Shimpo DT-2100 User manual

After carefully reading this manual, be sure to store it in a safe
and convenient place for easy reference.
Thank you for purchasing Nidec-Shimpo's Handheld High-Performance Digital
Tachometer DT-2100. For instructions on how to use this product properly and
optimally for a long period of time, please be sure to read this manual thoroughly
before use.
Before operation, maintenance and inspection, please
carefully read this instruction manual and follow it for
proper use.
DT-2100
Instruction Manual
99265A
Before operation, maintenance and inspection, please carefully read this instruction man-
ual and follow it for proper use. Start using only after you have read about the equipment’
s functions, safety information and precautions.
This instruction manual provides three grades of safety warnings: "Danger", "Warning"
and "Caution". Each of them is an important description related to safety. Be sure to fol-
low them.
Warning This indicates the possibility of severe injuries if a
user operates the unit improperly.
Caution This indicates the possibility of minor injury or
damage if a user operates the unit improperly.
Danger This indicates the possibility of re, severe injury,
and even death if a user disregards the instruction
and operates the unit improperly.
Safety Requirements
Be sure to observe
！
● Limited Warranty
・We are not responsible for damages resulting from negligence through failure to follow
the instructions set out in this manual.
・We are not responsible for damages resulting from earthquake and/or fire unrelated to
us, actions by third parties, or any other accidents, intentional or through customer neg-
ligence, as well as from accidents caused by misuse or improper use under abnormal
conditions.
・For information regarding assurance provisions, please read the attached warranty certi-
cate.
！
！
Warning
！
Caution
！
・Do not look into the laser beam
・Do not point the laser beam at people
・Do not allow usage by children
Do not contact the laser beam irradiation port with a rotating body
Do not measure using wet or oily
hands, or with loosely tted clothing.
Be careful around installed reective
tape.
If the unit comes into contact with a rotating body,
damage may result to the laser.
The reection tape may come loose during high-speed
rotation.
If hands slip during measurement, fingers or part of
the hand may get caught in the rotating equipment.
● Enables measurement of a rotating body at a distance using
integral laser beam
● Maximum of 1000 data point storage
● The organic light emitting display (OLED) allows enhanced
viewing, even in dark locations
● Selectable meter or graphic display modes
● High accuracy measurement capability of +/-0.006%
● PC communication through USB with available software
■ Inspection result certicate
We skip issuance of the inspection result certicate for this product. However, at the
time of factory shipment total shipment inspection has been completed, and we have
strictly conrmed that there is no error in measurement accuracy and operation.Your
understanding is appreciated.
Non-contact type digital tachometers are used to perform
measurement by applying the supplied reflection tape
to the rotating body of the object to be measured, and
projecting the laser beam (red) to the tape. In addition,
they can be used for contact type measurement by
attaching the supplied contact adapter.
Handheld Digital Tachometer Non-contact type
with Dual Non-Contact, Contact Operation
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

1
INDEX
1. Part Names and Functions 2
2. Measurement Method 4
3. Measurement Display Description 6
4. Graph Display 8
5. Memory Function 9
5-1. Memory mode details 9
5-2.
Memory registration in the memory group 10
6. Various Settings 11
6-1. Contents selection 11
6-2. Memory data display 11
6-3. User settings 15
6-4. System settings 22
7. Battery Replacement 34
8. Dimensional Drawing 34
9. Specications 35
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

