Shinybow USA SB-5688CK User manual

INSTRUCTION MANUAL
MODEL : SB-5688CK
8x8 HDMI-HDBaseT Matrix Switcher
8x8 HDMI Over HDBaseT Matrix Switch with Single CATx
HDMI over HDBaseT Matrix Switcher Series
Thank you for purchasing the SB-5688CK HDMI-HDBaseT Matrix Switcher. You will find this unit easy to install
and highly reliable but it is essential that you read this manual thoroughly before attempting to use 8x8 HDMI-
HDBaseT Matrix switcher.
MULTIMEDIA AUDIO AND VISUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF AGENERAL NATUREAND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for sufficient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed,stored in aretrieval system,or anyof itspart translated
into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent
© Copyright 1997. All Rights Reserved.
Version 1.2 JULY 2014
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
CONTENTS
INTRODUCTION ...............................................................1
PACKAGE CONTENTS .................................................. 2
FEATURES ....................................................................... 3
SPECIFICATIONS ............................................................ 4
FRONT PANEL ................................................................. 5
FRONT PANEL - EDID ............................................... 6
FRONTPANEL- ALL-OFF-LOCK-ENTER ...............7
FRONTPANEL-RECALL-MEMORY...........................8
REAR PANEL ................................................................... 9
BACKPANEL- HDMIINPUT/ OUTPUT..................... 10
BACK PANEL - HDBaseT CONTROLS ..................... 11
BACK PANEL - HDBaseT I/O ................................... 12
REMOTE CONTROL ...................................................... 13
EDID FUNCTIONS ......................................................... 17
TYPICAL APPLICATION ............................................... 20
IR EXTENDER ............................................................... 23
ETHERNET SERIAL INTERFACE ................................ 25
RS-232 PROTOCOL .................................................... 26
INTRODUCTION
The SB-5688CK is professional 8x8 matrix routing switch.
Supporting eight (8) HDMI Inputs and (8) HDMI and (8) HDBaseT
(PoH optional via the SB-5688CAP*) Outputs. The SB-5688CK
is based on the HDBaseT standard and supports full HDMI video
resolution with embedded EDID and PoH function (optional via
the SB-5688CAP), Audio, RS-232, Ethernet and Bi-Directional IR,
all over a single CATx cable. With a signal bandwidth of 340Mhz,
so there is no signal degradation. High definition digital signals
can be selected and distributed to any (8) Inputs to (16) Outputs
simultaneously (channel outputs mirrored). The switcher is certified
as being fully CEC and HDCP 2.0 compliant, full HD 4K2K HDMI
V1.4a, 3D formats, data rates up to 6.75 Gbps. Supports UXGA/
WUXGA/DVI 1920x1200 resolution to any HD displays. The SB-
5688CK has 1x HDMI for Input, effectively making this an 8 in x16
out switcher (same signal on both HDMI and HDBaseT outputs).
Using IR remote the switcher’s HDBaseT extender transmitter (Tx)
allows you to connect a source in a remote location. Likewise, the
HDBaseT output and our HDBaseT receiver allows you to connect
a display in a remote location. The EDID management can be
selected between eight (8) different modes. Control is provided via
Front panel push buttons, IR remote, RS-232 or TCP/IP(not a web-
browser). An RS-232 Windows GUI interface is provided for matrix
routing control (Windows only).
* The SB-5688CAP optional PoH feature can be ordered separately.
This is considered a special order item and requires approximately a 10
day lead time.
1

PACKAGE CONTENTS
PACKAGE CONTENTS
Check that you have the following components;
• SB-5688CK Matrix Switcher
• RS-232 V2.0 Protocol Instructions
• Ethernet V2.0 Protocol Instructions
• Master wireless IR Remote Control (SW-HD88CK)
• (8) each; Individual wireless IR Control (SW-HD88CK-IR01~IR08)
• 19 inch Ear mount bracket (Part # 2U-440L)
• SB-101 IR Extender distance ~982 feet (300M) Transmitter set.
• SB-100 IR Extender distance ~982 feet (300M) Receiver set.
• SB-101C IR Extender distance 6.5 feet (2M) Transmitter Cable.
• SB-100C IR Extender distance 6.5 feet (2M) Receiver Cable.
• CD Contents : This manual, Windows GUI, ISP V1.0 Windows driver
• RS-232 Cable 6.5 feet (2M)
• ISO Screws
• Users Guide
• Worldwide Universal Power Supply Input : 100~240 VAC, AC 50/60Hz
-- SB-6335R HDBaseT Receiver sold separately –
2

