manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Shinko
  6. •
  7. Controllers
  8. •
  9. Shinko DCL-33A User manual

Shinko DCL-33A User manual

INSTRUCTION MANUAL DIN Rail Mounted Indicating Controller DCL-33A
No. DCL31JE1 2016.06
SHINKO TECHNOS CO., LTD. Head office: 2-5-1, Senbahigashi, Minoo, Osaka, 562-0035, Japan
TEL: +81-72-727-6100 FAX: +81-72-727-7006 URL: http://www.shinko-technos.co.jp/e/ E-mail: overs[email protected]
For detailed usage, refer to the Instruction Manual for the DCL-33A. Please download the full Instruction Manual from Shinko website.
http://shinko-technos.co.jp/e/ Support & Downloads Downloads Manuals
Thank you for purchasing our DCL-33A, DIN Rail Mounted Indicating Controller. This manual contains instructions for the mounting, functions, operations and notes when
operating the DCL-33A. To ensure safe and correct use, thoroughly read and understand this manual before using this instrument. To prevent accidents arising from the
misuse of this instrument, please ensure the operator receives this manual.
Safety Precautions
(Be sure to read these precautions before using our products.)
The safety precautions are classified into 2 categories: “Warning” and “Caution”.
Warning: Procedures which may lead to dangerous conditions and cause death or serious injury, if not
carried out properly.
Caution: Procedures which may lead to dangerous conditions and cause superficial to medium injury or
physical damage or may degrade or damage the product, if not carried out properly.
Caution for Installation
This instrument is intended to be used under the following environmental
conditions (IEC61010-1)]: Overvoltage category , Pollution degree 2
Ensure the mounting location corresponds to the following conditions:
• A minimum of dust, and an absence of corrosive gases
• No flammable, explosive gases
• No mechanical vibrations or shocks
• No exposure to direct sunlight, an ambient temperature of 0 to 50 (32 to
122 ) that does not change rapidly, and no icing.
• An ambient non-condensing humidity of 35 to 85 %RH
• No large capacity electromagnetic switches or cables through which large
current is flowing
• No water, oil or chemicals or where the vapors of these substances can
come into direct contact with the unit
• Take note that the ambient temperature of this unit – not the ambient
temperature of the control panel – must not exceed 50 (122 ) if mounted
through the face of a control panel, otherwise the life of electronic
components (especially electrolytic capacitors) may be shortened.
Warning
• To prevent electric shock or fire, only Shinko or other qualified service personnel may handle the inner
assembly.
• To prevent electric shock, fire or damage to the instrument, parts replacement may only be undertaken by
Shinko or other qualified service personnel.
SAFETY PRECAUTIONS
• To ensure safe and correct use, thoroughly read and understand this manual before using this instrument.
• This instrument is intended to be used for industrial machinery, machine tools and measuring equipment.
Verify correct usage after purpose-of-use consultation with our agency or main office. (Never use this
instrument for medical purposes with which human lives are involved.)
• External protection devices such as protective equipment against excessive temperature rise, etc. must be
installed, as malfunction of this product could result in serious damage to the system or injury to personnel.
Proper periodic maintenance is also required.
• This instrument must be used under the conditions and environment described in this manual. Shinko
Technos Co., Ltd. does not accept liability for any injury, loss of life or damage occurring due to the
instrument being used under conditions not otherwise stated in this manual.
Caution with respect to Export Trade Control Ordinance
To avoid this instrument from being used as a component in, or as being
utilized in the manufacture of weapons of mass destruction (i.e. military
applications, military equipment, etc.), please investigate the end users and
the final use of this instrument. In the case of resale, ensure that this
instrument is not illegally exported.
Specifications
Power supply
voltage
100 to 240 V AC 50/60 Hz, Allowable voltage fluctuation: 85 to 264 V AC
