Sharp FV-DB1E User manual

04/4/13 FVDB1E_FRONT.fm TINSEA025SJZZ
Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
DAB RECEIVER
FV-DB1E TINSEA025SJZZ 1
MODEL
OPERATION MANUAL
FV-DB1E
If you require any advice or assistance regarding
your Sharp product, please visit our web-site
www.sharp.co.uk/customersupport.
Customers withoutInternet accessmay telephone
08705 274277during officehours (or(01) 6760648
if telephoning from Ireland).
The stylized mark ‘DAB Digital Radio’ is a trademark of Digital One
Limited used under licence, and the stylized ‘R’ mark is a registered
trademark of Digital One Limited.™ & © 2003.
Downloaded from: http://www.usersmanualguide.com/

2
FV-DB1E
04/4/12 FV-DB1E_1.fm TINSEA025SJZZ
Important Instruction
Special notes
NOTES FOR USERS IN THE U.K. AND IRELAND
The mains lead of this product is fitted with a non-rewireable
(moulded) plug incorporating a 3A fuse. Should the fuse need to
be replaced, a BSI orASTA approved BS 1362 fuse marked or
and of the same rating as above, which is also indicated on
the pin face of the plug must be used.
Always refit the fuse cover after replacing the fuse. Never use
the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being
compatible with the plug supplied, cut-off the mains plug and fit
an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off
plug destroyed immediately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted else-
where into a 13A socket outlet as a serious electric shock may
occur.
To fit an appropriate plug to the mains lead, follow the instruc-
tions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the
following code:
Blue : Neutral
Brown : Live
As the colours of the wires in the mains lead of this product may
not correspond with the coloured markings identifying the termi-
nals in your plug, proceed as follows:
●The wire which is coloured blue must be connected to the plug
terminal which is marked N or coloured black.
●The wire which is coloured brown must be connected to the
plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to
the earth terminal in your three pin plug.
Before replacing the plug cover, make sure that:
●If the new fitted plug contains a fuse, its value is the same as
that removed from the cut-off plug.
●The cord grip is clamped over the sheath of the mains lead
and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELEC-
TRICIAN.
SERVICE INFORMATION
In the unlikely event of your equipment requiring repair, please
contact the dealer or supplier from whom it was purchased. Where
this is not possible, please visit our web-site www.sharp.co.uk/
customersupport.
Customers without internet access may telephone 08705
274277 during office hours (or [phone] if telephoning
from lreland).
Please note; all calls will be charged at local rate.
Certain replacement parts and accessories may be obtained from
our main parts distributor.
WILLOW VALE ELECTRONICS LTD.
0121 766 5414
In the unlikely event of this equipment requiring repair during the
guarantee period, you will need to provide proof of the date of
purchase to the repairing company.
Please keep your invoice or receipt, which is supplied at the
time of purchase.
0301
Downloaded from: http://www.usersmanualguide.com/

3
FV-DB1E
04/4/12 FV-DB1E_1.fm TINSEA025SJZZ
General Information
WARNINGS
!The supplied AC adaptor contains no user serviceable parts.
Never remove covers unless qualified to do so. It contains dan-
gerous voltages, always remove the mains plug from the main
outlet socket before any service operation or when not in use for
a long period.
!The AC adaptor supplied with the FV-DB1E must not be used
with other equipment.
!Never use an AC adaptor other than the one specified. Other-
wise, problems or serious hazards may be created.
!This unit contains no user serviceable parts. Never remove cov-
ers unless qualified to do so. This unit contains dangerous volt-
ages, always remove mains plug from the socket before any
service operation and when not in use for a long period.
!To prevent fire or shock hazard, do not expose this appliance to
dripping or splashing. No objects filled with liquids, such as
vases, shall be placed on the apparatus.
NOTES
!This equipment complies with the requirements of Directives 89/
336/EEC as amended by 93/68/EEC.
!The letters in brackets contained in the model number indicate
the colour of the product only. Operation and specifications are
unaffected.
Accessories
Please confirm that the following accessories are included.
Note:
Only the above accessories are included.
Contents
Page
"General Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
"Preparation for Use
Power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
"DAB (Digital Audio Broadcasting) Operation
Listening to the DAB (Digital Audio Broadcasting) . . . . . .8 - 10
Various settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Changing the information display . . . . . . . . . . . . . . . . . . . . . . 12
"FM Operation
Listening to the FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
"Advanced Features
Storing stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Alarm operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 16
Sleep operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
"References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
TERMS OF GUARANTEE . . . . . . . . . . . . . . . . . . . . . . .Back cover
AC adaptor 1 "AA" size battery (UM/SUM-3,
R6, HP-7 or similar) 2
(RADPAA001SJZZ)
FV-DB1E TINSEA025SJZZ 2
1
Downloaded from: http://www.usersmanualguide.com/