2
1. Part Names and Functions
(1) Laser beam irradiation port
(1) Operation key 1
(4) Operation key 4
(2) Operation key 2
(3) Operation key 3
(5) Power/Measurement key
(2) Display screen
(7) Mounting Adapter
(3) Operation keys
(8) Battery Compartment
(5) USB connector
Parts name Functions
(1) Laser beam
irradiation port
Apply the reection tape to the rotating body of the object to
be measured. Project the laser beam (red) to the tape and
measure the rotation speed.
(2) Display screen Displays the measurement value.
(3)
Operation keys 1 to 4
Used to change setting or store memory data.
(4) Power/
Measurement key
Press this key to turn the power ON.
The power will be turned OFF when no operation has been
performed for a certain period of time. (Auto o󱐯 function)
(5) USB connector Power can be supplied through the USB connector.
Also, connecting the unit to a PC enables communications
using using the available software. (Sold separately)
(6) Connector For internal production usage only
(7) Mounting Adapter Allows unit to be mounted with its x/x ? threaded connection
on tripod
(8)
Battery Compartment
Uses two AA dry cell batteries
Parts name Mode Function
(1)
Operation key 1
・ Measurement mode (measurement
standby, during measurement)
Used to store the memory data.
・Set mode Used to select the item.
・Memory data display mode Used to select the item.
(2)
Operation key 2
・ Measurement mode (measurement
standby, during measurement)
Used to display memory data,
and congure various settings.
・Set mode Used to select the item.
・Memory data display mode Used to select the item.
(3)
Operation key 3
・ Measurement mode (measurement
standby, during measurement)
Used to switch the measurement
display.
・Set mode Used as the enter key.
・Memory data display mode Used as the enter key.
(4)
Operation key 4
・ Measurement mode (measurement
standby, during measurement)
Used to return the measurement
display to the normal display.
・Set mode Used as the cancel key.
・Memory data display mode Used as the cancel key.
(5)
Power/
Measurement key
・When the power is OFF Used to turn the power ON.
・Measurement mode Used to perform measurement.
(4) Power/Measurement key
(6) Connector
■ Operation keys and power/measurement key details
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

3
*For screen protection, the display becomes dark when no operation has been performed for 10 seconds.
Also, the display is turned OFF when no operation has been performed for 1 minute.
■ Display screen details
■ OVER display
(2) Rotation detection display
(1) Main display
(3) Upper/lower limit judgment display
(4) Unit display
(5) Description display (6) Battery display
Key name
(1) Main display Displays the measurement value.
(2)
Rotation
detection display
Blinks during measurement.
"A" is displayed when the contact adapter has been
attached.
With contact Without contact
(3)
Upper/lower limit
judgment display
Displays judgment results of the display value
according to the comparator setting.
When the upper When the lower
limit is reached limit is reached
(4) Unit display Displays the current set unit.
(5)
Description display
Displays description for the measurement value currently indicated.
(6) Battery display Displays the remaining battery level.
Blinks when the remaining battery level becomes close to 0.
Also, the following mark is displayed when the power is supplied through the USB cable.
When the USB cable is connected
When the measured value exceeds the display range, "- - - - - -" is displayed.
Also, when it exceeds the measurement range, "OVER" is indicated in the unit display, and it blinks.
● Display range OVER ● Measurement range OVER
* When "OVER" is indicated, the measurement accuracy
is not guaranteed.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

4
* When the speed and distance units are selected in the unit setting, be sure to select "3. SET_SYSTEM" in contents selection, and set the
distance value per pulse in the "9. DIST/PULS" setting.
2. Measurement Method
Apply the supplied reflection tape to
the rotating body of the object to be
measured.
● Do not apply to a rotating body smaller
than the re ection tape.
● If the rotating body is glossy, apply black
tape, or paint it black and apply the
re ection tape.
● Before applying the reflection tape, wipe
off water/oil on the attachment surface
of the rotating body, and apply the tape
without any irregularities.
Press the power/measurement key, and start
measurement.
● When the rotating body is static, the value "0" is
displayed.
● When the rotating body rotates, the actual
measurement data is displayed every display update
cycle.
After measurement ends, the power is turned OFF when no operation has been performed for a certain period of time.
● The period of time until the power goes OFF can be set in "Auto o󱐯 " in the system settings.
● When performing communication using the optional USB cable, the auto o󱐯 function is disabled.
2
Point the laser beam irradiation
port to the object to be measured
3
Apply the re ection tape to
the object to be measured
1
Re ection tape
Press the power/measurement key
to start measurement
Power OFF when no operation has been performed for a certain period
of time (Auto o󱐯 function)
4
Final measurement
value held
Power OFF
Left unoperated
Point the laser beam irradiation port to
the re ection tape applied to the rotating
body.
● Keep a distance of 50 to 4000 mm (2 in.
to 13 ft.) between the reflection tape and
irradiation port.
■ Non-contact measurement
Laser beam
Power/Measurement key
Failure to follow this could result in injury to the eyes.
Never look into the laser beam.
Do not point the laser beam at people.
Do not allow usage by children.
■ Precautions on measurement and handling
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