24 V AC/DC 50/60 Hz, Allowable voltage fluctuation: 20 to 28 V AC/DC
EVT output
Alarm output:
(Alarm, Loop break alarm and optional Heater burnout alarm utilize common
output terminals.)
The alarm action point is set by deviation from the SV (excluding Process
alarm), and if the input goes outside the range, alarm is turned ON or OFF
(High/ Low limit range alarm).
When De-energized action is selected in [Alarm action Energized/
De-energized], alarm is activated conversely.
Setting accuracy: Same as basic accuracy
Action: ON/OFF action
Hysteresis: Thermocouple, RTD inputs: 0.1 to 100.0 ( )
DC voltage, current inputs: 1 to 1000 (The placement of the
decimal point follows the selection.)
Output: Open collector, Control capacity: 0.1 A 24 V DC
Alarm type: High limit alarm, Low limit alarm, High/Low limits alarm,
High/Low limits independent alarm, High/Low limit range alarm, High/Low
limit range independent alarm, Process high alarm, Process low alarm,
High limit with standby alarm, Low limit with standby alarm, High/Low
limits with standby alarm, High/Low limits with standby independent
alarm.
Energized/De-energized action are applied to the above alarms, totaling
24 alarm types. No alarm action can also be selected.
Alarm Energized/De-energized: Alarm output Energized/ De-energized can
be selected.
Alarm Energized Alarm De-energized
EVT indicator (Red) Lit Lit
EVT output ON OFF
Alarm HOLD function: Once an alarm is activated, the alarm output is
maintained until the power is turned off.
Loop break alarm output:
(Loop break alarm, Alarm and optional Heater burnout alarm utilize common
output terminals.)
Detects heater burnout, sensor burnout and actuator trouble.
Setting range:
Loop break alarm time: 0 to 200 minutes
Loop break alarm span:
Thermocouple, RTD inputs: 0 to 150 ( ) or 0.0 to 150.0 ( )
DC voltage, current inputs: 0 to 1500 (The placement of the decimal point
follows the selection.)
Output: Open collector, Control capacity: 0.1 A 24 V DC
Basic accuracy
(at ambient
temperature 23 ,
for a single unit
mounting)
Thermocouple input: Within 0.2% of each input span 1 digit, or 2
(4 ), whichever is greater
However, R, S inputs, 0 to 200 (0 to 400 ): Within 6 (12 )
B input, 0 to 300 (0 to 600 ): Accuracy is not guaranteed.
K, J, E, T, N inputs, Less than 0 (32 ):
Within 0.4% of input span 1 digit, or 4 (8 ), whichever is
greater
RTD input: Within 0.1% of each input span 1 digit or 1 (2 ),
whichever is greater
DC voltage input: Within 0.2% of each input span 1 digit
Direct current input: Within 0.2% of each input span 1 digit
Input sampling
period 125 ms
Power
consumption
100 to 240 V AC: Approx. 5 VA max.
24 V AC: Approx. 4 VA max.
24 V DC: Approx. 4 W max.
Ambient
Temperature,
Humidity
0 to 50 ,
35 to 85 %RH (Non-condensing)
Weight Approx. 100 g
Accessories
Instruction manual excerpt: 1 copy
When W option is ordered: Connector harness 3 m 1 length
When
W option
(5A, 10A, 20A) is ordered: CT (CTL-6S) 1 piece
When
W option
(50A) is ordered: CT (CTL-12-S36-10L1U) 1 piece
When EI option is ordered:
Connector harness AOJ 3 m 1 length
When EA option is ordered:
Connector harness AOJ 3 m 1 length
Control output
(OUT1)
Relay contact 1a, Control capacity: 3 A 250 V AC (resistive load)
1 A 250 V AC (inductive load cos =0.4)
Electrical life: 100,000 cycles
Non-contact voltage (for SSR drive): 12 V DC 15%
Max 40 mA (short circuit protected)
Direct current: 4 to 20 mA DC, Load resistance: Max 550
Output accuracy: Within 0.3% of output span
Resolution: 12000
Heating/Cooling
control output
(OUT2)
(DC option)
Output: Open collector, Control capacity: 0.1 A 24 V DC
External Dimensions (Scale: mm)
Name and Functions
N
o.
N
ame
D
escription
①EVT indicator The red LED turns on when Event output (Alarm, Loop break alarm or optional Heater burnout alarm) is ON.
The red LED also turns on when Cooling output is ON if Heating/Cooling control option is ordered.
②OUT indicator
The green LED turns on when OUT (control output) is ON (when Heating output is ON if Heating/Cooling control option is
ordered).
For Direct current output, flashes in 125 ms cycles corresponding to the output MV.
③T/R indicator The yellow LED flashes during Serial communication TX output (transmitting).
④AT indicator The yellow LED flashes while auto-tuning (AT) is performing.