4
FV-DB1E
04/4/12 FV-DB1E_1.fm TINSEA025SJZZ
General Information
Precautions
"General
!Please ensure that the equipment is positioned in a well venti-
lated area and ensure that there is at least 10 cm (4") of free
space along the sides, top and back of the equipment.
!Do not place anything on top of the unit.
!Do not expose the unit to moisture, to temperatures higher than
60°C (140°F) or to extremely low temperatures.
!If your unit does not work properly, disconnect the AC adaptor
from the wall socket. Plug the AC adaptor back in, and then turn
on your unit.
!Do not use an external power supply, other than the 9 V DC sup-
plied with this unit as it may be damaged.
!SHARP is not responsible for damage due to improper use. Refer
all servicing to a SHARP authorised service centre.
!No naked flame sources, such as lighted candles, should be
placed on the apparatus.
!Attention should be drawn to the environmental aspects of bat-
tery disposal.
!The apparatus is designed for use in moderate climate.
!This unit should only be used within the range of 5°C - 35°C
(41°F - 95°F).
Warning:
The voltage used must be the same as that specified on this unit.
Using this product with a higher voltage other than that which is
specified is dangerous and may result in a fire or other type of acci-
dent causing damage. SHARP will not be held responsible for any
damage resulting from use of this unit with a voltage other than that
which is specified.
"Volume control
It is advisable to avoid exposure to high volume levels. Do not turn
on the unit with the volume set to the maximum. Keep the volume
moderate when listening to music.
!Use the unit on a firm, level surface free from
vibration.
!Keep the unit away from direct sunlight,
strong magnetic fields, excessive dust,
humidity and electronic/electrical equip-
ment (home computers, facsimiles, etc.)
which generate electrical noise.
!In case of an electrical storm, unplug the
unit for safety.
10 cm (4")
10 cm (4")
10 cm (4") 10 cm (4")
!Hold the AC adaptor plug by the head when
removing it from the wall socket, as pulling
the lead can damage internal wires.
!Do not remove the outer cover, as this
may result in electric shock. Refer inter-
nal service to your local SHARP service
facility.
!The ventilation should not be impeded by
covering the ventilation openings with
items, such as newspapers, tablecloths,
curtains, etc.
Downloaded from: http://www.usersmanualguide.com/

5
FV-DB1E
04/4/12 FV-DB1E_1.fm TINSEA025SJZZ
General Information
Controls and indicators
Reference page
1.On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.Preset Number Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.Preset Zone Select Button . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.Auto Tune Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.Information Select Button . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.Band Select Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 13
7.Alarm or Sleep Set Indicator . . . . . . . . . . . . . . . . . . . . . 15, 16
8.Menu Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
9.Clock Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 15, 16
10.Tuning Down or Item Select Button . . . . . . . . . . . . . 9, 10, 13
11.Volume Up and Down Button . . . . . . . . . . . . . . . . . . . . . . . . 7
12.Tuning Up or Item Select Button . . . . . . . . . . . . . . . 9, 10, 13
13.Enter Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
14.Sound Mode Select Button . . . . . . . . . . . . . . . . . . . . . . . . . . 7
15.DAB Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
16.FM Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
17. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 13
18.FM Stereo Receiving Indicator . . . . . . . . . . . . . . . . . . . . . . 13
19.Preset Zone Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
20.Preset Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 14
21.Primary with Secondary Indicator . . . . . . . . . . . . . . . . . . . . 9
22.Secondary Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
23.Telescopic Rod Aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
24.Optical Digital Output Socket . . . . . . . . . . . . . . . . . . . . . . . 17
25.Analogue Line Output Socket . . . . . . . . . . . . . . . . . . . . . . . 17
26.Headphone Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
27. Battery Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
28.DC 9 V Input Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
123
2423 25 26
78910
27 28
11
15 16 17 18 19 20 2122
12 1413
456
1
Downloaded from: http://www.usersmanualguide.com/