5
■ Precautions on measurement and handling
When measuring a high-speed rotating body using the conical or funnel contact over a long period of time, note that the convex and concave
portions of the contact may produce high heat.
Before measurement, securely t the contact adapter to the contact. Also, during measurement, carefully put the contact on the rotating body of
the object to be measured.
When attaching the speed measurement wheel for measurement, align it along the object to be measured, and do not push the wheel with
excessive force. Also, for safety measurement, use with a speed of 300m/min (500cm/s, 18000m/h, ～ 18km/h, 197inch/s) or less.
For rotation speed measurement, attach
the conical or funnel contact.
● When the object to be measured has a
concave shaft, attach the conical contact.
● When the object to be measured has a
conical shaft, attach the funnel contact.
* When attaching the contact, securely fit
the measurement shaft pin into the contact
groove.
Carefully put the contact on the center of the
rotating body of the object to be measured.
Press the power/measurement key, and
start measurement.
Note) When attaching the wheel, securely t the
measurement shaft pin into the wheel groove.
* Select "4. Contact (Low)" when using the optional
contact adapter for low speed.
Select the appropriate
contact tting and attach.
Press the power/measurement
key, and start measurement
2
5
In the "5. CONTACT" setting of "3. SET_
SYSTEM" in contents selection, change
to "1. Contact" or "4. Contact (Low)"*.
3
Attach the contact
adapter
Attach the speed measurement
wheel to the measurement shaft
Press the power/measurement
key, and start measurement
Put the contact on the
object to be measured
1
1 3
4
Put the speed
measurement wheel
on the object to be
measured
2
Contact (conical)
Measurement
shaft pin
Power/Measurement key
Speed measurement wheel
Carefully put the speed
measurement wheel on the object
to be measured (belt part, etc.).
Refer to the above (rotation speed
measurement)
Measurement
shaft pin
■ Contact measurement
■ When using the speed measurement wheel
Attaching the optional contact adapter enables measurement in the contact mode.
*The auto o󱐯 function works similarly as in the case of non-contact measurement.
* When performing the non-contact measurement again after contact measurement ends, be sure to select "3. SET_SYSTEM"
in contents selection, and set to "1. Contact" in the "5. CONTACT" setting.
* When using the speed measurement wheel, in the "8. DIAMETER" setting of "3. SET_SYSTEM" in contents selection, set
the diameter value of the peripheral speed foil. When using the supplied speed measurement wheel (circumference of 6
inches), use it with the default value (diameter value of 48.5104 mm).
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

6
Display Description
Normal Description Displays the measurement value corresponding to the selected unit.
Display update Updates every display update cycle.
Maximum value
(Inactive during distance
and manual measurement)
Description Displays the maximum value from measurement start to end. This value is reset
when the next measurement starts.
Display update Updates every display update cycle.
Minimum value
(Inactive during distance
and manual measurement)
Description Displays the minimum value from measurement start to end.
This value is reset when
the next measurement starts, or the auto zero function is performed.
Display update Updates every display update cycle.
Average value
(Inactive during distance
and manual measurement)
Description Displays the average value within the "GRAPH_TIME" specied in the system
settings.
Display update Updates every "GRAPH_TIME".
Acceleration rate
(Inactive during distance
and manual measurement)
Description Displays the acceleration rate within the "GRAPH_TIME" specied in the system
settings.
Display update Updates every "GRAPH_TIME".
Prescale Description
Displays the measurement value when "PRESCALE" is enabled. This feature is selected
in the system settings. When "PRESCALE" is not specied, this is not displayed.
Display update Updates every display update cycle.
Prescale maximum value
(Inactive during distance
and manual measurement)
Description Displays the maximum value among the measurement values when "PRESCALE"
is enabled. This value is reset when the next measurement starts.
Display update Updates every display update cycle.
Prescale minimum value
(Inactive during distance
and manual measurement)
Description Displays the minimum value among the measurement values when "PRESCALE"
is enabled. This value is reset when the next measurement starts.
Display update Updates every display update cycle.
Prescale average value
(Inactive during distance
and manual measurement)
Description Displays the average value within the "GRAPH_TIME" specied in the system
settings, among the measurement values when "PRESCALE" is enabled.
Display update Updates every "GRAPH_TIME".
Prescale acceleration rate
(Inactive during distance
and manual measurement)
Description Displays the acceleration rate within the "GRAPH_TIME" specied in the system
settings, among the measurement values when "PRESCALE" is enabled.
Display update Updates every "GRAPH_TIME".
■ About calculation of the maximum value (MAX) and minimum value (MIN)
Press the operation key 3 in the measurement mode. The measurement value description to be displayed is switched.
The types of the measurement value to be displayed are as follows:
・ As shown in the gure below, the instrument sets the measurement value when measurement starts with initial values of MAX0 and MIN0.
It then compares them to new measurement values every sampling cycle.
New updated maximum and minimum values are created and displayed if they exceed (for MAX0) or are below (for MIN0).
(Updates in the order of MAX0 → MAX1 → MAX2)
・The maximum and minimum values are reset when measurement starts.
Time
Sampling cycle*1
MAX2
MIN2
Rotation speed
Measurement
start
Measurement
start
Measurement
end
Measurement
end
MAX2
MAX0
MIN0
MIN1
MAX1
MAX0
MIN0
MAX1
3. Measurement Display Description
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