FEATURES
FEATURES
Based on HDBaseT; bi-directional IR, RS-232, Multi FormatAudio, Ethernet and PoH (Optional via the SB-5688CAP). Full Resolution HD
Video, all HDBaseT signals over single CATx cable.
• (8)x HDMI digital video and digital multi-channel audio player source devices matrix switched to (8)x HDMI outputs and (8)x HDBaseT
Transmitter with optional PoH (via the SB-5688CAP) output to (8)x destinations.
• Application HDBaseT specification with optional PoH (via the SB-5688CAP), IR, RS-232, multi-channel digital audio format and HD
video signals over single CATx (6/6a/7) category cable.
• HDMI digital video w/ embedded HDCP, DVI format and CEC/HDCP 2.0 compliant
• Worldwide control EDID modes for HDMI full 4K2K (24/30 Hz) HD video resolutions.
• Link speeds of up to 6.75 Gbps (link clock rate of 340MbHz). Supports HDMI 4K2K, 1.4a 3D formats.
• Wide range of HD resolutions from PC: XGA to WUXGA 1920x1200 and HDTV/DTV HDMI: resolutions 480i/480p, 576i/576p, 720p,
1080i/p & 4K2K (24/30Hz).
• Compatible with all HDMI source devices, PC monitors, Plasma HD displays, HDTV and audio receivers or audio amplifiers.
• Digital video TMDS formats resolution up to 4K2K with deep color 36-bit.
• Digital Audio Support :
• Dolby TrueHD,
• Dolby Digital,
• Dolby Digital Plug/ex,
• DTS,
• DTS-HD,
• DTS-HD Master,
• DTS-EX
• PCM,
• PCM2,
• LPCM2
• Audio Input Supports: HDMI multi-channel digital Audio
• Audio Output Supports: HDMI multi-channel digital Audio
• Various User Interface Controls:
• Windows based GUI control via RS-232 port
• Front panel push button
• IR wireless remote controller
• Ethernet switch control
• Third party RS-232 controller (via simple ASCII)
• Support world wide (10)x control function keys:
• Full function front panel controls: ARC / AUX/ ALL / OFF / EDID / LOCK / RECALL / MEMORY / ENTER
• Support EDID modes :
• a. Embedded EDID modes : FSS/ H24-3D/ H24-3D-M/ H36-3D/ H36-3D-M/ 4K2K-3D / DVI-D 1920x1200-60Hz/ AUTO
• b. External modes : Learning mode.
• Automatic scanning input & output status via LCM show on front panel.
• Support IR Remote and IR Extender with distances up to ~ 984 feet (300M) Maximum
• Support Universal power adaptor AC90V~AC240V, 50/60Hz.
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be invoked.
3