6
FV-DB1E
04/4/12 FV-DB1E_1.fm TINSEA025SJZZ
Preparation for Use
Power source
"Inserting memory batteries
Memory batteries maintain the clock setting and preset stations for
the tuner.
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Notes:
!If memory batteries are not inserted or low, preset stations and
the clock setting will be lost.
!Enter the power stand-by mode and connect the AC adaptor
before replacing memory batteries. Otherwise preset stations
and the clock setting will be lost.
!Replace memory batteries approximately once a year.
"Using with the main batteries
When the unit is powered by the main batteries, make sure to install
memory batteries. Otherwise preset stations, the clock setting and
DAB setting will be all lost when the main batteries run out.
Battery replacement:
When batteries are low, sound decreases or becomes distorted.
Replace the batteries with new ones.
"Using with the AC adaptor
Plug the AC adaptor into the wall socket, and then insert the plug on
the other end into the DC 9V socket.
Notes:
!Unplug the AC adaptor from the wall socket if the unit will not be
used for a prolonged period of time.
!
Connecting the AC adaptor to the unit disconnects the main batteries.
!Use only the supplied AC adaptor. Using other AC adaptor may
cause an electric shock or fire.
1Open the battery com-
partment.
2
Insert the supplied 2 "AA"
size batteries (UM/SUM-3,
R6, HP-7 or similar) into
the battery compartment.
Insertion and removal:
Push the battery toward to insert or remove.
3Close the battery compartment.
Precautions for battery use:
! Installing the batteries incorrectly may cause the unit to malfunction.
!Insert the batteries according to the direction indicated in the
battery compartment.
! Remove the batteries if the unit is not to be used for long periods
of time. This will prevent potential damage due to battery leakage.
!Replace all old batteries with new ones at the same time.
!Do not mix old and new batteries.
1
2
1 Disconnect theAC adaptor, and open the battery compartment.
2 Insert 6 "C" size batteries
(UM/SUM-2, R14, HP-11 or
similar) into the battery
compartment.
"C" size batteries (UM/SUM-2, R14, HP-11 or similar) are not
included.
Insertion and removal:
Push the batteries and toward to insert or remove.
3Close the battery compartment.
54
213
6
Wall socket
(AC 230 - 240 V 50/60 Hz)
To the DC 9V socket
Downloaded from: http://www.usersmanualguide.com/

7
FV-DB1E
04/4/12 FV-DB1E_1.fm TINSEA025SJZZ
Preparation for Use
General control
"To turn the power on
Press the ON/STAND-BY button to turn the power on.
When turned on for the first time, the unit scans radio stations
automatically to create the station list (see page 8).
Note:
The backlight brightness changes after a while.
After 30 seconds of inactivity, the backlight dims (when using the AC
adaptor) or turns off (when using batteries). Press a button to turn it
back on.
"Adjusting the volume
Press the VOLUME (+ or -) button to increase or decrease the vol-
ume.
"Adjusting the bass
1 Press the SOUND button to select "Bass".
2
Within 30 seconds, press the VOLUME control to adjust the bass.
"Adjusting the treble
1 Press the SOUND button to select "Treble".
2
Within 30 seconds, press the VOLUME control to adjust the treble.
"Checking date and time
When a DAB (Digital Audio Broadcasting) station is received, date
and time are set automatically.
When "No time date" appears, receive a DAB station to set date
and time.
Notes:
!If memory batteries are not inserted or low, the clock setting will
be lost. This can be avoided when the AC adaptor is connected.
The clock setting will be lost if the unit is powered only by the
main batteries and set to the power stand-by mode.
!Time is displayed in 24-hour format.
After use:
Press the ON/STAND-BY button to enter the power stand-by
mode.
Press the CLOCK button until time and date ap-
pear on the display.
21 39 40
.....
0
... ...
0 +55
... ...
0 +55
2
Downloaded from: http://www.usersmanualguide.com/