7
■ About calculation of the average value (AVE)
■ About calculation of the acceleration rate (ACC)
The average value is displayed by averaging the measurement values in the corresponding cycle every average value update cycle.
The acceleration rate is calculated based on v0 and v1 in the corresponding cycle every acceleration rate update cycle.
Time
Sampling cycle*1
Average value update cycle*2
Average calculation of the
measurement display values 1 to 6
1
2 3
4
5 6 7
8
9
10
11 12
Average calculation of the
measurement display values 7 to 12
Rotation speed
Sampling cycle*1
MAX
MIN
Time
Acceleration rate update cycle*2
Gradient = Acceleration rate
Acceleration rate
calculation time
Acceleration rate =(v1 - v0)/Acceleration rate calculation time
v0
v1
Rotation speed
*1 The sampling cycle is "DISP_CYCLE" in the system settings.
*2 The average value update cycle and acceleration rate update cycle are "3-2 Graph time" in the system settings.
*The acceleration rate is displayed up to 5 digits, and when the speed is decreased, it is displayed as a negative value.
*Minus value of the acceleration value cannot be displayed in the graph.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

8
Using the "4. GRAPH_DISP" setting of "2. SET_USER" in contents selection enables the graph to be indicated on the display.
4. Graph Display
(1) Graph_1 (Line graph)
(2) Graph_2 (Gauge Mode)
(3) Graph_3 (Bar graph)
4) Graph time display (3) Measurement value display
(1) Various status display
(1) Various status display
(1) Various status display
(2) Line graph display
Parts name Operation
(1) Various status
display Same as in the normal display
(2) Line graph
display
Displays the line graph for the measurement value.
Depending on selection one of the below will equal
the graph values:
Maximum value on the vertical axis:
Graph maximum value setting
Minimum value on the vertical axis:
Graph minimum value setting
Horizontal axis: Graph time setting value
Graph ow: Graph ow setting value
(3) Measurement
value display
Displays the current measurement value
Can switch among MAX, MIN, AVE, and ACC
(4) Graph time
display Displays the graph time setting value
*Update cycle: Every display update cycle
Parts name Operation
(1) Various status
display Same as in the normal display
(2) Gauge Display Displays the needle graph for the measurement
value. Depending on selection one of the below will
equal the gauge values:
Graph maximum value:
Graph maximum value setting
Graph minimum value:
Graph minimum value setting
(3) Measurement
value display
Displays the current measurement value
Can switch among MAX, MIN, AVE, and ACC
(4) Graph maximum
value display Displays the graph maximum value setting
(5) Graph minimum
value display Displays the graph minimum value setting
*Update cycle: Every display update cycle
Parts name Operation
(1) Various status
display Same as in the normal display
(2) Bar graph display Displays the bar graph for the measurement value.
Depending on selection one of the below will equal
the gauge values:
Graph maximum value:
Graph maximum value setting
Graph minimum value:
Graph minimum value setting
(3) Measurement
value display
Displays the current measurement value
Can switch among MAX, MIN, AVE, and ACC
(4) Graph maximum
value display Displays the graph maximum value setting
(5) Graph minimum
value display Displays the graph minimum value setting
*Update cycle: Every display update cycle
(3) Measurement
value display
(3) Measurement
value display
(5) Graph minimum
value display
(5) Graph minimum
value display
(4) Graph maximum
value display
(4) Graph maximum
value display
(2) Needle graph display
(2) Bar graph display
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