⑤PV Display Indicates the PV (process variable), or setting characters in setting mode with a red LED.
⑥SV Display Indicates the SV (desired value), output MV (manipulated variable) or each set value in each setting mode with a green LED.
⑦UP key Increases the numeric value.
⑧DOWN key Decreases the numeric value.
⑨MODE key Switches the setting mode or registers the set data.
(Registers the set data by pressing the MODE Key.)
⑩SUB-MODE key
Enters Auxiliary function setting mode 2 in combination with the MODE key.
If Control output OFF is selected in [SUB-MODE key function]: Turns all outputs OFF as if the power were turned OFF.
If Auto/Manual control is selected in [SUB-MODE key function]: Switches the Auto/Manual control.
If Alarm HOLD cancel is selected in [SUB-MODE key function]: Cancels Alarm HOLD.
Caution
When setting the specifications and functions of this unit, connect mains power cable to terminals 1 and 2 first, then set them referring to “Key Operation Flowchart”,
before “Mounting to the Control Panel” and “Wiring”.
Do not pull or bend the lead wire on the terminal side when wiring or after wiring, as it could cause malfunction.
Terminal Arrangement
N
ame
D
escription
PWR
(POWER SUPPLY)
100 to 240 V AC or 24 V AC/DC
For 24 V DC, ensure polarity is correct.
O1 Control output (OUT1)
TC Thermocouple
RTD Resistance temperature detector
DC Direct current or DC voltage
For Direct current input, connect a shunt resistor (50 ) between input terminals.
EV Event output
Outputs when Alarm, Loop break alarm or Heater burnout alarm (W option) is ON.
O2 Cooling output (DC option)
RS-485 Serial communication (C5 option)
CT Current transformer input (W option)
EA External setting input (EA option)
EI DI1 input (EI option)
When using ferrules, use the following ferrules made by Phoenix Contact GMBH & CO.
Recommended Ferrules and Crimping Pliers
Terminal
Number
Terminal
Screw
Ferrules with
Insulation Sleeve
Conductor Cross
Sections Tightening Torque Crimping Pliers
1 to 4 M2.6
AI 0.25-8 YE 0.2 to 0.25 mm
2
0.5 to 0.6 N・m
CRIMPFOX ZA 3
CRIMPFOX UD 6
AI 0.34-8 TQ 0.25 to 0.34 mm
2
AI 0.5-8 WH 0.34 to 0.5 mm
2
AI 0.75-8 GY 0.5 to 0.75 mm
2
AI 1.0-8 RD 0.75 to 1.0 mm
2
AI 1.5-8 BK 1.0 to 1.5 mm
2
5 to 9 M2.0
AI 0.25-8 YE 0.2 to 0.25 mm
2
0.22 to 0.25 N・m
AI 0.34-8 TQ 0.25 to 0.34 mm
2
AI 0.5-8 WH 0.34 to 0.5 mm
2
DIN rail
Commu-
nication
C5
(RS-485)
Bottom of the unit
CT
EA
EI
和文は裏面をご覧下さい。
Key Operation Flowchart
●Basic Operation Procedure
Set the input type, Alarm 1 type and SV1 (desired value), following the procedure below.
Setting item numbers (1), (2), (3), (4), (5), (6), (7) and (8) are indicated on the flowchart.
[
S
tep 1
]
Operation before RUN
Turn the load circuit power OFF, and turn the power to the
DCL-33A ON.
[Step 2]
Auxiliary function setting
mode 2
Select an input type and Alarm 1 type, etc. in Auxiliary function
setting mode 2.
(1) Select an input type in [Input type].
(2) Select the Alarm 1 type in [Alarm 1 type].
If any Alarm 1 type except ( ) is selected, (3) to (6)
will be indicated. Set them if necessary.
Note: If Alarm 1 type is changed, the Alarm 1 value will
default to 0 (0.0). Therefore, set the alarm value again.
(3) Select Alarm 1 Energized/De-energized in [Alarm 1
Energized/De-energized].
(4) Select either Alarm 1 Holding or Not holding in [Alarm 1
HOLD function].
(5) Set the Alarm 1 hysteresis in [Alarm 1 hysteresis].
(6) Set the Alarm 1 delay time in [Alarm 1 delay time].
[
S
tep 3
]
Sub setting mode (7) Set the Alarm 1 value in [Alarm 1 value].
[
S
tep 4
]
Main setting mode (8) Set the SV1 (desired value) in [SV1 (desired value)].
[Step 5] RUN Turn the load circuit power ON. Control action starts so as to
keep the control target at the SV1 (desired value).
●Alarm Type
High limit alarm
The alarm action is deviation setting from the SV.
The alarm is activated if the input value reaches the
high limit set value.
Low limit alarm
The alarm action is deviation setting from the SV.
The alarm is activated if the input value goes under
the low limit set value.
High/Low limits alarm
Combines High limit and Low limit alarm actions.
When input value reaches the high limit set value or
goes under the low limit set value, the alarm is
activated.
High/Low limit range
alarm
When input value is between the high limit and low