8
FV-DB1E
04/4/12 FV-DB1E_1.fm TINSEA025SJZZ
DAB (Digital Audio Broadcasting) Operation
Listening to the DAB (Digital Audio Broadcasting)
"About DAB (Digital Audio Broadcasting)
Digital Audio Broadcasting is a digital transmission system where
audio signals are converted to digital signals for broadcasting.
DAB is broadcast as a group of data called multiplex (ensemble)
which may contain one or more stations (services). Each station
contains a primary service and there may be one or more second-
ary services.
This allows several programmes or services to be transmitted on a
single frequency.
"Auto tune
When turned on for the first time, the unit scans radio stations
automatically to create a station list.
!12-digit solid blocks show the progress of scan.
!The number of received stations is displayed.
After the scan:
The stations will be stored in alphanumeric order and the first station
on the list will be selected and you will hear it through the speaker.
!To listen to other stations, see "Selecting a station in the station
list" on page 9.
!You can arrange the order of stations in the station list (see page
11).
Notes:
!If no station is found, "No station" appears.
!Up to 99 appears for total received stations.
Aerial adjustment:
Raise and extend the telescopic
rod aerial, then adjust the posi-
tion and length for the best re-
ception.
DAB SIGNAL
MULTIPLEX
(ENSEMBLE)
SERVICES
SERVICE
COMPONENTS
(STATIONS)
Total received stations
Downloaded from: http://www.usersmanualguide.com/

9
FV-DB1E
04/4/12 FV-DB1E_1.fm TINSEA025SJZZ
DAB (Digital Audio Broadcasting) Operation
"Retuning the unit (Auto tune)
You can retune the radio when you move the unit to other areas or
add multiplex channels to the station list.
There are two Auto tune options available.
After the scan:
The unit will return to the station you were listening to and you will
hear it through the speaker. All the stations found are now stored in
the unit.
"Selecting a station in the station list
Once a DAB station is received, you can select stations in the sta-
tion list.
Note:
Inactive stations cannot be received by Auto tune ("Not available"
appears). Tune in manually by adjusting the aerial direction (see
page 10).
Autotune UK: All frequencies are scanned in the UK channel allo-
cation. This may take a few seconds.
Autotune Full: The full range of digital frequencies is scanned in
Band III. This may take a minute or more.
1Press the BAND button until "DAB" ap-
pears on the display.
2Autotune UK:
Press the AUTO TUNE button for less
than 1 second.
Autotune Full:
Hold down the AUTO TUNE button for 2
seconds or more.
You can cancel the Auto tune by pressing the AUTO TUNE but-
ton again.
1Press the BAND button until "DAB" appears on the display.
2Whilst receiving a DAB station, press the TUNING ( or )
button repeatedly to select the desired station.
!The upper part of the display shows the current station
name, and the name of the station being scanned (with "
") appears in the lower part.
The current station name
The name of the station being scanned
!If a station has one or more secondary
services, " " appears after to the station
name. You can select a secondary ser-
vice.
!Whilst selecting a secondary service,
" " appears before the station name.
This indicates a primary service is avail-
able.
3Within 30 seconds, press the ENTER button.
!Whenthecurrentstationisprimarywithsecondary,"P"lights
up.
!When the current station is secondary, "S" lights up.
!When the current station is primary without other services,
no indicator lights up.
3
Downloaded from: http://www.usersmanualguide.com/

10
FV-DB1E
04/4/12 FV-DB1E_2.fm TINSEA025SJZZ
DAB (Digital Audio Broadcasting) Operation
Listening to the DAB (Digital Audio Broadcasting) (continued)
!Manual tune
You can manually store stations which Auto tune cannot find. If
reception is poor, you can adjust the sensitivity.
Manual tune is only available after Auto tune. Perform Auto tune
first.
Exiting Manual tune:
Press the ENTER button to exit manual tuning.
1Press the BAND button until "DAB" ap-
pears on the display.
2Press the MENU button repeatedly to
select "Manual tune".
3Within 30 seconds, press the ENTER
button.
4Within 30 seconds, press the TUNING
( or ) button to tune in to the desired
station.
5Within 30 seconds, press the ENTER button.
"Reception sensitivity appears. The
white block indicates the minimum re-
quiredlevelandthesolidblocksindicate
the current level.
"If the level is below the white block,
move the rod aerial or unit to improve re-
ception. When the level reaches the
white block, a multiplex name appears
and the multiplex will be added to the
service list.
Downloaded from: http://www.usersmanualguide.com/

