Shin Chuan Computer SC800 User manual

Shin Chuan Computer
User’s Manual
SC800/SC820
SC800/SC820 User’s Manual
WinCE Rugged Portable Data Terminal
July/10/2009 Ver: 1.0

Shin Chuan Computer
User’s Manual
SC800/SC820
Revision History:
Date Description Remark
2008/12/18 Modified the contents of ch.3 and Appendix A GPRS Function
2009/2/16 Modified the contents of 2.5.8 Installing the SD Card
2009/6/16 Added Appendix B Expansion Module Applicability(RFID, GPS)
2009/6/19 Added “ Note: Wireless LAN, 2.4GHz Low Power Hyper and
GPRS/EDGE cannot be used at the same time.” on Page 1-9
2009/7/10 Added Appendix C 2D Barcode Scanner Setting
2009/07/15 Added SAR Statement for FCC Certificate

Shin Chuan Computer
User’s Manual
SC800/SC820
Table of Contents
Chapter 1. Introduction ............................................................................1-1
1.1 About this Manual.................................................................1-1
1.2 User and Product Safety ......................................................1-2
1.3 Battery Safety.......................................................................1-3
1.4 CE Statement .......................................................................1-4
1.4.1 Europe – EU Declaration of Conformity.......................1-4
1.5 FCC Statement.....................................................................1-8
1.5.1 FCC Interference Statement ........................................1-8
1.5.2 Hand-Operated Device SAR Evaluation: .....................1-9
1.6 Recycling & disposal instructions. ......................................1-10
1.7 Regulatory information. ......................................................1-10
1.8 Product Labeling ................................................................1-11
1.9 System Specifications ........................................................1-15
1.10 Environment Standard......................................................1-17
1.11 Warranty and after service................................................1-17
Chapter 2. Getting Started........................................................................2-1
2.1 Check the package...............................................................2-1
2.2 General View of the PDT......................................................2-3
2.2.1 SC800 general view.....................................................2-3
2.2.2 SC820 general view.....................................................2-5
2.3 Charging the Battery Pack ...................................................2-7
2.3.1 Installing the battery pack ............................................2-7
2.3.2 Charging the battery pack with Power Adapter ............2-9
2.4. Handling the PDT..............................................................2-10
2.4.1 Starting the PDT.........................................................2-10
2.4.2 Power on / off.............................................................2-10
2.4.3 Calibration of the touch Screen..................................2-11
2.4.4 To mute the Sound for SC800....................................2-11
2.4.5 Adjusting the Sound for SC820..................................2-11
2.4.6 Using the Stylus .........................................................2-12
2.4.7 Using the SC800 Keypad...........................................2-12
2.4.8 Using the SC820 Keypad...........................................2-14
2.4.9 Using the Ear/Microphone .........................................2-17

Shin Chuan Computer
User’s Manual
SC800/SC820
2.5 Navigating the Display........................................................2-18
2.5.1 Setting Time and Date ...............................................2-18
2.5.2 Entering the Data.......................................................2-18
2.5.3 The Command Bar.....................................................2-19
2.5.4 The Task Bar..............................................................2-19
2.5.5 The Soft Keypad ........................................................2-20
2.5.6 Setting Up Wireless LAN ...........................................2-20
2.5.7 Reading barcodes, 1D laser version..........................2-26
2.5.8 Reading barcodes, 2D CMOS version.......................2-27
2.5.9 Installing the SD Card ................................................2-29
2.5.10 Help .........................................................................2-30
2.6 Power management ...........................................................2-30
2.6.1 Suspend Mode...........................................................2-30
2.6.2 Resuming...................................................................2-31
2.7 Resetting the PDT..............................................................2-31
2.7.1 Software (Warm) Reset..............................................2-31
2.7.2 Cold Reset .................................................................2-32
Chapter 3. Setting .....................................................................................3-1
3.1 Introduction ..........................................................................3-1
3.2 Control Panel .......................................................................3-1
3.2.1 BarCode Setting...........................................................3-1
3.2.2 Symbologies List..........................................................3-7
3.2.3 Bluetooth Device Properties ......................................3-23
3.2.4 Certificates.................................................................3-27
3.2.5 Control Center............................................................3-29
3.2.6 Date/Time ..................................................................3-34
3.2.7 Dialing Properties.......................................................3-34
3.2.8 Display Properties......................................................3-36
3.2.9 Input Panel.................................................................3-38
3.2.10 Internet Options .......................................................3-39
3.2.11 Keyboard..................................................................3-41
3.2.12 Network and Dial-up Connections............................3-42
3.2.13 Owner ......................................................................3-46
3.2.14 Password .................................................................3-48
3.2.15 PC Connection.........................................................3-48
3.2.16 Power.......................................................................3-49
3.2.17 Regional Settings.....................................................3-52