SPECIFICATIONS
SPECIFICATIONS
• Type of HDMI Switcher: 8x inputs To 8x Outputs HDMI over HDBaseT Matrix Switch with Single CATx
• HDMI Support: HDMI 4K2K, 1080p-@60Hz, H36-bit Deep color, 3D of HDMI V1.4 formats
• HDBaseT Support: Bi-directional IR, RS-232, Multi FormatAudio,Ethernet and optional PoH (viathe SB-5688CAP),over one CATx cable.
• HDCP / CEC Support: HDCP 2.2 Compliant, CEC Compliant
• Video Bandwidth: Double Data Rates: 340 MHz, Total 6.75Gbps bandwidth
• Digital Video Support: HD: 480i/ 480p/ 720p/ 1080i/p and 4K2K up to 36bit deep color
• Inputs: 8x HDMI (HDMI or DVI digital source).
• Outputs:
• Video Outputs
• HDMI: 8x HDMI (to Destination).
• HDBaseT: 8x HDBaseT Transmitter with optional PoH (via the SB-5688CAP) over a CATx cable & RJ-45 connector
• HDBaseT Control Inputs:
• 8x IR in (Send IR signals To 8x Rooms via HDBaseT Transmitter)
• 1x ALL IR in (Send IR Signals To 8x Rooms - Via HDBaseT Transmitter)
• HDBaseT Control Out:
• 8x IR out (Link to Receive IR signals from 8x Rooms via HDBaseT Extender)
• 1x ALL IR out (Link to Receive IR signals from 8x Rooms via HDBaseT Extender)
• 1x All Tx LAN (All Switcher HDBaseT Transmitter Ethernet link to HDBaseT Receiver)
• HDBaseT Control I/O:
• 8x RS-232 I/O (Control 8x Rooms RS-232 via Switcher HDBaseT Extender Tx)
• Switcher Controls:
• 1x Select & Function buttons on front panel (Data status via LCM panel show out)
• 1x IR Remote Controller (switch control)
• 8x IR Room Remote Controller (switch control)
• 1x IR External port (switch control via 3.5mm OD Jack)
• 1x RS-232 series interface (switch control)
• 1x Ethernet series interface (switch control)
• Source Status: Input status LEDs indicates presence of a live signal.
• (25) Function Control Keys: 1.ARC, 2.AUX, 3.ALL, 4. OFF, 5. RECALL, 6. ENTER, 7. MEMORY, 8. LOCK, 9. EDID, 10. Destination
button 1 thru 8, 11. Source button 1 thru 8
• (8) EDID management:
• Select Embedded EDID modes : Mode1: FSS, Mode2: H24-3D, Mode3: H24-3D-M, Mode4: H36-3D, Mode5: H36-3D-M,
Mode6: 4K2K-3D, PCM-2CH, Mode7: DVI-D 1920x1200, Mode8: Auto
• Select LEARNING mode : Learning Destination EDID To Link Source.
• Infrared Frequency: 38 Khz
• IR Extend Distance: ~984 feet / 300 meters maximum.
• HDBaseT Extender Distance: ~328 feet / 100 meters maximum.
• HDMI I/O Connector: HDMI Type A - SMD 19-pin female type
• Temperature: Operating Temperature 32°F - 100°F (0°C - 32°C)
• Dimensions (LxWxH): 19 x 9.85 x 3.46 in (482 x 250 x 88mm)
• Rack Mount: 2RU High 19in Rack Mount #2U-440L (with rack mount)
• Power Supply: AC 100~240 VAC 50/60Hz (Power Consumption:10A Maximum)
• Safety Approvals: CE, FCC, RoHS, REACH.
• Product Weight: 3.75 Kgs / 6.25 lb
As product improvements are continuous, specifications are subject to change without notice.
4

FRONT PANEL
FRONT PANEL
1. POWER ON SWITCH
The power switch turns the unit on and off. The LCM will illuminate blue to indicate the switcher is ON and receiving power. The switcher
will remember the last setting during a power cycle. When power is removed and resorted, the last configuration will be evoked.
2. STATUS DISPLAY
Front panel status display shows current matrix routing configuration. This same display also shows particular configuration settings
depending on your current function. In run mode (as shown above), the display shows each Output (destination) Channel shows which
input (source) is assigned.
3. IR SENSOR
The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
4. INPUT STATUS DISPLAY
Input sources 1 to 8 LED illuminates blue to indicate that a video source is present on that input.
5. SOURCE SELECT BUTTONS
Separate inputs 1 thru 8 select buttons are provided each source selection.
6. EDID MODE SELECT BUTTONS
Used to select EDID mode using buttons Source button #1 or #2.
7. DESTINATION SELECT BUTTONS
Separate outputs 1 thru 8 select buttons are provided for each destination assignment.
Routing can be Source to Destination or one source to multiple destinations.
Example : Press Destination 1,3,5 then press Source 2 will route Input 2 to Output 1,3,5 respectfully.
8. 19 INCH EAR MOUNT PAIR
Converts desktop to 19 inch rack mount. Bracket (part # 2U-440L) INCLUDED. Image shows rack mount bracket attached.
5

