Shoprider TE-9 User manual

MOBILITY SCOOTER USER’S GUIDE
SHOPRIDER NEW ZEALAND
TE-888iXTE-9
Mid size Shoprider scooters with suspension

Shoprider Scooters User Guide
CONTENTS
page page
1 Introduction...............................................1
2 Features......................................................1
3 Safety Precautions.................................... 3
4 Adjustments.............................................. 4
4.1 Seat Slide Adjustment........................... 4
4.2 Seat Swivel Adjustment......................... 4
4.3 Seat Height Adjustment........................ 4
4.4 Seat Tension Adjustment....................... 4
4.5 Captains Seat Back Angle Adjustment... 4
4.6 Armrest Width Adjustment....................4
4.7 Armrest Angle Adjustment.................... 5
4.8 Armrest Height Adjustment...................5
4.9 Tiller Angle Adjustment....................... 5
5 Scooter Operation.....................................5
5.1 Controls................................................ 5
5.1.1 Speed Adjustment Dial................... 5
5.1.2 Horn...............................................5
5.1.3 Thumb Lever Control (Wig Wag).....5
5.1.4 LED Battery Indicator.......................6
5.1.5 Key Switch......................................6
5.1.6 Charging Socket.............................6
5.1.7 Lights............................................. 6
5.1.8 Hazard Lights..................................6
5.1.9 Indicators........................................6
5.1.10 High/Low Speed Switch................ 6
5.1.11 Free Wheeling Device................... 6
5.1.12 Anti Tip Wheels............................ 6
5.2 Mounting..............................................7
5.3 Basic Driving..........................................7
5.3.1 Steering..........................................7
5.3.2 Reversing........................................7
5.4 Dismounting......................................... 7
6 General Advice.......................................... 7
6.1 Control through Obstacles.....................7
6.1.1 Control through Doors................... 7
6.1.2 Control on Ramps...........................8
6.1.3 Control over Grass, Gravel and Hills..8
6.2 Parking in Public....................................8
7 Maintenance..............................................8
7.1 Wheels and Tyres...................................8
7.1.1 Changing Wheels and Tyres............8
7.1.2 Tyre Pressure...................................8
7.2 Lubrication............................................ 9
8 Batteries and Battery Charging................9
8.1 Batteries................................................9
8.2 Battery Charging................................... 9
9 Troubleshooting..................................... 10
9.1 Circuit Breaker and Fuse...................... 10
9.2 If the Scooter does not run..................10
10 Warranty Information...........................10

Shoprider Scooters User Guide 1
13
3
6
2
4
7
1
8
12
14
11
10
9
1 Adjustable back angle Captains chair
with adjustable height head rest
2 Flip back, adjustable width, height and
angle armrests
3 Captains chair rotate lever
4 Side reflectors
5 Tiller control head / steering column
6 Tiller steering column angle adjustment
7 Captains chair fore / aft slide lever
8 Foot rest
9 Rear vision mirrors
10 Battery charging plug (right side)
11 Detachable basket
12 Headlight
13 Front bumper
14 Pneumatic tyres on alloy wheels
1. INTRODUCTION
Congratulations on your purchase of a Shoprider Scooter. Your scooter is the ultimate
combination of style and comfort and incorporates Shopriders latest innovative designs.
Your scooter has been designed to be easily manoeuvred within the smallest spaces both
in and outdoors. Direct drive rear wheels and electromechanical disk brakes provide a safe
comfortable ride. Shoprider scooters are designed for persons with limited mobility.
This manual contains important information regarding the safe use of your scooter. Please,
read it carefully before using your scooter and make sure you understand the instructions.
2. FEATURES
5
TE-9
Mid size scooter with 5 stage suspension and adjustable gas tiller

2Shoprider Scooters User Guide
15
3
6
8
2
5
4
9
1
14
16
13
10
11
12
1 Adjustable back angle Captains chair
with adjustable height head rest
2 Flip back, adjustable width, height and
angle armrests
3 Captains chair rotate lever
4 Rear reflectors
5 Side reflectors
6 Foot rest
7 Tiller control head / steering column
8 Tiller steering column angle adjustment
9 Captains chair fore / aft slide lever
10 Adjustable rear vision mirror
11 Turn indicators
12 Battery charging plug (left side)
13 Detachable basket
14 Bright LED head light
15 Colour keyed front bumper
16 Mag wheels with solid tyres
7
TE-888iX
Modern mid size scooter with suspension and new tiller design