limit set values, the alarm is activated.
Process alarm
Within the scale range of the controller, alarm action
points can be set at random and if the input reaches
the randomly set action point, the alarm is activated.
High limit alarm with
standby
Low limit alarm with
standby
High/Low limits alarm
with standby
After the power supply to the instrument is turned
on, even if the input enters the alarm action range,
the alarm is not activated. If SV is changed while
the controller is running, the alarm is not activated
even if the input is in the alarm action range. (If the
controller is allowed to keep running, the standby
function will be released once the input exceeds the
alarm action point.)
●Character Indication
AT Perform/Cancel
Cancel
Perform
Set value lock
Unlock
Lock 1
Lock 2
Lock 3
Communication protocol
Shinko protocol
Modbus ASCII mode
Modbus RTU mode
Shinko protocol
(Block read)
Modbus ASCII mode
(Block read)
Modbus RTU mode
(Block read)
Communication speed
2400 bps
4800 bps
9600 bps
19200 bps
38400 bps
Parity
No parity
Even
●About Setting Item
Upper left: PV Display: Indicates setting characters. Lower left: SV Display: Indicates the factory default.
Right side: Indicates the setting item.
: This setting item is optional, and appears only when the option is ordered.
●Key Operation
•+ : Press and hold the key and key (in that order).
•+ (3 sec) : Press and hold the key and key (in that order) together for approx. 3 seconds..
•+ (3 sec) : Press and hold the key and key (in that order) together for approx. 3 seconds.
•+ (3 sec) : Press and hold the key and key (in that order) together for approx. 3 seconds.
•Set or select each item with the or key, and register the value with the key.
•: If the key is pressed, the unit proceeds to the next item, illustrated by an arrow.
•To revert to the PV/SV Display, press the key for approx. 3 seconds in any mode.
Odd
Input Type
K -200 - 1370°C
K -199.9 - 400.0°C
J -200 - 1000°C
R 0 - 1760°C
S 0 - 1760°C
B 0 - 1820°C
E -200 - 800°C
T -199.9 - 400.0°C
N -200 - 1300°C
PL-
Ⅱ
0 - 1390°C
C(W/Re5-26) 0 - 2315°C
Pt100 -199.9 - 850.0°C
JPt100 -199.9 - 500.0°C
Pt100 -200 - 850°C
JPt100 -200 - 500
℃
K -320 - 2500°F
K -199.9 - 750.0°F
J -320 - 1800°F
R 0 - 3200°F
S 0 - 3200°F
B 0 - 3300°F
E -320 - 1500°F
T -199.9 - 750.0°F
N -320 - 2300°F
PL-
Ⅱ
0 - 2500°F
C(W/Re5-26) 0 - 4200°F
Pt100 -199.9 - 999.9°F
JPt100 -199.9 - 900.0°F
Pt100 -300 - 1500°F
JPt100 -300 - 900°F
4 - 20 mA -1999 - 9999
0 - 20 mA -1999 - 9999
0 - 1 V -1999 - 9999
0 - 5 V -1999 - 9999
1 - 5 V -1999 - 9999
0 - 10 V -1999 - 9999
4 - 20 mA -1999 - 9999
0 - 20 mA -1999 - 9999
Decimal point place
No decimal point
1 digit after point
2 digits after point
3 digits after point
OUT2 cooling method
Air cooling
Oil cooling
Water cooling
A1 - A4 type
No alarm action
High limit alarm
Low limit alarm
H/L limits alarm
H/L limit range
Process high alarm
Process low alarm
High limit with standby
Low limit with standby
H/L limits with standby
H/L limits independent
H/L limit range
independent alarm
H/L limits with standby
independent alarm
A1 - A4 Energized/De-energized
Energized
De-energized
A1 - A4 HOLD function
Not holding
Holding
Direct/Reverse action
Reverse action
Direct action
Output status when input errors occur
Output OFF
Output ON
Controller/Converter
Controller
Converter
Event input DI allocation (*)
No event
Set value memory
Control ON/OFF
Direct/Reverse action
Preset output 1
ON/OFF
Preset output 2
ON/OFF
Auto/Manual control
Integral action Holding
Set value memory
Control ON/OFF
Direct/Reverse action
Preset output 1
ON/OFF
Preset output 2
ON/OFF
Auto/Manual control
Integral action Holding
A1 - A4 value 0 Enabled/Disabled
Disabled
Enabled
Remote/Local
Local
Remote
SV Rise/Fall rate start type
SV s t art
PV s t art
Control output OUT1/EVT
OUT1
EVT
HB alarm output Enabled/Disabled
Disabled
Enabled
LB alarm output Enabled/Disabled
Disabled
Enabled
A1 - A4 output Enabled/Disabled
Disabled
Enabled
SUB-MODE key function
Control output OFF
Auto/Manual control
Alarm HOLD cancel
Auto/Manual after power ON
Automatic control
Manual control
Abbreviations:
HB: Heater burnout
LB: Loop break
(*)
001 to 007: Works when contacts are closed (Input ON).
008 to 014: Works when contacts are open (Input OFF).