Shin Chuan Computer
User’s Manual
SC800/SC820
3.2.18 Remove Programs...................................................3-52
3.2.19 Storage Manager .....................................................3-53
3.2.20 Stylus .......................................................................3-54
3.2.21 System.....................................................................3-56
3.2.22 Terminal Server Client Licenses..............................3-58
3.2.23 Volume & Sounds Properties ...................................3-58
3.3 Taskbar and Start Menu .....................................................3-59
Chapter 4. Communication ......................................................................4-1
4.1 Installing & Setting Up Microsoft ActiveSync ........................4-1
4.1.1 Installing Microsoft ActiveSync on the Host PC............4-1
4.1.2 Connecting PDT to Host PC ........................................4-1
4.2 Using ActiveSync .................................................................4-1
4.2.1 Setting up a Partnership ..............................................4-1
4.2.2 ActiveSync File Synchronization ..................................4-3
4.3 Networking ...........................................................................4-3
Chapter 5. Software Applications............................................................5-1
5.1 Introduction ..........................................................................5-1
5.2 Software Applications...........................................................5-1
5.2.1 Inbox............................................................................5-1
5.2.2 Internet Explorer ........................................................5-11
5.2.3 Messenger .................................................................5-14
5.2.4 Microsoft WordPad ....................................................5-14
5.2.5 Remote Connection ...................................................5-20
5.2.6 Windows Explorer......................................................5-21
5.3 DiskOnChip ........................................................................5-23
5.3.1 Saving to Flash ..........................................................5-23
5.3.2 DiskOnChip Location .................................................5-23
5.3.3 DiskOnChip Size........................................................5-24
Appendix A GPRS Function ..................................................................... A-1
A.1 Using the GPRS Features .................................................. A-1
A.1.1 SIM Card .................................................................... A-1
A.1.2 Inserting a SIM Card................................................... A-1
A.1.3 Before Start: ............................................................... A-2
A.2 Select settings .................................................................... A-4
A.3 Internet connection ............................................................. A-8

Shin Chuan Computer
User’s Manual
SC800/SC820
A.3.1 Connecting ................................................................. A-8
Appendix B Expansion Module Applicability.......................................... B-1
B.1 RFID Applicability................................................................ B-1
B.2 GPS Applicability ................................................................ B-3
Appendix C 2D Barcode Scanner Setting ............................................... C-1
C.1 Basic Tab ............................................................................ C-1
C.2 Code Configure Tab............................................................ C-1
C.3 Prefix and Suffix Tab........................................................... C-2
C.4 Quiet Zone Tab ................................................................... C-3
C.5 Read Mode Tab .................................................................. C-3
C.6 ASCII Conversion Tab......................................................... C-4
C.7 Advanced Tab ..................................................................... C-4
C.8 Firmware Upgrade Tab ....................................................... C-5