9
The measurement value can be registered and stored in the memory during measurement.
The stored data can be displayed in contents selection "1. DATA".
Registration contents and methods depend on the memory mode.
Set the memory mode in the "2. MEMORY_MODE" of "2. SET_USER" in contents selection.
・In the continuous memory mode, the measurement value continues to be registered in the memory every display update cycle.
・The number of memory sets that can be registered in the continuous memory is up to 1000.
・For the continuous memory, the value description to be registered in the memory depends on the measurement display description.
・In the each memory mode, only one set of the measurement value currently displayed is registered in the memory.
・The number of data points that can be registered in the each memory is up to 100.
・Press the Operation key 1 once during measurement to start memory registration. Press it again to end memory registration.
・When turning measurement OFF, or switching to the contents selection mode during memory registration, memory registration ends at
that moment.
・The unit and "Gr ○ _ □□□□ " are alternately displayed in the unit display part during memory registration.
( ○ shows the number of memory groups, and □ shows the number of memory points currently registered: 0001 to 1000)
・Press the operation key 1 once during measurement to register the display value at that moment in the memory.
・"Gr ○ _ □□□□ " is displayed for 1 second in the unit display part during memory registration.
( ○ shows the number of memory groups, and □ shows the number of memory sets currently registered: 001 to 100)
5. Memory Function
5-1 Memory mode details
(1) Continuous memory mode
(2) Each memory mode
● Memory registration operation
● Memory registration operation
・Normal display
・MAX display
・MIN display
・AVE display
・ACC display
・PRE display
・P.MAX display
・P.MIN display
・P.AVE display
・P.ACC display
Registers the measurement value every display update cycle
Registers the measurement value every display update cycle after prescale calculation
Displayed alternately every second during memory registration
Displayed for 1 second during memory registration
Operation key 1:
Memory registration start/end
Operation key 1:
Performs memory registration
*The continuous memory mode can be used only when one of the units from "rev/min" to "miles/h" is selected in the unit setting.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

10
・In the statistics memory mode, only the statistics data for the measurement value every display update cycle from memory registration
start to end is registered in the memory.
・The number of data points that can be registered in the statistics memory is up to 100.
・Start memory registration from the start memory group (that has been set in "3. START_MEM" of "2. SET_USER" in contents selection).
・When the number of memory groups reaches the number of memory sets in each group (that has been set in "4. MEM_GROUP" of "3.
SET_SYSTEM" in contents selection), the memory group switches to the next one.
・When the number of memory sets exceeds the total number of memory sets for all memory groups, "FULL" is displayed in the unit
display part. In this case, additional memory cannot be registered.
・Press the operation key 1 once during measurement to start memory registration, and press it again to end memory registration.
・ When turning measurement OFF, or switching to the contents selection mode during memory registration, memory registration ends at
that moment.
・The unit and "Gr ○ _ □□□□ " are alternately displayed in the unit display part during memory registration.
( ○ shows the number of memory groups, and □ shows the number of memory sets currently registered: 001 to 100)
(3) Statistics memory mode
● Memory registration operation
Example: When the start memory group is set to memory group 2
Group 1 Group 2 Group 3 Group 5Group 4
Displayed alternately every second during memory registration
(1) Start memory registration
from the start memory group
(2) Go to the next memory group
when the number of memory
sets exceeds the specied
number
(3) Go to the next memory
group when the number
of memory sets is 0
(4) Return to memory group 1
when the number of memory
sets exceeds the specied
number in group 5
(5) Displays "FULL" when the number of memory sets exceeds the specified number for all
memory groups, and ends memory registration ("FULL" is displayed until the operation key
1 is pressed)
After that, even if you press the operation key 1 and try to start memory registration, "FULL"
is displayed for 1 second, and registration is disabled.
Operation key 1:
Memory registration start/end
* In the statistics memory mode, the statistics data in a single registration is calculated from the measurement value for up to 100 times
of display update. When the display update frequency exceeds 100 in a single registration, memory registration automatically ends.
*The statistics memory mode can be used only when one of the units from "rev/min" to "miles/h" is selected in the unit setting.
5-2. Memory registration in the memory group
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