Other manuals for DCL-33A

7

Other Shinko Controllers manuals

Shinko BCS2R Series User manual

Shinko

Shinko BCS2R Series User manual

Shinko ACD-13A User manual

Shinko

Shinko ACD-13A User manual

Shinko DCL-33A User manual

Shinko

Shinko DCL-33A User manual

Shinko ACS-13A User manual

Shinko

Shinko ACS-13A User manual

Shinko PCD-33A User manual

Shinko

Shinko PCD-33A User manual

Shinko JCL-33A Series User manual

Shinko

Shinko JCL-33A Series User manual

Shinko PCA1 User manual

Shinko

Shinko PCA1 User manual

Shinko JCR-33A User manual

Shinko

Shinko JCR-33A User manual

Shinko PCA1 User manual

Shinko

Shinko PCA1 User manual

Shinko ACD-15A-R/M User manual

Shinko

Shinko ACD-15A-R/M User manual

Shinko ACD-13A Use and care manual

Shinko

Shinko ACD-13A Use and care manual

Shinko DCL-33A Use and care manual

Shinko

Shinko DCL-33A Use and care manual

Shinko PCD-33A User manual

Shinko

Shinko PCD-33A User manual

Shinko DCL-33A User manual

Shinko

Shinko DCL-33A User manual

Shinko JCL-33A Series Use and care manual

Shinko

Shinko JCL-33A Series Use and care manual

Shinko DCL-33A User manual

Shinko

Shinko DCL-33A User manual

Shinko JCR-33A User manual

Shinko

Shinko JCR-33A User manual

Shinko DCL-33A User manual

Shinko

Shinko DCL-33A User manual

Shinko FCR-13A User manual

Shinko

Shinko FCR-13A User manual

Shinko ACS-13A-*A Series User manual

Shinko

Shinko ACS-13A-*A Series User manual

Shinko PC-935 series Use and care manual

Shinko

Shinko PC-935 series Use and care manual

Shinko JCS-33A User manual

Shinko

Shinko JCS-33A User manual

Shinko ACS-13A User manual

Shinko

Shinko ACS-13A User manual

Shinko PCB1 User manual

Shinko

Shinko PCB1 User manual

Popular Controllers manuals by other brands

Beijer Electronics EXTER T60 installation manual

Beijer Electronics

Beijer Electronics EXTER T60 installation manual

Turnstiles KT-2 quick start guide

Turnstiles

Turnstiles KT-2 quick start guide

Pilz PSEN op67-69K Series manual

Pilz

Pilz PSEN op67-69K Series manual

Stag AFR operating instructions

Stag

Stag AFR operating instructions

microHAM micro2R u2R user guide

microHAM

microHAM micro2R u2R user guide

Armacost Lighting 513125 manual

Armacost Lighting

Armacost Lighting 513125 manual

ABB Advant Controller 450 user guide

ABB

ABB Advant Controller 450 user guide

Zmotion ZMC408SCAN manual

Zmotion

Zmotion ZMC408SCAN manual

NEXCOBOT RCB600 Quick reference guide

NEXCOBOT

NEXCOBOT RCB600 Quick reference guide

Sturtevant Richmont TCV operating instructions

Sturtevant Richmont

Sturtevant Richmont TCV operating instructions

Control Resources SmartFan Cirrus-6 Installation & operation manual

Control Resources

Control Resources SmartFan Cirrus-6 Installation & operation manual

IDEC MICROSmart FC6A Series Ladder Programming Manual

IDEC

IDEC MICROSmart FC6A Series Ladder Programming Manual

Emerson Fisher 95L instruction manual

Emerson

Emerson Fisher 95L instruction manual

Hanna Instruments HI 720 instruction manual

Hanna Instruments

Hanna Instruments HI 720 instruction manual

sauter EQJW145 operating manual

sauter

sauter EQJW145 operating manual

involight COMMANDER EASYCONTROL manual

involight

involight COMMANDER EASYCONTROL manual

Deep Sea Electronics Plc 550 manual

Deep Sea Electronics Plc

Deep Sea Electronics Plc 550 manual

iNels IART2-1 instruction manual

iNels

iNels IART2-1 instruction manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.