FRONT PANEL- EDID
FRONT PANEL
12. FUNCTION KEY - EDID (1)
Used to display change current EDID mode.
- Press EDID to select new EDID mode or select
- Press SOURCE row #1 or #2 Select EDID modes.
- Press ENTER to ready memory location.
- Or press EDID again to cancel operation.
Operation completes.
Note : Operation will abort if no keys are pressed within 5 seconds.
FUNCTION KEY - EDID (2)
Select external LEARNING mode
- Press EDID to select new EDID mode or select
- Press Destination again, press the same Destination #1 thru #8 to learn HDBaseT out port EDID, The EDID for HDBaseT (CATx)
has been learned.
- Press ENTER to ready memory location.
- Or press EDID again to cancel operation.
Operation completes.
Note : Operation will abort if no keys are pressed within 5 seconds.
6

FRONT PANEL - ALL - OFF - LOCK - ENTER
FRONT PANEL
13. FUNCTION KEY - ALL
Disables (mute) video on all destinations OR assign the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show ”0” to indicate none of the destinations are assigned a video source.
Option 2
- Press ALL followed by Source 1 thru 8. The display will show the Source selected.
- Press ENTER The pre-set source selection will be assigned all destinations.
14. FUNCTION KEY - OFF
Disables (mute) video on the selected destinations.
- Press OFF button followed by any Destination channel.
- Press 1 thru 8 output destination. The display will show “ 0 “ for the selected channel, indicating no video selected.
15. FUNCTION KEY - LOCK
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
16. FUNCTION KEY - ENTER
Press ENTER to confirm entries.
7

FRONT PANEL - RECALL - MEMORY
FRONT PANEL
17. FUNCTION KEY - RECALL
The system will show previously stored presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or
Destination keys 1 thru 8 as the memory preset location.
- Press RECALL button.
- Press 1 thru 8 on either Source or Destination row.
- Press ENTER The pre-set configuration will execute.
Operation completes.
Note: Operation will abort if no keys are pressed within 5 seconds.
- Or press RECALL again to cancel operation.
18. FUNCTION KEY - MEMORY
The system will show store presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or Destination keys
1 thru 8 as the memory preset location.
- Configure desired matrices.
- Press MEMORY button.
- Press 1 thru 8 on either Source or Destination row.
- Press ENTER to ready memory location.
- Or press MEMORY again to cancel operation.
Operation completes.
Note : Operation will abort if no keys are pressed within 5 seconds.
- Or press MEMORY again to cancel operation.
8

BACK PANEL - SWITCH CONTROLS
BACK PANEL
9
1. DC POWER INLET:
The Switcher is fitted with a AC power plug input connector.
Ensure that the used is of an approved type and is of sufficient
current carrying connector capacity with the correct voltage and
connector polarity. 100~240Volt AC, 50/60Hz power supply.
2. IR EXTENDER CONTROL:
Support one of IR Extender. Extend distance maximum 300
Meters / ~984 feet. When you plug the External IR extender into
the switcher, the front panel IR receiver remain active.
3. RS-232 CONNECTION:
RS-232 control port to allow for interfacing to a PC. Such as a
computer or touch panel control, to the switcher via this DB-9pin
Female connector for serial RS-232 control.
4. ETHERNET CONNECTION:
ETHERNET control port to allow for TCP/IP interfacing to a PC.
Suchasa computeror touch panelcontrol (notaweb-browser), to
the switcher via this RJ-45 Female connector to control switcher.
Power Socket :
Connector Type : IEC 60320 C13
IR Extender Jack: Female Jack - inner OD Ø 3.5mm
Remote Port: D-SUB-9pin Female connector
Remote Port : Control the switcher RJ-45 Female
connector
Ethernet Port:
Note: the Ethernet port and RS-232 port cannot
be used simultaneously. Any connection to the
Ethernet port will disable serial commands send
to the RS-232 port.