11
Press the operation key 2 in the measurement mode to switch the display to the contents selection mode.
The memory data registered for each group can be checked in contents selection "1. DATA".
6. Various Settings
6-1. Contents selection
6-2. Memory data display
English Japanese
[SET_CONTENTS]
DATA
SET_USER
SET_SYSTEM
[選択してください]
メモリ表示
ユーザー設定
システム設定
Item Description
English Japanese
1 DATA メモリ表示 Go to the memory display
2 SET_USER ユーザー設定 Go to the user settings
3 SET_SYSTEM システム設定 Go to the system settings
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Go to the selected item
Operation key 4 Return to the measurement
mode
Display the memory data according to the following operation.
(1) Operation ow
[選択してください]
メモリ表示
ユーザー設定
システム設定
[連続メモリ]
1．グループ_1
2．グループ_2
3．グループ_3
[単独メモリ グループ 1]
UNIT : rev/min
MAX : 100.00
MIN : 10.12
Measurement mode
During measurement
During measurement standby Turn the operation
key 2 ON
Turn the operation
key 3 ON
Use the operation keys 1 and 2 to select
the memory group to be displayed
Memory data display
Contents selection
Select [1. DATA], and turn
the operation key 3 ON
[SET_CONTENTS]
1. DATA
2. SET_USER
3. SET_SYSTEM
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

12
English
English
English
Japanese
Japanese
Japanese
Item Description
English Japanese
1. Group_1 グループ _1 Displays memory group 1
2. Group_2 グループ _2 Displays memory group 2
3. Group_3 グループ _3 Displays memory group 3
4. Group_4 グループ _4 Displays memory group 4
5. Group_5 グループ _5 Displays memory group 5
Item Description
English Japanese
1 No いいえ
Does not clear, and returns to the continuous memory display
2Yes はい Clears the continuous memory description
Display item Description
UNIT： Unit
MAX： Maximum value
MIN： Minimum value
AVE： Average
SD： Standard deviation
1 blank line
1: ～
1000：
Displays the memory registration value
for 1 to 1000 sets (max.)
CLEAR Go to memory clear
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Go to memory description
display
Operation key 4 Return to contents selection
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Enabled when CLEAR is
selected
Go to memory clear
Operation key 4 Return to memory group
selection
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Execute clear/Return to the
continuous memory display
without executing clear
Operation key 4 Return to the continuous
memory display
Select the memory group you want to display.
Select the memory group in (1), and press the operation key 3 to display the memory data for the selected memory group.
Use the operation keys 1 and 2 to change the display line.
While the memory data is displayed, the "CLEAR" column is displayed in the last line of the data.
Select the "CLEAR" column, and press the operation key 3 to display the memory clear screen below.
Registration description in the memory group currently displayed can be cleared as necessary.
Select "1. DATA" in contents selection to display the memory group selection screen.
(2) Memory data display/details
(1) Memory group selection
(2) Memory data display
(3) Memory clear
● Continuous memory display
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

13
English
English
Japanese
Japanese
Item Description
English Japanese
1 Group_1 グループ _1 Displays memory group 1
2 Group_2 グループ _2 Displays memory group 2
3 Group_3 グループ _3 Displays memory group 3
4 Group_4 グループ _4 Displays memory group 4
5 Group_5 グループ _5 Displays memory group 5
Item Description
English Japanese
1. No いいえ
Does not clear, and returns to the each memory display
2. Yes はい Clears the each memory description
Display item Description
UNIT： Unit
MAX： Maximum value of the registration data
MIN： Minimum value of the registration data
AVE： Average of the registration data
SD： Standard deviation of the registration data
1 blank line
1: ～
100：
Displays the memory registration value for 1 to
100 sets (max.)
CLEAR Go to memory clear
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Go to the memory data display
Operation key 4 Return to contents selection
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Enabled when CLEAR is
selected
Go to memory clear
Operation key 4 Return to memory group
selection
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Execute clear/Return to the
each memory display without
executing clear
Operation key 4 Return to the each memory
display
Select the memory group you want to display.
Select the memory group in (1), and press the operation key 3 to display the memory data for the selected memory group.
Use the operation keys 1 and 2 to change the display line.
While the memory data is displayed, the "CLEAR" column is displayed in the last line of the data.
Select the "CLEAR" column, and press the operation key 3 to display the memory clear screen below.
Registration description in the memory group currently displayed can be cleared as necessary.
Select "1. DATA" in contents selection to display the memory group selection screen.
(1) Memory group selection
(2) Memory data display
● Each memory display
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

