Shimano SRD Programming manual

ROWING
SRD Footstretcher Assemblin
g
Manual
g
Shimano,Inc
© 2009 Shimano, Inc. ALL RIGHTS RESERVED 1

ROWING
Index
■Getting started
(1) Check contents in the box ………………………………...………P3
(
2
)
Genuine Boat Parts A
pp
lied to SRD ……………………..………P4
()
pp
(3) Tools …………………………………………………………………P5
■Installing and Adjusting
(4) Installing Attachment Pipe …………………………………………P6
(5) Installing the Upper Pipe ……………………………………………P7
(6) Temporary Assemble ………………………………………….……P8
(7) Adjusting the Footstretcher Angle …………………………………P9
(8)
Ch ki th S P10
(8)
Ch
ec
ki
ng
th
e
S
pace …………………………………………………
P10
(9) Adjusting the Stance …………………..…………………………….P11
(10) Fixing the Frame Unit ………………………..…………………….P12
(11) Adjusting the Height of the Binding Units ……….……………….P13
(12) Adjusting the position of the SRD Footstretcher System ………P14
(12) -1/2/3 How you can measure the position …....………………….P15
(14) Adjusting the Heel Plates …....…………………………..………. P17
(15) Adjusting the Step-in Position …....…………………..…………. P18
(16) Adjusting the Binding Tension …....…………………………..…. P19
(17)
Installing the Cleats
P20
(17)
Installing
the
Cleats
…....………………………………………….
P20
(18) Adjusting the position of the Cleats …............…………………. P21
■Note
NOTE
P23
© 2009 Shimano, Inc. ALL RIGHTS RESERVED 2
NOTE
…....……………………………………………………………….
P23

ROWING
(1) Check contents in the box
FUit
FUit
F
rame
U
n
it
（right）
F
rame
U
n
it
（left）
Binding Unit
（right）
Binding Unit
（left）
KF-R600
Attachment Pipe Lower Fitting
• These are all in the package.
• Binding units are fixed on the Frame Units in
the package.
© 2009 Shimano, Inc. ALL RIGHTS RESERVED 3

ROWING
(2) Genuine Boat Parts Applied to SRD
Upper Pipe
Mounting(left)
Mounting(left)
Upper Pipe
Mounting(right)
Upper Pipe(25mm φ)
• These genuine parts should be
a
pp
lied from
y
our boat to mount
pp y
SRD Footstretcher.
Lower Mounting
© 2009 Shimano, Inc. ALL RIGHTS RESERVED 4

ROWING
(3) Tools
A B
C
D
Ａ：Hexagon Wrenches(3mm will be used
mainly)
Ｂ：Angle Meter
Ｃ：Ta
p
e Measure
E
p
Ｄ：String
Ｅ：Tool(s) each boat manufacturer recommend
to fix the Footstretcher system. In this photo
10mm Wrench is shown.
Ｆ
LAli RtlPi
F
Ｆ
：
L
ong
Al
um
i
num
R
ec
t
ang
l
e
Pi
pe
Ｇ：Level
G
© 2009 Shimano, Inc. ALL RIGHTS RESERVED 5

ROWING
(4) Installing Attachment Pipe
・Loosen up 4 bolts fixing the
Lower Pipe.
・Put the Lower Fitting part on
the Lower Pipe
・Let the Lower Pipe go through the
metal fitting cramps, then tighten
til(Ydtht
・Install the Lower Pipe.
t
emporar
il
y.
(Y
ou
d
o no
t
h
ave
t
o
tighten these firmly before the
procedure (6) )
© 2009 Shimano, Inc. ALL RIGHTS RESERVED 6

ROWING
(5) Installing the Upper Pipe
Procedure (5) -1: Loosen the
bolts shown by orange arrows
(
↑
)and slide down the Binding
Procedure (5) -2: Loosen the
bolts shown b
y
g
reen arrows
(
↑
)
(
↑
)and
slide
down
the
Binding
Unit. With this operation it will
be easier to manipulate the
Upper Pipe.
yg (
↑
)
and install the upper pipe.
© 2009 Shimano, Inc. ALL RIGHTS RESERVED 7

ROWING
(6) Temporary Assemble
• Put your SRD Footstretcher on the boat by
using tools the boat manufacturer
recommends.
•CAUTION: Do not too much loosen the
bolts on the Binding Units shown on
p
r
ocedu
r
e
(5)
-1
,
ot
h
e
rwi
se
t
h
e
u
ni
t
mi
g
h
t
p ocedu e
(5)
,ote seteu t gt
slide down on the Frame Unit and result in
damaging the hull.
！
CAUTION:
DO NOT let the Binding Units slide down
© 2009 Shimano, Inc. ALL RIGHTS RESERVED 8

ROWING
(7) Adjusting the Footstretcher Angle
• Adjust the angle of SRD
Footstretcher system by sliding the
Footstretcher
system
by
sliding
the
upper pipe up and down.
• The standard setting of the angle is
50 degrees up from horizontal.
• You can check it by applying the
angle meter on the Frame Unit.
50°
*All the bolts on Footstretcher system has to be fastened when
you try to check the precise angle, otherwise the
measurements will be inaccurate
© 2009 Shimano, Inc. ALL RIGHTS RESERVED 9
measurements
will
be
inaccurate
.

ROWING
(8) Checking the Space
• Allow 1CM space between the edge of the
SRD Footstretcher system and the inside of
the hull. It is easier to check whether the
s
p
ace is enou
g
h or not b
y
movin
g
a small
pgyg
stick such as a pencil around the
Footstretcher.
• CAUTION: To avoid the damage to the hull,
this space must be there The Footstretcher
this
space
must
be
there
.
The
Footstretcher
system sags slightly when strong force is
applied on it.
• If the lower end of the Frame Units are
hitting the hull, change the position of the
lower pipe fitting cramps.
© 2009 Shimano, Inc. ALL RIGHTS RESERVED 10