BACK PANEL - HDMI INPUT / OUTPUT
BACK PANEL
10
5. INPUTS- 1,2,3,4,5,6,7, & 8 HDMI:
Connect a HDMI signal source link of HDMI source direct HDMI
digital video/audio to this Female HDMI connector. This HDMI
port support HDMI and DVI digital video sources. If you remove
the HDMI screw post, use the provides ISO screw to keep the
internal HDMI jack secure. Removing the HDMI Screws without
installing the ISO screws will void your warranty.
7. OUTPUTS- 1,2,3,4,5,6,7 & 8 HDMI:
Connect an HDMI signal source to this Output. This HDMI port
supports HDMI with embedded audio and DVI with AUX audio.
If you remove the HDMI screw post, you must use the provided
ISO screws to keep the internal HDMI jack secure. Removing
the HDMI Screws without installing the ISO screws will void your
warranty.
HDMI Connector: HDMI Type A SMD 19pin Female
socket connector.
Note: With the proper adapters, the switcher
can be used with DVI digital video signals HDCP
compliant. The DVI support Audio input.
HDMI Connector: HDMI Type A SMD 19pin Female
socket connector
Note: With the proper adapters, the switcher
can be used with DVI digital video signals HDCP
compliant. The DVI Audio supported.

BACK PANEL - HDBaseT CONTROLS
BACK PANEL
11
9. HDBaseT RS-232 - 1,2,3,4,5,6,7 & 8 CONNECTION:
(8)x RS-232 control port to allow for interfacing to a PC. Controls
I/O via Switcher HDBaseT Transmitter (8) Rooms each via this
Terminal Block-3pin Female socket for serial RS-232 control.
10. HDBaseT LAN CONNECTION:
All Tx LAN : Provides Ethernet (LAN) connection from the
switcher to All HDBaseT Transmitter (ie. SB-6320T).
11. HDBaseT IR INPUT - 1,2,3,4,5,6,7 & 8
REMOTE IR SIGNAL TO ROOM:
Send (8)x IR signals to (8) rooms via Switcher HDBaseT
Transmitter. When you plug the Switcher HDBaseT IR Transmitter
intotheexternal port,the roomIRHDBaseTreceiver remain active.
12. HDBaseT IR OUTPUT - 1,2,3,4,5,6,7 & 8
REMOTE IR SIGNAL FROM ROOM:
Receive (8)x IR signals from (8) rooms each via HDBaseT
Transmitter. When you plug the Switcher HDBaseT IR Transmitter
intotheexternal port,the roomIRHDBaseTreceiver remain active.
13. HDBaseT ALL IN : 1,2,3,4,5,6,7 & 8
REMOTE IR SIGNAL TO ROOM:
Send IR signal to room via Switcher HDBaseTTransmitter. When
you plug the Switcher HDBaseT IR Transmitter into the external
port, the room IR HDBaseT receiver remain active.
14. HDBaseT ALL OUT : - 1,2,3,4,5,6,7 & 8
REMOTE IR SIGNAL FROM ROOM:
Receive IR signal from room via Switcher HDBaseT Transmitter.
When you plug the Switcher HDBaseT IR Transmitter into the
external port, the room IR HDBaseT receiver remain active.
Remote Port : Terminal Block-3pin Female socket
ALL HDBaseT Tx LAN Port Connector: HDBaseT
Phone-Jack 8P8C, RJ-45 Female socket.
LAN Controls: Note: from switcher to HDBaseT
Transmitter.
IR Extender Jack: Female Jack - inner OD Ø 3.5 mm
IR Extender Jack: Female Jack - inner OD Ø 3.5 mm
IR Extender Jack: Female Jack - inner OD Ø 3.5 mm
IR Extender Jack: Female Jack - inner OD Ø 3.5 mm

