Shinybow USA ANI-44C5HD User manual

ANI-44C5HD
Super HDMI Matrix 4x4 over HDBaseT
INSTRUCTION MANUAL

USER MANUAL
Table of Contents
1.0 Introduction..........................................................................1
2.0 Specifications.......................................................................2
3.0 Package Contents................................................................2
4.0 Panel Descriptions...............................................................3
5.0 Connection and Operation..................................................5

Super HDMI Matrix 4×4 over HDBaseT
１
Super HDMI Matrix 4x4 over HDBaseT
Dear customer
Thank you for purchasing this product. For optimum performance and safety,
please read these instructions carefully before connecting, operating or adjusting
this product. Please keep this manual for future reference.
1.0 INTRODUCTION
This Super HDMI Matrix offers unprecedented flexibility and convenience by
routing high definition audio/video from any of four HDMI video sources to any of
4 displays over HDMI cable or 4 remote displays over inexpensive, standard
CAT5e/6 cable. With built-in 4 HDBaseT modules, It can extend your HD display
up to 330 feet (100 meters) away from your HDMI or DVI-D source using one
CAT5e/6 cable.Four receivers work with the main sender as a full functional
module. Every source and display is accessible at all times by selecting it with an
IR remote or through RS232 port.
1.1 FEATURES
This product has many features that enable it to perform in a superior manner.
Among those features you will find:
zAllows any HDMI display to view any source at any time
zAllows any source to be displayed on multiple displays at the same time
zEach Output includes one HDMI output and HDBaseT output, but only one
way is available at a time.
zEach HDBaseT output is connected to a Receiver.
zHDBaseT output extends signal up to 100m for 1080p by one CAT5e/6 cable.
zEach Input includes an infrared Emitter, which is used to control the
long-distance source device by Remote Control.
zEach display's inputs can be switched with the IR remote control or through
RS232
zSupports highest video resolution 1080p.
zSupports 225MHz/2.25Gbps per channel (6.75Gbps all channel) bandwidth.
zSupports 12bit per channel (36bit all channel) deep color.
zSupports HDCP
zSupports uncompressed audio such as LPCM.
zSupports compressed audio such as DTS Digital, Dolby Digital（including
DTS-HD and Dolby True HD）.
zSupport 3D all format, including [email protected]/24Hz, [email protected]/60Hz/50Hz,
bandwidth up to 225MHz.
zBuilt-in IR extender function allows IR remote control of Source devices from
remote viewing location by sending IR commands received in the vicinity of
the Display back to the Source devices.

Super HDMI Matrix 4×4 over HDBaseT
２
2.0 SPECIFICATIONS
Signal Inputs/Output
HDMI Connector type A 19 pin female
Input DDC Signal 5 volts p-p (TTL)
Control Port RS-232 Female, Mini-Stereo
Output Signal HDMI output, HDBaseT output
Operating Frequency
Vertical Frequency Range 50/60Hz
Video Amplifier Bandwidth 2.25Gbps/225MHz
Resolutions(HDTV)
Interlaced(50&60Hz) 480i,576i,1080i
Progressive(50&60Hz) 480p,576p,720p,1080p
Mechanical
Size of HDMI Switch Splitter (L-W-H) 441×202×45MM
Weight of HDMI Switch Splitter (Net) 2330g
Warranty
Limited Warranty 1 Year Parts and Labor
Environmental
Operating Temperature 0 ℃to +70℃
Operating Humidity 10% to 85 % RH (no condensation)
Storage Temperature -10℃to +80℃
Storage Humidity 5% to 90 % RH (no condensation)
Power Requirement
Power Supply for Super HDMI Matrix 12V DC@3A
Power consumption (Max) 24W
Power Supply for Receiver 5V DC@2A
Power consumption (Max) 5W
Regulatory Approvals
Converter Unit FCC,CE,UL
Power Supply UL,CE,FCC
Note: Specifications are subject to change without notice.
3.0 Package Contents
Before attempting to use this unit, please check the packaging and make sure the
following items are contained in the shipping carton:
Packaging of Main Unit
1) Main unit
2) Remote Control x1
3) External infrared receiver (IR) x1
4) External infrared emitter (IE) x4
5) 12V@3A DC Power Supply x1

Super HDMI Matrix 4×4 over HDBaseT
３
6) User’s Manual x1
Packaging of Accessories
7) Receivers x4
8) Remote Control for Receivers x4
9) External infrared receiver (IR) x4
10)5V DC @2A Power Supply x4
4.0 PANEL DESCRIPTIONS
Please study the panel drawings below and become familiar with the structure.
Main Unit
①IR Receiver
This receiver will accept command for switching between HDMI input devices
using the included Main unit remote control.
②"Select button" and "Input LED indicator"
There is a set of 4 LEDs for each of the four output ports. Each of the four LED
output sets contain 4 individual LED’s that will indicate which input source is
active for that output. The currently selected input will be indicated by an active
LED.
③Power indicator
This LED will become active once the included 12V DC power supply is
properly connected between the unit and a open wall power receptacle.
④Standby
Pressing this button, the main unit will access standby mode.
⑤DC/12V
Connect the included 12V DC power supply between this port and an open
wall power receptacle.
⑥HDMI and HDBaseT output ports (only one way is available at a time.)
Connect 4 local HDTVs to 4 HDMI output ports.

