Sharp QS-1760H User manual

QS-1760H
QS-2760H
QS-2770H
ELECTRONIC PRINTING CALCULATOR
CALCULADORA IMPRESORA ELECTRÓNICA
OPERATION MANUAL
MANUAL DE MANEJO
ENGLISH ....................................... Page 2
CALCULATION EXAMPLES ......... Page 28
ESPAÑOL ...................................... Página 15
EJEMPLOS DE CÁLCULOS ......... Página 28

Caution!
The socket outlet shall be installed near the equipment and shall be easily accessible.
Aviso!
El tomacorriente debe estar instalado cerca del equipo y debe quedar bien accesible.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
WARNING - FCC Regulations state that any unauthorized changes or modifications to this
equipment not expressly approved by the manufacturer could void the user’s authority to
operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.

– 1 –
QS-2770H
QS-1760H
QS-2760H
, : QS-2770H only
Sólo en la QS-2770H
THE KEYBOARD EL TECLADO

– 2 –
Thank you for your purchase of the SHARP electronic calculator, model QS-1760H/
2760H/2770H. Your SHARP calculator is specially designed to save work and increase
efficiency in all business applications and general office calculations. Careful reading of
this manual will enable you to use your new SHARP to its fullest capability.
To insure trouble-free operation of your SHARP calculator, we recommend the following:
1. The calculator should be kept in areas free from extreme temperature changes,
moisture, and dust.
2. A soft, dry cloth should be used to clean the calculator. Do not use solvents or a wet
cloth.
3. Turn off the power switch prior to connecting or disconnecting the AC cord.
4. Since this product is not waterproof, do not use it or store it where fluids, for example
water, can splash onto it. Raindrops, water spray, juice, coffee, steam, perspiration,
etc. will also cause malfunction.
5. If you pull out the power cord to cut electricity completely, the presently stored tax
rate will be cleared.
6. If service should be required on this equipment, use only a SHARP servicing dealer,
a SHARP approved service facility or SHARP repair service where available.
7. Do not wind the AC cord around the body or otherwise forcibly bend or twist it.
Note: Unless otherwise specified, the text material applies to all three models.
SHARP will not be liable nor responsible for any incidental or consequential
economic or property damage caused by misuse and/or malfunctions of this product
and its peripherals, unless such liability is acknowledged by law.
WARNING
THE VOLTAGE USED MUST BE THE SAME AS SPECIFIED ON THIS
CALCULATOR. USING THIS CALCULATOR WITH A VOLTAGE HIGHER THAN
THAT SPECIFIED IS DANGEROUS AND MAY RESULT IN A FIRE OR OTHER
TYPE OF ACCIDENT CAUSING DAMAGE. SHARP WILL NOT BE HELD
RESPONSIBLE FOR ANY DAMAGE RESULTING FROM USE OF THIS
CALCULATOR WITH OTHER THAN THE SPECIFIED VOLTAGE.
ENGLISH
INTRODUCTION
OPERATIONAL NOTES

– 3 –
Page
•OPERATING CONTROLS .......................................................................................... 3
•INK RIBBON REPLACEMENT ................................................................................. 11
•PAPER ROLL REPLACEMENT ................................................................................ 12
•ERRORS ................................................................................................................... 13
•DECIMAL SYSTEM ................................................................................................... 13
•SPECIFICATIONS .................................................................................................... 14
•CALCULATION EXAMPLES ..................................................................................... 28
•TAX RATE CALCULATIONS ..................................................................................... 45
•SAMPLE APPLICATIONS ......................................................................................... 47
POWER SWITCH:
When the power switch is turned on, the calculator is ready for operation.
PRINT MODE SELECTOR:
“P” position: The calculator functions as a print/display calculator. (Print
mode)
“•” position: The calculator functions as a display calculator. (Non-print
mode)
Mode change print:
When changing the print mode selector, the following print will appear.
“• • • .... • • • –P” (red print): When changing the selector from P to •.
“• • • .... • • • +P” (red print): When changing the selector from •to P.
GRAND TOTAL / RATE SETTING MODE SELECTOR:
“GT” position: This selector will accumulate the following:
(The symbol “ +” will be printed.)
1. Addition and subtraction totals obtained with the or
key.
2. Product and quotient totals obtained with the or
key.
3. Answers obtained with the or key.
“•” position: Neutral, GT OFF
“ ” position: •Enter the adding tax rate, then press .
•To store a discount rate, press before pressing
.
CONTENTS
OPERATING CONTROLS

– 4 –
•A maximum of 4 digits can be stored (decimal point is
not counted as a digit).
Note: •Be sure to set this selector to the “•” position after storing an
each rate.
•Only one rate can be stored. If you enter a new rate, the previous
rate will be cleared.
ADD MODE SELECTOR:
“A/+” position – Effective only in addition and subtraction:
Use of the A/+ mode permits addition and subtraction of
numbers without an entry of the decimal point. When the
A/+ mode is activated, the decimal point is automatically
positioned according to the decimal selector setting.
EXAMPLES: Set A/+- •-A/x to A/+
A. Set decimal to 2
Enter 123456 Tape prints 1,234.56 +
B. Set decimal to 3
Enter 123456 Tape prints 123.456 +
Use of the , , and keys will automatically override
the Add mode and decimally correct answers will be
printed at the preset decimal position.
EXAMPLES: Set A/+- •-A/x to A/+, 5/4
A. Set decimal to 2
Enter .1234 Tape prints 0.1234 ×
100 100.=
12.34
B. Set decimal to 3
Enter 2 Tape prints 2. ÷
3 3.=
0.667
C. Set decimal to 2
Enter 123 Tape prints 1.23 +
10 10.00 +
11.23
Note that decimal point was entered.
“A/x” position – Multiplication and division:
When the A/x mode is activated, the number entered
before or key will override the add mode. But the
➝