BACK PANEL - HDBaseT I/O
BACK PANEL
Category cable lengths via Switcher and HDBaseT Receiver.
Cable Type Pixel clock rate CAT5e CAT6 CAT6
Resolution (MHz) 70M 100M 100M
1024x768@60Hz 65.00 MHZ Yes Yes Yes
1280x720p@60Hz 73.84 MHZ Yes Yes Yes
1920x1080i@60Hz 74.25 MHZ NA NA NA
1280x1024@60Hz 108.00 MHZ Yes Yes Yes
1920x1080p@60Hz 148.50 MHZ Yes Yes Yes
1920x1200@60Hz 152.90 MHz Yes Yes Yes
1600x1200@60Hz 162.00 MHZ Yes Yes Yes
BD player : 1080p 174.00 MHz Yes NA Yes
12
15. OUTPUT - 1,2,3,4,5,6,7 & 8 HDBaseT (Transmitter):
To send (8) HDMI and control signals via Switcher (8)x HDBaseT
Transmitters to link (8)x external HDBaseT Receiver.
Switcher used (8)x HDBaseT Transmitter Output #1 ~ Output #8
with optional PoH (via the SB-5688CAP) RJ-45 via CATx(6/6a/7)
category cable. Controls signals RS-232, Ethernet, IR input, IR
output and optional PoH (via the SB-5688CAP) between Switcher
and Receiver.
HDBaseT Transmitter Connector: 8x RJ-45 Jack
8P8C Female socket.
Link LED :
solid = valid link
Flash = attempting to link
Off = no link established

13
REMOTE CONTROL
Before making any connections to the switcher, observe the following:
• Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%).
• Ensure that the power switch is OFF.
• Ensure that all system grounds (earth) are connected to a common point.
• Avoid powering equipment within a system from multiple power sources that may be separated by large distances.
• Connect all audio video sources and destination equipment.
• Power up all source and destination audio-visual sources.
• For each destination output, select the appropriate input source by using the front panel input 1~8 select buttons. The supplied IR remote
control or through the RS-232 serial communications port.
• Upon power up the switcher will return to its last used setting before Powered down.
REMOTE CONTROL
IR REMOTE CONTROL KEY :
IR REMOTE : SW-5688
1. & 2. SWITCH POWER ON or OFF:
Controller with a separate power ON and OFF
3. DESTINATION : 1 thru 8 OUTPUT SELECTION:
Press the destination button to select the output display channel.
4. SOURCE : 1 thru 8 INPUT SOURCE SELECTION:
Press input 1~8 sources with selection button.
5. FUNCTION KEY:
ALL - function selection button
OFF - function selection button
EDID - function selection button
RECALL - function selection button
MEMORY - function selection button
ENTER - function selection button
LOCK - function selection button

14
REMOTE PROTOCOL COMMANDS
IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD)
HOW TO SETUP IR CODES : CUSTOM CODE : 09F6
POWER ON : 09F6 A15E
POWER OFF : 09F6 A25D
ALL : 09F6 B04F LOCK : 09F6 B54A
OFF : 09F6 B14E EDID : 09F6 B748
RECALL : 09F6 B24D ENTER : 09F6 B34C
MEMORY : 09F6 B44B
PRESS DESTINATION - # then PRESS SOURCE - #
DESTINATION #1 : 09F6 10EF SOURCE #1 : 09F6 01FE
DESTINATION #2 : 09F6 20DF SOURCE #2 : 09F6 02FD
DESTINATION #3 : 09F6 30CF SOURCE #3 : 09F6 03FC
DESTINATION #4 : 09F6 40BF SOURCE #4 : 09F6 04FB
DESTINATION #5 : 09F6 50AF SOURCE #5 : 09F6 05FA
DESTINATION #6 : 09F6 609F SOURCE #6 : 09F6 06F9
DESTINATION #7 : 09F6 708F SOURCE #7 : 09F6 07F8
DESTINATION #8 : 09F6 807F SOURCE #8 : 09F6 08F7
For example;
Select Destination # 1 to show Source #1~8,
The IR Data Code list :
Destination # 1 , Source #1 09F6 10EF 09F6 01FE 01FE
Destination # 1 , Source #2 09F6 10EF 09F6 01FE 02FD
Destination # 1 , Source #3 09F6 10EF 09F6 01FE 03FC
Destination # 1 , Source #4 09F6 10EF 09F6 01FE 04FB
Destination # 1 , Source #5 09F6 10EF 09F6 01FE 05FA
Destination # 1 , Source #6 09F6 10EF 09F6 01FE 06F9
Destination # 1 , Source #7 09F6 10EF 09F6 01FE 07F8
Destination # 1 , Source #8 09F6 10EF 09F6 01FE 08F7