Super HDMI Matrix 4×4 over HDBaseT
４
Connect 4 receivers to 4 HDBaseT output ports.
⑦IE(Infrared emitter) and HDMI Input ports
Connect 4 Infrared emitters to 4 IE ports.
Connect 4 HDMI source devices to 4 HDMI Input ports.
⑧IR EXT
Connect external IR receiver to this port.
⑨RS232
Connect this port to PC, and over the “super terminal” of PC, you can control
and switch the main unit.
Receiver
①IR Receiver
This receiver will accept command for switching between HDMI input devices
using the included the remote control of the Receiver.
②Power indicator
This LED will become active once the included 5V DC power supply is
properly connected between the unit and a open wall power receptacle.
③Input LED indicator
An active LED will be indicated when that input port is selected.
④“Select” button
Press this button to switch the source device.
⑤Power ON/OFF switch
⑥DC/5V
Connect the included 5V DC power supply between this port and an open
wall power receptacle.
⑦HDBaseT input port
Connect the HDBaseT output port of the main unit to this port over one cat5e/6

Super HDMI Matrix 4×4 over HDBaseT
５
cable.
⑧HDMI output port
Connect this port to HDTV.
⑨IR EXT
Connect this port to the external IR receiver.
⑩RS232
Connect this port to PC, and over the “super terminal” of PC, you can control
and switch the Receiver.
5.0 Connection and Operation
5.1 Connection
1) Connect all source devices to the HDMI inputs on the main unit.
2) Either HDMI or HDBaseT can be selected as signal output for Output
A/B/C/D. When choosing the HDMI as signal output, connect displays and
main unit directly over HDMI cable. When choosing HDBaseT as signal output,
connect receivers and main unit over cat5e/6 cable, and then connect output
of receivers to displays. (Note: HDMI and HDBaseT of each output can not be
connected simultaneously)
3) Connect the 12V@3A power supply to the main unit, and 5V@2A power
supply to each receiver.
Note: 1) Please make sure to cut off the power before insert IR Extender into the
Converter.
2) Please make sure to insert the plug of IR Extender into the Converter
completely.
Attention: Insert / Extract cable gently.
5.2 Operation
1) The automatic connection when supplied with power
The available outputs will automatically connect to the available inputs
according to their sequence number. Meanwhile, the redundant available ports
(input or output) or unavailable ports will not be connected.
For example:
1. If outputs A, B, D are connected to three power-on TVs separately, and the
four inputs are all have its own source devices (work-on mode), then the power-on
main unit will make a connection as follow:
1→A 2→B 3→D
(Output C and input 4 are not connected)
2. If outputs A, Care connected to three power-on TVs separately, and only
two inputs have its source devices (work-on mode), then the power-on Switch
Splitter will make a connection as follow:
1→A 3→C
(Output B, output D, input2 and input4 are not connected)
2) Selecting source devices by buttons

Super HDMI Matrix 4×4 over HDBaseT
６
Four buttons on the main unit are used to select source devices circularly for
inputs A, B, C, and D. Once you press the button, it will select next available
source device.
3) Selecting source devices by IR remote
1. Power button
The power button of the IR remote can control the power of the main unit.
Pressing this button, the power-on unit will be turned off. If you press it
again, the unit will be turned on.
2. Other buttons
Depending on outputs A, B, C, D, the other buttons of the IR remote can
be divided into four groups. Each group has five buttons: ‘off’—turn off its
outputs. 1, 2, 3, 4 are used to select input port accordingly.
4) Selecting source devices by RS232
①. Introduction of RS232 remote operation:
RS232 remote operation is mainly based on the “super terminal” of
Windows operation system. Its parameter should be: ANSI 4800 8-N-1-non
②. Operation
A. Connect the switch splitter to the COM of PC with a RS232 cable.
B. Chose the right COM when you setting “super terminal” and then set the
parameter as follow:
Baud frequency：4800
Data bit: 8
Parity bit: N
Stop bit: 1
Data stream: NON
C. Inputting your instruction. The instruction should be two or three letter, and
finish with “Enter” button.
Please input next instruction in three seconds or the”Overtime instruction”
will appear.
The input instruction should be right, or you will be rejected with the “wrong
instruction”
If the input or output that you chose is not connected to devices or not in
power-on mode, “ineffective instruction” will inform you.
If your instruction is performed, you can see the instruction of “successful
operation”.
③. Instruction input method
A. Selecting source device
Sequence number of output (A/B/C/D) + sequence number of the input
(1/2/3/4) + “Enter”
For example: If you want display B to view source 3, then you can input “B3
“and finish with “Enter”.
B. Turning off an output
C + Sequence number of the output that you want to turn off (A/B/C/D) +
“Enter”

Super HDMI Matrix 4×4 over HDBaseT
７
For example: If you want to turn off output B, then you can input CB, and
finish with “Enter”.
C. Turning off the Switch Splitter:
OFF + “Enter”
D. Turning on the Switch Splitter:
ON + “Enter”
E. Inquiry:
QS + “Enter”
This order enables you know which input and output are available and the
connections of input and output.
RS232 Command List
Command Function description
QS Query connected Source and Sink device
ON Turn on the power of 4x4
OFF Turn off the power of 4x4
AU Source and Sink device is connected automatically
A1 "Sink A" select "Source 1"
A2 "Sink A" select "Source 2"
A3 "Sink A" select "Source 3"
A4 "Sink A" select "Source 4"
B1 "Sink B" select "Source 1"
B2 "Sink B" select "Source 2"
B3 "Sink B" select "Source 3"
B4 "Sink B" select "Source 4"
C1 "Sink C" select "Source 1"
C2 "Sink C" select "Source 2"
C3 "Sink C" select "Source 3"
C4 "Sink C" select "Source 4"
D1 Sink D select "Source 1"
D2 Sink D select "Source 2"
D3 Sink D select "Source 3"
D4 Sink D select "Source 4"
CA Turn off the output of Sink A
CB Turn off the output of Sink B
CC Turn off the output of Sink C

S u per H D M I M at r ix 4 × 4 o v er H D B as eT
CD Turn off the outputof SinkD
5.3 CONECTION DIAGRAM
P/N3030
8
END OF DOCUMENT