11
FV-DB1E
04/4/12 FV-DB1E_2.fm TINSEA025SJZZ
DAB (Digital Audio Broadcasting) Operation
Various settings
!Changing the station order
You can change the order of stations in the station list. !Adjusting the DRC value When the volume is low, adjust the DRC (Dynamic Range Control)
value to make the sound more audible (may not available for some
broadcast material).
1Press the BAND button until "DAB" ap-
pears on the display.
2Press the MENU button repeatedly to
select "Station order".
3Within 30 seconds, press the ENTER
button.
4Within 30 seconds, press the TUNING ( or ) button to
select the desired station order.
Alphanumeric:
All stations are displayed in alphanumeric order. This is the de-
fault setting.
Fav. station:
The 10 most recent stations appear as "Fav." and then appear
in alphanumeric order.
Active station:
The station list shows receivable stations and then others in al-
phanumeric order.
Multiplex:
Stations are sorted by frequency, in ascending order.
Trim stn. list:
Delete inactive stations from the list.
5Within 30 seconds, press the ENTER
button.
1Press the BAND button until "DAB" appears on the display.
2Press the MENU button repeatedly to
select "Set DRC Value".
3Within 30 seconds, press the ENTER
button.
4Within 30 seconds, press the TUNING
( or ) button to select the desired
DRC value.
DRC 1: Dynamic range is controlled as set for the broad-
cast. This is the default setting.
DRC 0: DRC is off.
DRC 1/2: Dynamic range is controlled half as much as the
level set for the broadcast.
5Within 30 seconds, press the ENTER
button.
3
Downloaded from: http://www.usersmanualguide.com/

12
FV-DB1E
04/4/12 FV-DB1E_2.fm TINSEA025SJZZ
DAB (Digital Audio Broadcasting) Operation
Changing the information display
You can switch information in the lower part of display.
Press the INFO button.
Each time the button is pressed, the information display changes in the following order.
When "Not available" appears, the INFO button does not allow you to change the display.
Display Description
Scrolling text Information scrolls across the display when sent from the station (set by default).
You can pause, forward, or reverse scrolling text.
Pausing text scroll: Press the ENTER button.
Forwarding/reversing text scroll: Whilst text scroll is paused, press the TUNING ( or ) button. Press once to
move forward one character, hold down to scroll through, and release to return to
the pause mode.
Resuming text scroll: Whilst text scroll is paused, press the ENTER button again.
Programme type A description of the type of content being broadcast by the station.
Multiplex name The name of the multiplex (ensemble) which provides the current service.
Channel The DAB channel and frequency for the station.
Mode The data transfer speed and channel type (stereo or mono) appear.
Signal quality The signal quality is displayed as a number (0 - 100).
[85-100: Good 70-84: Fair 0-69: Poor]
Sensitivity Sensitivity of reception.
The empty block indicates the minimum required level for reception and the solid blocks indicate the current level.
Downloaded from: http://www.usersmanualguide.com/

13
FV-DB1E
04/4/12 FV-DB1E_2.fm TINSEA025SJZZ
FM Operation
Listening to the FM
Notes:
"When radio interference occurs, auto scan tuning may stop auto-
matically at that point.
"Auto scan tuning will skip weak signal stations.
"To stop the auto tuning, press the TUNING button again.
To receive an FM stereo transmission:
Press the BAND button to display the "ST" indicator.
"" " will appear when an FM broadcast is in stereo.
"If the FM reception is weak, press the BAND button to extinguish
the "ST" indicator. The reception changes to monaural, and the
sound becomes clearer.
1Press the ON/STAND-BY button to turn the power on.
2Press the BAND button until "FM" ap-
pears on the display.
3Press the TUNING ( or ) button to tune in to the desired
station.
Manual tuning:
Press the TUNING button as many times as required to tune in
to the desired station.
Auto tuning:
When the TUNING button is pressed for 2 seconds or more,
scanning will start automatically and the tuner will stop at the
first receivable broadcast station.
FM stereo mode indicator
FM stereo receiving indicator
4
Downloaded from: http://www.usersmanualguide.com/