Shin Chuan Computer
User’s Manual
SC800/SC820
1-1
Chapter 1.Introduction
Congratulations on purchasing the SC800/SC820 Portable Data Terminal (PDT),
a Microsoft Windows®CE Rugged PDT. Its special combination of features
makes it perfect for using in a wide range of applications. These features as:
Intel® XScaleTM PXA270 520MHz 32 bits RISC Processor
Windows® CE 5.0 Operating System
128MB SDRAM & 256MB/1GB Flash ROM
Open Architecture: User Accessible SD Slot
240 x 320, 3.5” Color TFT Display with Touch Panel
One Numeric-Alpha Keyboards with LED backlight
802.11b/g Radio Support
2.4GHz Low Power Hyper: V2.0+EDR, Class II Support
IrDA Support
Optionally Built-in GPRS/EDGE Module
Integrated 1D Barcode Scanner
Integrated 2D Barcode Scanner
1.1 About this Manual
The following chapters contained in this manual are:
Chapter 1: Introduction General information about the PDT.
Chapter 2: Getting started Describe the basic use of the PDT.
Chapter 3: Setting Provide basic instructions for
customizing the PDT.
Chapter 4: Communication Describe how to use all kinds of
communication of the PDT.
Chapter 5: Software Application Describe the installed applications on
the PDT.
Appendix A.
Appendix B
Appendix C
GPRS Function
Expansion Module
Applicability
2D Barcode Scanner
Setting
Provide instructions for the GPRS
Service
Provide instructions for the Expansion
Module Applicability
Provide instructions for the 2D Barcode
Scanner

Shin Chuan Computer
User’s Manual
SC800/SC820
1-2
1.2 User and Product Safety
zDo not stare into the laser or LED beam directly or shine it into eyes.
zNever use strong pressure onto the screen or subject it to severe impact,
as the LCD panel could become cracked and possibility cause personal
injury. If the LCD panel is broken, never touch the liquid inside because
the liquid irritates the skin.
zAlthough the PDT has passed the test of IP65 standard for water and dust
resistance, avoid prolonged exposure to rain or other concentrated
moisture. Such condition exceeds the IP65 standard, and could result in
water or other contaminants entering into the PDT.
zUse only the original approved AC Adapter with the PDT. Use of an
unapproved AC Adapter could result in electrical problems, or even cause
a fire or electrical shock to the user.
zDo not disassemble the PDT. Servicing should be done by supplier only. If
the PDT or accessories gets damaged due to wrong handling or
unauthorized repair, warranty is void. In case the warranty seals are
broken, warranty is void too.
zMake regularly back-up of all important data.
zUnder no circumstance will supplier be liable for any direct, indirect,
consequential or incidental damages baring out of the use or inability to
use the hardware and software and/or any data loss, even if supplier has
been informed about the possibility of such damages.
zLASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER
PRODUCT

Shin Chuan Computer
User’s Manual
SC800/SC820
1-3
1.3 Battery Safety
CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type.
Dispose of Used Batteries According to the Instructions.
Lithium-ion battery packs might get hot, explode, ignite and/or cause serious
injury if exploded by abusive using. Please follow the safety warnings listed as
below:
zDo not throw the battery pack in fire. Do not expose the battery to high
temperatures.
zDo not connect the positive battery pack with negative battery pack to
each other with any metal object (like wire).
zDo not carry or store battery pack together with metal objects.
zDo not pierce the battery pack with nails or drills, strike the battery pack
with a hammer, step on the battery pack or otherwise expose it to strong
impacts, shocks or excessive force.
zDo not solder onto the battery pack.
zDo not expose battery pack to liquid or allow the battery contacts to get
wet.
zDo not disassemble or modify the battery pack. The battery pack contains
safety and protection measures, which, if damaged, may cause the
battery pack to generate heat, explode or ignite.
zDo not discharge the battery pack using any device except for the
specified device. When it is used in devices other than the specified
devices, the battery pack can be damaged or its life expectancy reduced.
If the device causes any abnormal current to flow, it may cause the battery
pack to become hot, explode or ignite and cause serious injury.
zIn the event the battery pack leaks and the fluid gets into one’s eye, do not
rub the eye. Rinse well with water and immediately seek medical care. If
left untreated, the battery fluid could cause damage to the eye.