14
English Japanese
Item Description
English Japanese
1 Group_1 グループ _1 Displays memory group 1
2 Group_2 グループ _2 Displays memory group 2
3 Group_3 グループ _3 Displays memory group 3
4 Group_4 グループ _4 Displays memory group 4
5 Group_5 グループ _5 Displays memory group 5
Display item Description
No: 1 - 100
UNIT: Unit
MAX： Maximum value
MIN： Minimum value
AVE： Average
SD： Standard deviation
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Go to memory description
display
Operation key 4 Return to contents selection
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Enabled when CLEAR is
selected
Go to memory clear
Operation key 4 Return to memory group
selection
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Execute clear/Return to the
statistics memory display
without executing clear
Operation key 4 Return to the statistics memory
display
Operation key Operation
Operation key 1 Disabled
Operation key 2 Return to No. 1
Operation key 3 Go to memory clear
Operation key 4 Return to contents selection
Select the memory group you want to display.
Select the memory group in (1), and press the operation key 3 to display the memory data for the selected memory group.
Use the operation key 1 to change the display line.
Use the operation key 2 to display the description of the next registration memory.
Select "1. DATA" in contents selection to display the memory group selection screen.
(1) Memory group selection
(2) Memory data display
(3) Memory clear
● Statistics memory display
English
English
Select CLEAR in the following item of the last No.
English
Japanese
Japanese
Japanese
Item Description
English Japanese
1 No いいえ
Does not clear, and returns to the each memory display
2Yes はい Clears the statistics memory description
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

15
6-3. User settings
Go to the user setting mode in the following operation.
Select the item to set in the following item selection screen, and perform detailed settings.
(1) Operation ow
(2) User settings - Setting item selection
[ユーザー設定]
コンパレータ
メモリモード
開始メモリ
[選択してください]
メモリ表示
ユーザー設定
システム設定
Measurement mode
During measurement
During measurement standby
Go to the user settings
Contents selection
2. User settings mode
selection
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Go to the detail settings of the
selected item
Operation key 4 Return to the Contents
selection
English Japanese
[SET_CONTENTS]
1. DATA
2. SET_USER
3. SET_SYSTEM
[SET_USER]
1. COMPARATOR
2. MEMORY_MODE
3. START_MEM
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

16
● List of the user settings
Item
type
Item
number
Main item title Item
number
Sub item title Setting description Default
value Remark
English Japanese English Japanese English Japanese
User
settings
1 COMPARATOR コンパレータ
1-1 UPPER_LIMIT 上限値 0.00000 ～ 999999 0.00000
6-digit numerical value
setting with decimal point
1-2 LOWER_LIMIT 下限値 0.00000 ～ 999999 0.00000
2 MEMORY_MODE メモリモード ー
Cont 連続
Cont ーEach 単独
Stats 統計
3
START_MEM 開始メモリ ー
Group_1 グループ _1
Group_1 ー
Group_2 グループ _2
Group_3 グループ _3
Group_4 グループ _4
Group_5 グループ _5
4 GRAPH_DISP グラフ表示 ー
Normal 通常表示
Normal ー
Graph_1 グラフ 1
Graph_2 グラフ 2
Graph_3 グラフ 3
5 SAVE 設定保存
5-1 SEL_USER
設定グループ
User □ Set_1 設定 _1
ー ー
User □ Set_2 設定 _2
User □ Set_3 設定 _3
5-2 R/W 読出 / 保存 Used 読出 ー ー
Over □ Write 保存
6 UNIT 単位 ー
rev/min
rev/min ー
m/min
cm/min
inch/min
feet/min
yards/min
rev/sec
m/sec
cm/sec
inch/sec
km/h
cm
m
km
inch
feet
yards
STP
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