14
FV-DB1E
04/4/12 FV-DB1E_2.fm TINSEA025SJZZ
Advanced Features
Storing stations
!Memorising a station
You can store up to 20 DAB and FM stations (5 stations for each
zone A-D) and recall them at the press of a button.
For FM stations, stereo and mono modes are memorised.
Note:
If memory batteries are not inserted or low, preset stations will be
lost. When the AC adaptor is connected, preset stations remain
without memory batteries. Preset stations will be lost if the unit is
powered only by the main batteries and set to the power stand-by
mode.
!To recall a memorised station
Note:
If the selected preset number is empty the display shows
"Preset ** empty".
!To erase entire preset memory
1Tune in to the desired station (see page 9, 13).
2Press the PRESET SELECT button repeatedly to select the
desired preset zone.
Zone A
Zone B
Zone C
Zone D
3Hold down the PRESET button (1 - 5) for
2 seconds or more to store the station
in memory.
4Repeat steps 1 - 3 to set other stations, or to change a pre-
set station.
When a new station is stored in memory, the station previously
memorised will be erased.
1Press the PRESET SELECT button repeatedly to select the
desired preset zone.
2Press the PRESET button (1 - 5) for less
than 1 second to recall a station.
1Hold down the PRESET SELECT button
for 2 seconds or more.
2Within 30 seconds, press the ENTER
button.
Downloaded from: http://www.usersmanualguide.com/

15
FV-DB1E
04/4/12 FV-DB1E_2.fm TINSEA025SJZZ
Advanced Features
Alarm operation
At the set time, the alarm sounds or the radio turns on.
Once set, the alarm performs the operation every day.
Use when...
You want to use the alarm as a wake up call, or listen to the radio at
the same time every day.
Before setting alarm:
1When setting the alarm, connect the AC adaptor to the unit.
If batteries are the only power source, you cannot set the
alarm (see page 6).
2 If the clock is not set, the alarm setting is not available ("No
time date" appears). Receive a DAB station to set date and
time (see page 8, 9).
1Press the ON/STAND-BY button to turn the power on.
2To use "Radio" as an alarm, tune in to a station and adjust
the volume.
To use "Tone" as an alarm, proceed to step 3.
3Press the CLOCK button repeatedly to
select "Set alarm ok?", then press the
ENTER button.
4Within 30 seconds, press the TUNING
( or ) button to specify the hour to
start, then press the ENTER button.
5Within 30 seconds, press the TUNING
( or ) button to specify the minutes
to start, then press the ENTER button.
6Within 30 seconds, press the TUNING
( or ) button to select the desired
alarm type.
Tone: The alarm sounds at the set time, and stops after 5
minutes. The volume gradually increases from 0 and
reaches 40 after 1 minute.
Radio: The radio turns on at the set time, and turns off after
1 hour. The volume gradually increases from 0 and
reaches the level set in step 2 after 1 minute.
7Within 30 seconds, press the ENTER
button.
" " will light up.
8At the set time, the alarm operation will start.
"
The current date/time and the remaining time appear alternately.
"The volume decreases 1 minute before the alarm operation
finishes.
5
Downloaded from: http://www.usersmanualguide.com/