– 5 –
number entered following or key and before (or
, , , , ) key will obey the decimal setting. This
is useful for invoicing.
EXAMPLE: Set A/+- •-A/x to A/x
Set decimal to 2
Enter 7 Tape prints 7.×
3 0.03 =
0.21
Note: Use of the key will automatically override the A/x
mode.
Addition and subtraction:
The A/x mode functions same as the A/+ mode.
“•” position: Neutral
ITEM COUNT MODE SELECTOR:
“IC±” position: 1) The counter will count the number of times that the
key has been pressed in addition.
Note: •Each time the key is used in subtraction, 1
will be subtracted from the count.
•The count is printed when the calculated
result is obtained.
•Pressing of the , , , or key
clears the counter.
2) When the grand total mode selector is in the ON
position (GT), the counter will count the number of
times that the calculation results have been stored in
the grand total memory. To print and clear the count,
press the key.
3) The memory item counter will count the number of
times that the key has been pressed in the addition.
Note: •Each time the key is used in the
subtraction, 1 will be subtracted from the
count.
•The count is printed when the memory is
recalled.
•Pressing of the key clears the counter.
“IC+” position: 1) The counter will count the number of times that the
or has been pressed in addition and subtraction.
Note: •The count is printed when the calculated
result is obtained.

– 6 –
•Pressing of the , , , or key
clears the counter.
2) When the grand total mode selector is in the ON
position (GT), the counter will count the number of
times that the calculation results have been stored in
the grand total memory. To print and clear the count,
press the key.
3) The memory item counter will count the number of
times that the or key has been pressed in
addition and subtraction.
Note: •The count is printed when the memory is
recalled.
•Pressing of the key clears the counter.
“•” position: Neutral, counter is turned off.
Note: The counter has a maximum capacity of 3 digits (up to ±999). If the
count exceeds the maximum, the counter will recount from zero.
FIRST FACTOR ACCUMULATION SELECTOR: (Only QS-2770H)
“FΣ” position: The first factor is automatically added to or subtracted from
the memory. A first factor means the first number in multi-
plication and division and each number is printed with “×I”
and “ ÷ I” respectively.
Ex. 2 ×3 ×5 ÷ 6 =
12 ÷ 7 ×9 =
–56 ×4 ×0.5 =
“•” position: Neutral
CONSTANT MODE SELECTOR:
“K” position: The following constant functions will be performed:
Multiplication: The calculator will automatically remember the first
number entered (the multiplicand) and the instruction.
Division: The calculator will automatically remember the second
number entered (the divisor) and the instruction.
Add-on/Discount/Mark up:
The calculator will automatically remember the first
entered number and key functions for Add-on/Discount/
Mark up calculation.
“•” position: Neutral
ROUNDING SELECTOR:
“” position: An answer is rounded up.
“5/4” position: An answer is rounded off.

– 7 –
“” position: An answer is rounded down.
EXAMPLE: 10.005 ÷ 5 = 2.001
Set decimal to 2,
10.005 5 →2.01
Set decimal to 2, 5/4
10.005 5 →2.00
Note: The decimal point floats during successive calculation by the use of
or key.
In floating decimal point system, an answer is rounded down.
DECIMAL SELECTOR:
Presets the number of decimal places in the answer.
In the “F” position, the answer is displayed in the floating decimal system.
PAPER FEED KEY:
When pressed, advances the paper roll.
Note: You can also pull the paper manually.
RIGHT SHIFT KEY:
Operation of this key in entered numbers or calculated results shifts the
number one digit to the right together with the decimal point. Used for one
digit correction.
GRAND TOTAL KEY:
Prints and clears the “GT” memory contents.
NON-ADD/SUBTOTAL KEY:
Non-add – When this key is pressed right after an entry of a number in the
Print mode, the entry is printed on the left-hand side with the
symbol “#”.
This key is used to print out numbers not subjects to calculation
such as code, date, etc.
Subtotal – Used to get subtotal(s) of additions and/or subtractions. When
pressed following the or key, the subtotal is printed with
the symbol “ ◊ ” and the calculation may be continued.
By pressing this key even in the Non-print mode, the displayed number
is printed with the symbol “P”.
TOTAL KEY:
Prints the total of addition and subtraction with the symbol “ ”. This key also
serves as a clear key for the calculation register and resets an error
condition.

– 8 –
CLEAR ENTRY KEY:
Clears number entered prior to use of a function key.
Also used to clear an overflow error caused by an entry.
Ex. 123 ×455 →123 ×456 =
Press 123 455 456
~NUMERAL KEYS
MINUS EQUALS KEY:
Prints the entered number with a “–” symbol and subtracts the number from
the contents of the calculation register. This key is also used to obtain the
product/quotient in negative multiplication and division and prints it with the
symbol “ ”.
PLUS EQUALS KEY:
Prints the entered number with a “+” symbol and adds the number to the
contents of the calculation register. This key is also used to obtain the results
in multiplication and division and prints the product/quotient with the symbol
“”.
PERCENT KEY
DIVISION KEY
MULTIPLICATION KEY
FIRST MEMORY PLUS KEY
FIRST MEMORY MINUS KEY
FIRST RECALL MEMORY KEY
FIRST RECALL AND CLEAR MEMORY KEY
SECOND RECALL AND CLEAR MEMORY KEY
SECOND RECALL MEMORY KEY
SECOND MEMORY MINUS KEY
SECOND MEMORY PLUS KEY
DATE KEY: (only QS-2770H)
Can be used to store and display/print or recall the date or any other factor
for repeated use in an application.
AVERAGE KEY:
Used to calculate the average.