17
[ 1-2．LOWER_LIMIT ]
[ 1-2．下限値 ]
[ 1-2．下限値 ]
[ 1-2．下限値 ]
[ 1-2．下限値 ]
[ 1-1．UPPER_LIMIT ]
[ 1-1．上限値 ]
[ 1-1．上限値 ]
[ 1-1．上限値 ]
[ 1-1．上限値 ]
(3) Detail settings for each item
(3-1) Comparator setting
(1) Upper limit value
(2) Lower limit value
In the "COMPARATOR" setting, set the UPPER_LIMIT and LOWER_LIMIT.
Compare UPPER_LIMIT and LOWER_LIMIT with the measurement display value, and display the judgment result in the screen.
・UPPER_LIMIT ≧ Measurement display value ≧ LOWER_LIMIT : OK judgment
・UPPER_LIMIT < Measurement display value : NG judgment
・LOWER_LIMIT > Measurement display value : NG judgment
Operation
key
Operation
When setting the numerical value When setting the decimal point
Operation
key 1
Increases the numerical
value in the selected digit
Press and hold for 1 second
to increase continuously
Return to the numerical
value setting
Operation
key 2 Moves the digit
Press and hold for 1 second
to move continuously
Moves the decimal point
Press and hold for 1 second
to move continuously
Operation
key 3 Go to 1-2
Operation
key 4 Return to the user setting
Operation
key
Operation
When setting the numerical value When setting the decimal point
Operation
key 1
Increases the numerical
value in the selected digit
Press and hold for 1 second
to increase continuously
Return to the numerical
value setting
Operation
key 2 Moves the digit
Press and hold for 1 second
to move continuously
Moves the decimal point
Press and hold for 1 second
to move continuously
Operation
key 3 Enables the setting, and returns to the user settings.
Operation
key 4 Return to 1-1
English
English
Japanese
Japanese
Go to the rst digit of the numerical value setting
Go to the rst digit of the numerical value setting
Moves
the digit
Moves
the digit
Decimal point
setting
Decimal point
setting
The selected
digit blinks ▲：The value in the selected
digit increases 0 - 9
▲：The value in the selected
digit increases 0 - 9
The blinking decimal point moves
by ▶
The blinking decimal point moves
by ▶
The selected
digit blinks
The continuous memory mode can be used only when one of "rev/min" to "km/h" is selected in the unit setting.
*
When both "UPPER_LIMIT" and "LOWER_LIMIT" are 0, judgment will be disabled, and the upper and lower limit judgment is not performed.
*The display value is judged.
*Values that represent UPPER_LIMIT<LOWER_LIMIT cannot be set.
[1-1. UPPER_LIMIT] [1-1. UPPER_LIMIT] [1-1. UPPER_LIMIT]
[1-2. LOWER_LIMIT] [1-2. LOWER_LIMIT] [1-2. LOWER_LIMIT]
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

18
(3-2) Memory mode
Set the memory mode.
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Go to memory clear
Operation key 4 Return to the user setting
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Execute clear/Return to the
memory mode setting without
executing clear
Operation key 4 Return to the memory mode
setting
English
English
Japanese
Japanese
Item Description
English Japanese
1 Cont 連続メモリ Continuous memory mode
2 Each 単独メモリ Each memory mode
3 Stats 統計メモリ Statistics memory mode
When changing the memory mode, the memory data currently registered will be cleared.
When selecting "2. Yes" in the conrmation screen below, the memory data will be cleared.
When selecting "1. No", the change will not be reected, and the display will return to the previous screen.
* When changing the memory mode, the setting value of the number of registered memory sets for each memory group ("4. MEM_
GROUP" of "3. SET_SYSTEM" in contents selection) is initialized to the value that corresponds to the memory mode.
Memory clear conrmation
Item Description
English Japanese
1 No いいえ
Memory data all clear not permitted
2Yes はい Memory data all clear permitted
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

19
(3-3) Start memory group setting
(3-4) Graph display
Select the memory group to start memory registration.
The display can be switched to the graph display.
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Enable the selected item, and
return to the user settings.
Operation key 4 Return to the user setting
Operation key Operation
Operation key 1 Select the upper item
Press and hold for 1 second to
move continuously
Operation key 2 Select the lower item
Press and hold for 1 second to
move continuously
Operation key 3 Enable the selected item, and
return to the user settings.
Operation key 4 Return to the user setting
English
English
Japanese
Japanese
Item Description
English Japanese
1 Group_1 グループ 1 Species the memory group to start memory
registration as group 1
2 Group_2 グループ 2 Species the memory group to start memory
registration as group 2
3 Group_3 グループ 3 Species the memory group to start memory
registration as group 3
4 Group_4 グループ 4 Species the memory group to start memory
registration as group 4
5 Group_5 グループ 5 Species the memory group to start memory
registration as group 5
Item Description
English Japanese
1 Normal 通常表示 Display change: Normal display
2 Graph_1 グラフ _1 Display change: Graph 1 (Line graph)
3 Graph_2 グラフ _2 Display change: Graph 2 (Needle graph)
4 Graph_3 グラフ _3 Display change: Graph 3 (Bar graph)
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]