16
FV-DB1E
04/4/12 FV-DB1E_2.fm TINSEA025SJZZ
Advanced Features
Alarm operation (continued)
To cancel the alarm setting:
Press the ON/STAND-BY button whilst " " is indicated.
To cancel the alarm operation without setting the unit to the stand-by
mode, press the CLOCK button until "Alarm off ok?" appears on the
display, then press the ENTER button.
To reset or change the alarm setting:
Perform "Alarm operation" from the beginning (see page 15).
Notes:
"The alarm operates at the same time every day until the setting is
cancelled. Cancel the alarm when it is not in use.
"If the unit is unplugged or a power failure occurs in the alarm
stand-by mode, the " " indicator turns off and the alarm setting is
cancelled.
"During the sleep operation, the alarm setting is not available.
Sleep operation
When the set time elapses, sound is muted with the power on.
Before setting sleep:
Stopping the alarm:
Press the ON/STAND-BY button.
About snooze function:
You can pause the alarm sound by press-
ing buttonsother thantheON/STAND-BY
button. In this case, the alarm resumes af-
ter 7 minutes.
The remaining time also appears.
Tone:
The alarm stops after 5 minutes when the snooze is not used. If
you use the snooze repeatedly, the alarm will be disabled after 1
hour.
Radio:
The alarm will be disabled after 1 hour.
For the sleep operation, connect the AC adaptor to the unit.
If batteries are the only power source, setting is not possible
(see page 6).
1Press the CLOCK button repeatedly to
select "Set sleep".
2Within 30 seconds, press the TUNING
( or ) button to select the desired
sleep time.
"Select set time from 1 - 120 minutes by
the minute.
"Press the TUNING ( or ) button onceto advance the time
by 1 minute. Hold it down to advance continuously.
3Within 30 seconds, press the ENTER
button.
"" " will light up.
"Remaining time is displayed during the sleep operation.
"The volume gradually decreases for the last 1 minute.
4Sound will be muted after the set time
elapses.
" " turns off.
To stop the sleep operation:
Press any button on the unit
whilst "Sleeping" is displayed.
Sleep operation stops.
To cancel the sleep setting:
Press the ON/STAND-BY button whilst " " is indicated.
To cancel the sleep operation without setting the unit to the stand-by
mode, press the CLOCK button until "Sleep off ok?" appears on the
display, then press the ENTER button.
21 119 120
...
Downloaded from: http://www.usersmanualguide.com/

17
FV-DB1E
04/4/12 FV-DB1E_2.fm TINSEA025SJZZ
Advanced Features
Enhancing your system
!Digital connection to an MD recorder, etc.
You can record DAB sound using an MD recorder, etc.
Notes:
"Plug in each cable fully to prevent noise interference.
"Refer to the manual for the connected equipment.
"FM signals are not sent from the DIGITAL OUT socket.
!Connecting to a stereo system, etc.
You can enjoy the sound through a stereo system by connecting to
the unit with an audio cable.
Notes:
"Plug in each cable fully to prevent noise interference.
"Refer to the manual for the connected equipment.
"The unit produces both DAB and FM sound.
!Headphones
"Before plugging in or unplugging the headphones, reduce the vol-
ume.
"Be sure your headphones have a 3.5 mm (1/8") diameter plug
and impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
"Plugging in the headphones disconnects the speakers automati-
cally. Adjust the volume using the VOLUME control.
Stereo system, etc.
MD recorder, etc. Headphones
To optical digital
audio input socket
To the
line input
sockets
Optical digital cable
(commercially
available)
Audio cable
(commercially
available)
Turn off all other equipment before making this connection.
5
Downloaded from: http://www.usersmanualguide.com/

18
FV-DB1E
04/4/12 FV-DB1E_2.fm TINSEA025SJZZ
References
Troubleshooting chart
Many potential problems can be resolved by the owner without call-
ing a service technician.
If something is wrong with this product, check the following before
calling your authorised SHARP dealer or service centre.
!If trouble occurs
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
If such a problem occurs, do the following:
Caution:
This operation will erase all data stored in memory including clock,
alarm settings, tuner preset, and station list, etc.
!Clearing all the memory (reset)
Caution:
This operation will erase all data stored in memory including clock,
alarm settings, tuner preset, and station list, etc.
!Condensation
When condensation is formed, the unit may not function properly.
Condensation may form in the following cases:
"Shortly after turning on a heater.
"When the unit is placed in a room where there is excessive steam
or moisture.
"When the unit is moved from a cool place to a warm place.
To remove condensation:
Leave the unit for approximately 1 hour. The condensation should
evaporate and the unit will work properly.
Symptom Possible cause
When a button is
pressed, the unit
doesnotrespond.
"Set the unit to the power stand-by mode and
then turn it back on.
"If the unit still malfunctions, reset it.
No sound is
heard. "Is the volume level set to "0"?
"Are the headphones connected?
DAB channels
cannot be
received.
"Signal reception is poor. Adjust the aerial di-
rection (see page 8).
"Move the unit to another room or near the
window, then tune in manually
(see page 10).
Sound from DAB
channels is
interrupted or
distorted.
"Is the unit placed near the TV or computer?
"Move the unit to another room or near the
window, then tune in manually
(see page 10).
"Are the main batteries dead?
Secondary
services cannot
be received.
"Some DAB channels do not offer secondary
services. " "appears the stationnamewhen
secondary services are available
(see page 9).
The alarm does
notstartattheset
time. Or " " is
flashing.
"Is the AC adaptor of the unit plugged in?
"Did a power failure occur? Receive a DAB
station to set date and time (see page 8, 9).
The unit does not
store stations, or
the clock does
not keep time.
"Are the memory batteries dead?
"Is the memory battery polarity correct?
1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in the previous operation, unplug and
plug in the AC adaptor from the wall socket and replace the main
batteries, memory batteries and then turn the power on.
1 Press the ON/STAND-BY button to enter the stand-by mode.
2 Whilst pressing down the PRESET 1 button and the PRESET
SELECT button, press the ON/STAND-BY button until "All clear
ok?" appears.
3 Within 30 seconds, press the ENTER button.
"Complete" appears and the memory is cleared.
Downloaded from: http://www.usersmanualguide.com/