REMOTE CONTROL
ROOM REMOTE CONTROL #1 ~ #8 CUSTOM CODE AND DATA CODES
IR CUSTOM AND DATA CODES (NEC Standard)
PRESS Number To Select SOURCE
CUSTOM CODE : 09F6
IR-01 DATA CODE: IR-02 DATA CODE:
SOURCE #1 : 09F6 11EE SOURCE #1 : 09F6 21DE
SOURCE #2 : 09F6 12ED SOURCE #2 : 09F6 22DD
SOURCE #3 : 09F6 13EC SOURCE #3 : 09F6 23DC
SOURCE #4 : 09F6 14EB SOURCE #4 : 09F6 24DB
SOURCE #5 : 09F6 15EA SOURCE #5 : 09F6 25DA
SOURCE #6 : 09F6 16E9 SOURCE #6 : 09F6 26D9
SOURCE #7 : 09F6 17E8 SOURCE #7 : 09F6 27D8
SOURCE #8 : 09F6 18E7 SOURCE #8 : 09F6 28D7
IR-03 DATA CODE: IR-04 DATA CODE:
SOURCE #1 : 09F6 31CE SOURCE #1 : 09F6 09F6
SOURCE #2 : 09F6 32CD SOURCE #2 : 09F6 42BD
SOURCE #3 : 09F6 33CC SOURCE #3 : 09F6 43BC
SOURCE #4 : 09F6 34CB SOURCE #4 : 09F6 44BB
SOURCE #5 : 09F6 35CA SOURCE #5 : 09F6 45BA
SOURCE #6 : 09F6 36C9 SOURCE #6 : 09F6 46B9
SOURCE #7 : 09F6 37C8 SOURCE #7 : 09F6 47B8
SOURCE #8 : 09F6 38C7 SOURCE #8 : 09F6 48B7
15

REMOTE CONTROL
ROOM REMOTE CONTROL #1 ~ #8 CUSTOM CODE AND DATA CODES
IR CUSTOM AND DATA CODES (NEC Standard)
PRESS Number To Select SOURCE
CUSTOM CODE : 09F6
IR-05 DATA CODE: IR-06 DATA CODE:
SOURCE #1 : 09F6 51AE SOURCE #1 : 09F6 619E
SOURCE #2 : 09F6 52AD SOURCE #2 : 09F6 629D
SOURCE #3 : 09F6 53AC SOURCE #3 : 09F6 639C
SOURCE #4 : 09F6 54AB SOURCE #4 : 09F6 649B
SOURCE #5 : 09F6 55AA SOURCE #5 : 09F6 659A
SOURCE #6 : 09F6 56A9 SOURCE #6 : 09F6 6699
SOURCE #7 : 09F6 57A8 SOURCE #7 : 09F6 6798
SOURCE #8 : 09F6 58A7 SOURCE #8 : 09F6 6897
IR-07 DATA CODE: IR-08 DATA CODE:
SOURCE #1 : 09F6 718E SOURCE #1 : 09F6 817E
SOURCE #2 : 09F6 728D SOURCE #2 : 09F6 827D
SOURCE #3 : 09F6 738C SOURCE #3 : 09F6 837C
SOURCE #4 : 09F6 748B SOURCE #4 : 09F6 847B
SOURCE #5 : 09F6 758A SOURCE #5 : 09F6 857A
SOURCE #6 : 09F6 7689 SOURCE #6 : 09F6 8679
SOURCE #7 : 09F6 7788 SOURCE #7 : 09F6 8778
SOURCE #8 : 09F6 7887 SOURCE #8 : 09F6 8877
16

