Shaw HDPVR 830 Instruction sheet

Power HDMI Shaw Direct Remote
1. Connect the 2 coax cables from your wall to the “Sat 1”
and “Sat 2” ports on your set-top box. Make sure the
connection is secure.
SAT 2SAT 1 VIDEO USBDIGITAL
AUDIO
INTERNET SERIAL POWERAUDIO
OUT
L R
SAT 2
SAT 1
VIDEO
Wall Outlet
SAT 1 SAT 2
What’s in the box?
Time to get connected
2. Connect the HDMI cable to the HDMI port on your set-top box and the HDMI
port on your TV. You can also use RCA cables (not included) for a standard
definition TV.
Turn on your TV and set it to the same HDMI input you connected the cable to.
SAT2SAT1 VIDEO USBDIGITAL
AUDIO
INTERNET SERIAL POWERAUDIO
OUT
L R
HDMI Out
HDMI In
Television
Set-Top Box
(HDPVR 830)
SAT 1 VIDEO USB INTERNET SERIAL POWERAUDIO
OUT
L R
Power
3. Connect the power cord to the set-top box and an electrical outlet.
Wait one minute while your set-top box powers on.
4. When prompted, use your new Shaw Direct remote to go through a short
initial setup process. If you have Internet, connect your set-top box to
your WiFi network for instant access to Video On Demand and
Pay-Per-View titles.
If you would like to control your TV without pointing the remote directly at
your set-top box, enable UHF (ultra high frequency) when prompted on the
next screen, or simply choose to disable this setting.
5. Continue to follow the on-screen prompts until the screen reads ‘Signal Found!’
This step should take approximately 5 minutes to complete.
1
2
3
How to install your new set-top box.
Follow these simple steps to install your new set-top box and your new Shaw Direct remote.

Time to activate
1. Go to shawdirect.ca/myaccount and log in. Select Activate your set-top box and Submit. Or, call the activation line
at 1-855-874-6953 and follow the prompts.
2. Within a few moments, the ‘Trip Count’ value on your screen will increase from 0. After that you will be notified
when your set-top box is fully activated – this may take up to 10 minutes.
Don’t worry if all your guide and channel information is not available yet, it may take up to one hour to load.
Recycling Equipment
If you are replacing your old set-top box, check the model number located at the bottom left corner. If the model is
HDDSR 600, HDDSR 605 or HDPVR 630 you can recycle this equipment along with the accessories like remotes
and cables.
To find a local drop-off location near you, visit epra.ca
Programming your new Shaw Direct Remote to your TV (Optional)
1. Review the Shaw Direct remote control manual, which is included in the box or can
be viewed at shawdirect.ca/remote and search for the brand of your TV. Note the
corresponding codes for your TV brand.
2. Ensure the TV is powered on.
3. At the top of your remote, press and hold the TV button until the other buttons at
the top of the remote (AUX, SAT) flash at least 3 to 4 times.
4. Enter 5-digit code that you noted in step 1.
5. Press the POWER button.
6. If the TV turns off, you have successfully programmed your remote with the TV.
Press the POWER button to turn it back on.
7. If the TV does not power on, repeat steps 3 and 4 using different codes given for
your brand of your TV. You may have to repeat this process a couple of times until
the correct code is entered.
Need more help?
For more tips and tricks, including transferring your existing settings to your new set-top box, visit shawdirect.ca/DSR.
You can also visit shawdirect.ca/support to access a library of online guides, articles and videos.
SD_830HDPVR_INSTALL_0523