19
FV-DB1E
04/4/12 FV-DB1E_2.fm TINSEA025SJZZ
References
Maintenance
!Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.
Caution:
"Do not use chemicals for cleaning (petrol, paint thinner, etc.). It
may damage the cabinet finish.
"Do not apply oil to the inside of the unit. It may cause malfunc-
tions.
Specifications
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification fig-
ures indicated are nominal values of production units. There may be
some deviations from these values in individual units.
!General
!Radio
Type DAB receiver
Power source DC 9 V: AC adaptor
(AC 230 - 240 V, 50/60 Hz)
DC9 V:["C"size(UM/SUM-2,R14,orHP-11)
battery 6 as main batteries]
DC 3 V:["AA"size (UM/SUM-3, R6, or HP-7)
battery 2 as memory batteries]
Power
consumption 8 W (AC adaptor)
Output power RMS: 4 W (2 W + 2 W) (10 % T.H.D.)
Speaker 8 cm full-range speaker
Output terminals
Headphones:3.5mm stereomini plug type 1
16 - 50 ohms (recommended: 32 ohms)
Line output (audio signal):
3.5 mm stereo mini plug type 1
2 V/10 k ohms at DAB 0 dB
Digital output (optical): Square type 1
Dimensions Width: 320 mm
Height: 135 mm
Depth: 100 mm
Weight 1.65 kg (without batteries)
Frequency range DAB: 174 - 240 MHz
FM: 87.5 - 108 MHz
6
Downloaded from: http://www.usersmanualguide.com/

TERMS OF GUARANTEE
Sharp Electronics (UK) Ltd. (“Sharp”) guarantees to provide for the repair, or at its option the replace-
ment, of this product subject to the conditions listed below:-
1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It does
not cover faults or damage caused by accident, misuse, fair wear and tear, neglect, tampering with
the product, or repair other than by a Service Facility appointed by Sharp.
2. As this product is intended for private domestic use only, the guarantee will not apply if the product
is used in the course of a business, trade or profession.
3. To benefit from this guarantee, any fault which occurs must be notified to Sharp, or its appointed
Service Facility within one year from the date this product was purchased. Proof of purchase must
be provided.
4. The guarantee does not cover carriage costs, audio tapes, compact discs or batteries.
5. In the unlikely event of this product requiring repair, please contact the supplier from whom it was
purchased. Where this is not possible, please contact the Sharp Customer Information Centre on
the telephone number given below.
6. No person has any authority to vary the terms or conditions of this guarantee.
7. This guarantee is offered as an additional benefit to your statutory rights, and does not affect these
rights in any way.
If you have any difficulty operating this product, or would like information on other Sharp products,
please telephone the Sharp Customer Information Centre on the number given below.
Sharp Customer Information Centre - Telephone [phone]
(or [phone] if telephoning from Ireland)
0310
04/4/12 FVDB1E_BACK.fm TINSEA025SJZZ
SHARP ELECTRONICS (U.K.) LTD.
Sharp House, Thorp Road, Newton Heath, Manchester, M40 5BE
SHARP CORPORATION 0401_A5
TINSEA025SJZZ
04D N AO 1
Downloaded from: http://www.usersmanualguide.com/