EDID FUNCTION
EDID FUNCTION FOR HDMI MATRIX SWITCHER
EDID Setup To Change the EDID Setup
Step 1. Press the EDID button The display will show the currently selected EDID mode
Step 2. Press SOURCE #1 or #2 button row The button will flash blue and the display will show the current Embedded EDID Status.
Step 3. Press the ENTER button To set EDID mode. The switcher will return to operation mode.
Operation will abort if no keys are pressed within 5 seconds.
RESET EDID Return To Factory default
How to RESET EDID mode
Press EDID > RECALL > ENTER
RESET To the FACTORY DEFAULT (1080p-2CH).
Press EDID button : The LCM will show the current EDID status.
Press RECALL button : The LCM will show the RESET EDID.
Press ENTER to confirm entries.
The EDID will return to FSS mode and resolution 1080p-2CH.
Embedded EDID Modes Total 8 EDID Modes
Embedded EDID setup
Press EDID > SOURCE > ENTER
SOURCE #1
or
SOURCE #2
Select Embedded EDID :
Mode 1 : FSS
Mode 2 : H24-3D
Mode 3 : H24-3D-M
Mode 4 : H36-3D
To select Embedded EDID mode or LEARNING mode.
Press EDID button: The LCM will show the current EDID status.
Repeatedly depressing the Source 1 button will cycle up thru the options.
Repeatedly depressing the Source 2 button will cycle down thru the options.
EDID function for HDMI Matrix Switcher
Mode 1. FSS (Fast Speed Start) Fast Speed Start mode shortens the startup time of the switcher. Selecting this mode
does not force the EDID setup to be cancelled. Users may first select one EDID mode
from mode 2 to 3, and then select mode 1 for fast speed start.
Mode 2. H24-3D (1080p-24 bits) Audio Support: PCM 2CH
Mode 3. H24-3D-M (1080p-24 bits) Audio Support: MAT(MLP) 7.1CH, PCM-2CH, One Bit Audio 2CH, AC-3 5.1CH, DTS
5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
Mode 4. H36-3D-M (1080p-36 bits) Audio Support: PCM 2CH
17
Mode 5 : H36-3D-M
Mode 6 : 4K2K-3D, PCM-2CH
Mode 7 : DVI-D 1920x1200-60Hz
Mode 8 : AUTO

EDID FUNCTION
Mode 5 . H36-3D-M (1080p-36 bits) Audio Support : MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3
5.1CH, DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
Mode 6 . 4K2K (24/30Hz) HDMI Support : 4K2K-3D, PCM 2CH (3860x2160-24/30Hz)
Audio Support: PCM 2CH
Mode 7 . 1920x1200-60Hz (DVI-D) DVI Support : DVI-D 1920 x 1200 60Hz
Mode 8 . AUTO <Default> All Outputs will be set to the highest common resolution of all connected
display devices.
LEARNING EDID Learning EDID from Destination to Source
Learning EDID Setup
Press
EDID > DESTINATION > SOURCE > ENTER
Press EDID > DESTINATION Button: The LCM will be show LEARNING.
Switcher will LEARN destination HDMI EDID and pass the selected source.
Learning EDID setup for HDMI: Key Press Sequence:
EDID > DESTINATION # > SOURCE # > ENTER
The EDID for HDMI has been learned
Press
EDID > DESTINATION > DESTINATION >
SOURCE > ENTER
Switcher will LEARN destination HDBaseT CATx EDID and pass the
selected source.
Learning EDID setup for HDBaseT CATx: Key Press Sequence:
EDID > DESTINATION # > DESTINATION # > SOURCE # > ENTER
Again, Press the same DESTINATION # to learn HDBaseT CATx EDID
The EDID for HDBaseT CATx has been learned
NOTE : The already learned EDID cannot be modified. You can only rebuild a new Learning EDID.
For example: When the Source has “Learned” the EDID data from a destination, It will save that EDID information into EPROM and the
EDID data cannot change. Please select new learning destination to sources or change to one of the embedded EDID modes when you
want to remove the learning EDID memory from EPROM.
18