, and
disconnect the AC adaptor.
2) Remove the battery cover on the back of the unit.
(Fig. 1)
3) Remove the exhausted battery and install one
new lithium battery. Wipe the battery well with a dry
cloth and place the plus “+”side upward. (Fig. 2)
4) Replace the battery cover by reversing the removal
procedure.
5) Press the RESET switch on the back of the unit
(See “RESETTING THE UNIT”).
Fig. 1 Fig. 2
After battery replacement
•Connect the AC adaptor, and set the power switch to
the “ON”position.
Check that “0.”is displayed. If “0.”is not displayed,
remove the battery, reinstall it, and check the
display again.
•Readjust date, time, and tax rate settings.
•On the battery replacement date label found on the
back of the unit, write down the month and year
when the battery is replaced, as a reference for the
next battery replacement.
Precautions on battery use
•Do not leave an exhausted battery in the equipment.
•Do not expose the battery to water or flame, and do
not take it apart.
•Store batteries out of the reach of small children.
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM13

14
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
SPECIFICATIONS
Operating capacity: 12 digits
Power supply: Operating:
6V (DC): Manganese dry
battery, size AA (or R6) ×4
AC: Local voltage with AC
adaptor EA-28A (Option)
Memory backup:
3V (DC): (Lithium battery
CR2032 ×1)
Memory Protection Battery lifespan:
About 2,500 hours (While at
25°C (77°F), no operating
battery is installed, and the
AC adaptor is not connected.)
CLOCK SECTION
Accuracy: Within ±60 seconds per month
average (at 25°C (77°F))
Items to be displayed: Day, month, year, hour,
minute, second
Items to be printed: Day, month, year, hour, minute
Time system: 24-hour
PRINTING SECTION
Printer: Mechanical printer
Printing speed: Approx. 2 lines/sec.
(At temperature 25°C (77°F),
when “741•9 + ”is printed. An
AC adaptor EA-28A is used.
The printing speed will vary
with the number of rows and
the figure types to be printed.)
Printing paper: 57mm (2-1/4") –58mm (2-9/
32") wide
80mm (3-5/32") in diameter
(max.)
Operating temperature: 0°C –40°C (32°F –104°F)
Power consumption: 6V (DC): 1.8 W
Operating time: Manganese dry battery, size
AA (or R6)
Approx. 4,500 hours (in non-
print mode, displaying
555’555 at 25°C (77°F)
ambient temperature)
Operating time depends on
the type of battery and type of
use.
Dimensions: 150 mm (W) ×230 mm (D) ×
51.5 mm (H)
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM14

15
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
0 1 2 3 4 5 6 7 8 9 . ,
(5-29/32" (W) ×9-1/16" (D) ×
2-1/32" (H))
Weight: Approx. 530 g (1.17 Ib.) (with
batteries)
Accessories: 1 lithium battery(installed), 1
battery replacement date label
(attached on the unit’s back
body), 1 paper roll, 1 ink roller
(installed), manganese dry
battery ×4 and operation
manual
RESETTING THE UNIT
Strong impacts, exposure to electrical fields, or other
unusual conditions may render the unit inoperative,
and pressing the keys will have no effect. If this
occurs, you will have to press the RESET switch on
the bottom of the unit. The RESET switch should be
pressed only when:
•an abnormal event occurs and all keys are disabled.
Notes:
•Pressing the RESET switch will clear the date and
time settings, the tax rate setting, and the contents
of memory.
•Use only a ballpoint pen to press the RESET switch.
Do not use anything breakable or anything with a
sharp tip, such as a needle.
•After the RESET switch is pressed, connect the AC
adaptor. Turn the power switch “ON”and check that
“0.”is displayed.
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM15