Shin Chuan Computer
User’s Manual
SC800/SC820
1-4
1.4 CE Statement
1.4.1 Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC. The following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the R&TTE
Directive 1999/5/EC:
- EN 60950-1: 2006
Safety of Information Technology Equipment
- EN50360 : (2001-07)
Product standard to demonstrate the compliance of mobile phones with the
basic restrictions related to human exposure to electromagnetic fields (300
MHz-3GHz)
- EN50361 : (2001-07)
Basic standard for the measurement of specific absorption rate related to
human exposure to electromagnetic fields from mobile phones (300 MHz-3
GHz)
- EN50371 : (2002-03)
Generic standard to demonstrate the compliance of low power electronic
and electrical apparatus with the basic restrictions related to human
exposure to electromagnetic fields (10 MHz-300 GHz) -- General public
- EN 300 328 V1.7.1: (2006-10)
Electromagnetic compatibility and Radio spectrum Matters (ERM);
Wideband Transmission systems; Data transmission equipment operating
in the 2,4 GHz ISM band and using spread spectrum modulation
techniques; Harmonized EN covering essential requirements under article
3.2 of the R&TTE Directive
- EN 301 511 V9.0.2: (2003-03)
Global System for Mobile communications (GSM); Harmonized standard
for mobile stations in the GSM 900 and DCS 1800 bands covering essential
requirements under article 3.2 of the R&TTE directive (1999/5/EC)

Shin Chuan Computer
User’s Manual
SC800/SC820
1-5
- EN 301 489-1 V1.6.1: (2005-09)
Electromagnetic compatibility and Radio Spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common technical requirements
- EN 301 489-17 V1.2.1 (2002-08)
Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 17: Specific conditions for 2,4 GHz wideband transmission
systems and 5 GHz high performance RLAN equipment
- EN 301 489-7 V1.2.1: (2002-08)
ElectroMagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment ad
services; Part 7: Specific conditions for mobile and portable radio and
ancillary equipment of digital cellular radio telecommunications systems
(GSM and DCS)
This device is a 2.4 GHz wideband transmission system (transceiver),
intended for use in all EU member states and EFTA countries, except in France
and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum
authorities in order to obtain authorization to use the device for setting up
outdoor radio links and/or for supplying public access to telecommunications
and/or network services.
This device may not be used for setting up outdoor radio links in France and in
some areas the RF output power may be limited to 10 mW EIRP in the
frequency range of 2454 – 2483.5 MHz. For detailed information the end-user
should contact the national spectrum authority in France.
0560
Česky
[Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve
shoděse základními požadavky a dalšími příslušnými
ustanoveními směrnice 1999/5/ES.

Shin Chuan Computer
User’s Manual
SC800/SC820
1-6
Dansk
[Danish]
Undertegnede [fabrikantens navn] erklærer herved, at
følgende udstyr [udstyrets typebetegnelse] overholder de
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät
[Gerätetyp] in Übereinstimmung mit den grundlegenden
Anforderungen und den übrigen einschlägigen Bestimmungen
der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer]
seadme [seadme tüüp = type of equipment] vastavust direktiivi
1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele
teistele asjakohastele sätetele.
English Hereby, [name of manufacturer], declares that this [type of
equipment] is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que
el [clase de equipo] cumple con los requisitos esenciales y
cualesquiera otras disposiciones aplicables o exigibles de la
Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ
[type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ
ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente [nom du fabricant] déclare que l'appareil [type
d'appareil] est conforme aux exigences essentielles et aux
autres dispositions pertinentes de la directive 1999/5/CE.
Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo
[tipo di apparecchio] è conforme ai requisiti essenziali ed alle
altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo [name of manufacturer / izgatavotāja nosaukums]
deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas
1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem
noteikumiem.
Lietuvių
[Lithuanian]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type]
atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos
nuostatas.
Hierbij verklaart [naam van de fabrikant] dat het toestel [type

Shin Chuan Computer
User’s Manual
SC800/SC820
1-7
Nederlands
[Dutch]
van toestel] in overeenstemming is met de essentiële eisen en
de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel
tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma
provvedimenti oħrajn relevanti li hemm fid-Dirrettiva
1999/5/EC.
Magyar
[Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel
a vonatkozó alapvetõ követelményeknek és az 1999/5/EC
irányelv egyéb elõírásainak.
Polski
[Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu]
jest zgodny z zasadniczymi wymogami oraz pozostałymi
stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português
[Portugues
e]
[Nome do fabricante] declara que este [tipo de equipamento]
está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z
bistvenimi zahtevami in ostalimi relevantnimi določili direktive
1999/5/ES.
Slovensky
[Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa
základné požiadavky a všetky príslušné ustanovenia Smernice
1999/5/ES.
Suomi
[Finnish]
[Valmistaja = manufacturer] vakuuttaa täten että [type of
equipment = laitteen tyyppimerkintä] tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien
direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I
överensstämmelse med de väsentliga egenskapskrav och
övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.