16
INHALT
DEUTSCH
Seite
• ERSTE VERWENDUNG DES RECHNERS........ 17
• BETRIEBSTASTEN ............................................. 18
• ERSETZEN DER FARBROLLE ........................... 22
• ERSETZEN DER PAPIERROLLE ....................... 24
• AUSWECHSELN DER BATTERIEN ................... 25
• ANSCHLUSS DES NETZADAPTERS
(SONDERZUBEHÖR) .......................................... 26
• FEHLER ............................................................... 27
• AUSWECHSELN DER
SPEICHERSICHERUNGS-BATTERIE ................ 27
• TECHNISCHE DATEN ......................................... 29
• RÜCKSTELLEN DES GERÄTES ........................ 30
• BERECHNUNGSBEISPIELE ............................ 135
Um den störungsfreien Betrieb dieses Rechners von
SHARP zu gewährleisten, empfehlen wir folgende
Maßnahmen:
1. Verwenden Sie den Rechner nicht an Orten, an denen
große Temperaturunterschiede, hohe Luftfeuchtigkeit
oder Staub vorhanden ist.
2. Verwenden Sie ein weiches, trockenes Tuch zum
Reinigen des Rechners. Keine Lösungsmittel oder ein
feuchtes Tuch verwenden.
3. Da dieses Gerät nicht wasserbeständig ist, sollte es
nicht an Orten verwendet werden, an denen
Flüssigkeiten wie Wasser auf dem Gerät verschüttet
werden können. Wassertropfen, Wasserspray, Saft,
Kaffee, Dampf, Schweiß usw. können Fehlfunktionen
verursachen.
4. Wenn eine Reparatur notwendig ist, beauftragen Sie
nur einen SHARP-Händler, einen von SHARP
zugelassenen Kundendienst oder einen SHARP-
Reparaturdienst.
SHARP übernimmt keine Verantwortung oder Haftung
für irgendwelche zufälligen oder aus der Verwendung
folgenden wirtschaftlichen oder sachlichen Schäden,
die aufgrund der falschen Verwendung bzw. durch
Fehlfunktionen dieses Gerätes und dessen Zubehör
auftreten, ausgenommen diese Haftung ist gesetzlich
festgelegt.
BEDIENUNGSHINWEISE
EL-1750PIII(LCO)-Ger 04.9.15, 3:34 PM16

17
ERSTE VERWENDUNG DES RECHNERS
Zuerst das Isolierblatt zum Schutz der
Speichersicherungs-Batterie entfernen (dient zum
Speichern der Informationen von Datum/Uhrzeit/
Informationen zur Steuerrate). Den Rechner
zurückstellen um das Gerät zu initialisieren und dann
vor der Verwendung das Datum und die Uhrzeit
eingeben.
Entfernen des Isolierblattes und Rückstellung
1. Das Isolierblatt der Speichersicherungs-Batterie
herausziehen.
2. Den Rückstellschalter RESET auf der
Geräteunterseite drücken.
(Siehe “RÜCKSTELLEN DES GERÄTES”.)
*Die Uhr nimmt am 1. Januar 2005 um 00:00:00
Uhr ihren Betrieb auf.
Einstellung von Datum und Uhrzeit
Beispiel: Wenn das Datum der 15. September 2004
und die Uhrzeit 15:38 ist.
* Nach der Einstellung beginnt die Uhr bei 15:38:00.
15 9 2004 15. 09. 2004
15 38 15-38 00
0.
(Siehe “WAHLSCHALTER FÜR GESAMTSUMME/
EINSTELLUNG DER RATE”.)
Vorgang Anzeige
GT • RATE
SET
EL-1750PIII(LCO)-Ger 04.9.16, 11:11 AM17

18
OFF •P P•IC ON
BETRIEBSTASTE; WAHLSCHALTER
FÜR DRUCKEN / POSTENZÄHLER:
“OFF”: Ausschalten.
“•”: Einschalten. Einstellung der Betriebsart
ohne Ausdruck.
“P”: Einschalten. Einstellung der Betriebsart für
Ausdruck.
“P•IC”: Einschalten. Einstellung auf Ausdruck und
Betriebsart für Postenzähler.
1) Bei Additionen und Subtraktionen wird
jedesmal beim Drücken von eine
Eins zum Postenzähler hinzugefügt und
jedesmal beim Drücken von eine
Eins abgezählt.
•Der Zähler wird ausgedruckt, wenn
das Ergebnis berechnet wird.
•Durch Drücken von , oder
wird der Zähler gelöscht.
2) Wenn der Wahlschalter für Gesamt-
summe/Einstellung der Rate auf “GT”
(Gesamtsumme) eingestellt ist, wird dem
Postenzähler jedesmal eine Eins
hinzugefügt, wenn Rechenergebnisse im
Gesamtsummenspeicher gespeichert
BETRIEBSTASTEN werden. Zum Ausdrucken und Löschen
des Zählers die Taste drücken.
3) Dem Speicher-Postenzähler wird
jedesmal beim Drücken von kbei
einer Addition eine Eins hinzugefügt.
Hinweise: •Beim Drücken von bei einer
Subtraktion wird jedesmal eine
Eins vom Postenzähler
abgezählt.
•Der Zähler wird gedruckt, wenn
der Speicher abgerufen wird.
•Durch Drücken von
wird der
Zähler gelöscht.
Hinweis: Der Zähler hat eine maximale Kapazität
von drei Stellen (bis ±999). Wenn der
Zähler den Maximalwert überschreitet, wird
er wieder auf Null zurückgestellt.
RUNDUNGS-WAHLSCHALTER:
Beispiel: Einstellung des Komma-Tabulators auf “2”.
4 ÷9 = 0,444 ... , 5 ÷9 = 0,555 ...
4 9 5 9
0,45 0,56
5/4 0,44 0,56
0,44 0,55
EL-1750PIII(LCO)-Ger 04.9.15, 3:34 PM18