Shin Chuan Computer
User’s Manual
SC800/SC820
1-8
1.5 FCC Statement
1.5.1 FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation. Complies with 21 CFR
1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50,
dated June 24, 2007.
IMPORTANT NOTE:
For body worn operation, this phone has been tested and meets the FCC RF
exposure guidelines when used with the (Shin Chuan Computer Co., Ltd.)
accessories supplied or designated for this product. Use of other accessories
may not ensure compliance with FCC RF exposure guidelines.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating

Shin Chuan Computer
User’s Manual
SC800/SC820
1-9
instructions for satisfying RF exposure compliance. To maintain compliance
with FCC RF exposure compliance requirements, please follow operation
instruction as documented in this manual.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter except built-in tested devices.
The availability of some specific channels and/or operational frequency bands
are country dependent and are firmware programmed at the factory to match
the intended destination. The firmware setting is not accessible by the end
user.
Note: Wireless LAN, 2.4GHz Low Power Hyper and GPRS/EDGE cannot
be used at the same time.
Caution: SCC declares that SC800 ( FCC ID: TQ2-SC800PDT-BWG ) /
SC820 ( FCC ID: TQ2-SC800PDT-BWG ) is limited in CH1~CH11 for
2.4GHz by specified firmware controlled in U.S.A.
The FCC ID of SC800/SC820 is TQ2-SC800PDT-BWG
1.5.2 Hand-Operated Device SAR Evaluation:

Shin Chuan Computer
User’s Manual
SC800/SC820
1-10
LED AND LASER SAFETY INFORMATION
zClass I LED/ Class II Laser Product
zDo not stare at the LED/Laser or shine into eyes
zDo not allow young children to use the product without adult supervision
zDo not replace/repair the LED/Laser, these are not user replaceable
zDo not shine the LED/Laser on a shiny reflective surface
zLASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER
PRODUCT
1.6 Recycling & disposal instructions.
Do not throw this product in the home waste bin.
1.7 Regulatory information.
For CE, FCC, RoHS and other Document of Conformities, consult
the Contact Window of Shin Chuan Computer.

Shin Chuan Computer
User’s Manual
SC800/SC820
1-11
1.8 Product Labeling
The PDT has several labels as showed in Figure 1-1 to 1-4.
A. SC800
Figure 1-1 Product Labeling (Front side view)
Label nr. Description
1 LCD panel protection film
2 SC800 logo
3 Warranty seal PDT
Table 1-1 Front labeling

Shin Chuan Computer
User’s Manual
SC800/SC820
1-12
Figure 1-2 Product Labeling (Back side view)
Label nr. Description
4 Laser radiation warning label
5 Serial / Configuration number
6 PenPower label (only use on Simplified Chinese version)
7 CCC label (only use with China)
8 System and regulatory label
9 NCC label (only use on Traditional Chinese version)
10 RoHS Use Life Label for China
11 Windows CE .NET label
Table 1-2 Rear labeling

Shin Chuan Computer
User’s Manual
SC800/SC820
1-13
B. SC820
Figure 1-3 Product Labeling (Front side view)
Label nr. Description
1 LCD panel protection film
2 SC820 logo
3 Warranty seal PDT
Table 1-3 Front labeling

Shin Chuan Computer
User’s Manual
SC800/SC820
1-14
Figure 1-4 Product Labeling (Back side view)
Label nr. Description
4 LED/Laser radiation warning label
5 Serial / Configuration number
6 PenPower label (only use on Simplified Chinese version)
7 CCC label (only use with China)
8 System and regulatory label
9 NCC label (only use on Traditional Chinese version)
10 RoHS Use Life Label for China
11 Windows CE .NET label
Table 1-4 Rear labeling