Shoprider Scooters User Guide 3
3. SAFETY PRECAUTIONS
• Donotdrinkalcoholanddrive
• Donotdrink/eatoruseamobilephonewhileriding
• Donotcarrypassengers
• Donotexceedanyinclineover9°
• Donotturnonsteepinclines
• Donotproceedonanyinclinethathasoil,iceorotherslipperysubstances
• Proceedcarefullywhenonanyincline,alwaysleanforward
• Donotoperatescooterwithoutanti-tipwheelsattached-doingsocouldcauseinjury
• Donotturnsuddenlyatfullspeed
• Donotmountordismountthescooterunlessthebrakeisengagedandthekeyisoff
• Donotswitchoffthescooterwhilethescooterismoving
• Donotridethescooterwhereyoucannotsafelywalk(e.g.softdirt/sand,deepgrass,
loose gravel)
• Alwaysproceedcarefullywhileridingonunevensurfaces
• Donotridethescooteronroads,streetsormotorways
• Remembertoobserveallrulesandregulationsofotherpedestrians
• Donotattempttoclimboverkerbsgreaterthan2inches(5cm).Forkerbsunder2inches,
alwaysapproachslowlyandat90°tothekerb.
• Donotreversethescooterunlessthespeeddialissetlow
• Alwaysstopfullybeforechangingdirection(forwardorreverse)
• Alwayskeepyourfeetontheplatformwhenriding
• DonotusepartsoraccessoriesthatarenotauthorisedbyShopriderNZ
• Donotconnectanymedicaldevicetothescooterbattery-doingsocouldcauseinjury
• Donotexceedthesuggesteduserweightlimit-doingsocouldcauseinjuryand
invalidate the warranty
• Makesurethetillerandseatareproperlyadjusted-failuretodosocouldcause
personal injury
• Donotsitonyourscooterwhilethescooterisbeingtransportedinavehicle-doingso
could cause injury
• Donotusethescooterasacommercialdeliveryvehicle,e.g.fordeliveryofleaet,
newspapers etc
• Donotusethescooterintherain,intheshower,orinanywetenvironment-direct
exposuretowetcancauserustandfailureoftheelectronics
ShoprideralsoknownasShopriderNZLtdarenotresponsibleforanydamageorinjury
caused due to improper or unsafe use of their scooters.
EMI Warning
Shoprider scooters may be susceptible to electromagnetic interference (EMI), which is a kind
of interfering electromagnetic energy (EM) emitted from sources such as radio stations, TV
stations,amateurradio(HAM)transmitters,two-wayradio,andcellularphones.Donot
operatehandheldtransceivers(transmitters-receivers),suchascitizensband(CB)radios,or
turn on personal communication devices, such as cellular phones, while the scooter is turned
on. Be aware of nearby transmitters, such as radio or TV stations and try to avoid getting
close to them. Adding accessories or components or modifying the scooter may make it more
susceptible to EMI.

4Shoprider Scooters User Guide
4. ADJUSTMENTS
The Shoprider Scooter allows various adjustments to be made to suit your requirements:
4.1 - SEAT SLIDE ADJUSTMENT
A lever located under the front of the seat, allows you to adjust your seat forward and back.
Simply lift the lever and move in the desired direction. As soon as you release the lever, the
seat will lock in the new position you have selected.
4.2 - SEAT SWIVEL ADJUSTMENT
Lift the red lever located underneath the right side of the seat and rotate the seat around 90º.
The seat will lock into position once the lever has been released.
4.3 - SEAT HEIGHT ADJUSTMENT
Lift the red “Seat Swivel Adjustment” lever and lift the seat clear of the scooter. Loosen
the“SeatTensionAdjustment”knob(TE9)orhexbolt(TE888iX)andremovethesteel
locking pin, the seat post has several different position holes. Retighten the “Seat Tension
Adjustment” knob/bolt and replace the seat once you have chosen your new position hole.
4.4 - SEAT TENSION ADJUSTMENT
Theseattensionknob(TE9)orhexbolt(TE888iX)tightenstheseatposttothescooterframe.
4.5 - CAPTAIN SEAT BACK ANGLE ADJUSTMENT
At the bottom of the seat back on the right side there is a lever to recline the back. Simply lift
the lever and adjust the seat back angle to the position required. The back is also provided
withanadjustableheadrestextension.Thebackfoldsdownontotheseatallowingtheunit
to be stored in a limited space.
4.6 - ARMREST WIDTH ADJUSTMENT
On each side underneath you will find a knob. By loosening this knob you are able to adjust
the armrests to whatever width you desire. The armrests can be removed for transporting the
scooter but must be fitted when using the scooter.
4.1
4.8
4.6
4. Adjustments
4.9
4.5
4.7
4.2
4.4
4.3

Shoprider Scooters User Guide 5
4.7 - ARMREST ANGLE ADJUSTMENT
Pull up on the end of the armrests and they will flip back up allowing easy transfer in and
outoftheseat.Underthearmrests,onsomemodels,thereisaboltandlock-nutthatcanbe
adjusted up/down to change the angle of the armrests.
4.8 - ARMREST HEIGHT ADJUSTMENT (TE 888iX only)
At the rear of the armrest on the down supporting tube there is a knob that allows you to
reposition the tube and armrest. Once the knob has been fully removed you can then adjust
the armrest to a new height using the positional holes. Replace and retighten the adjustment
knob and repeat for the other side.
4.9 - TILLER ANGLE ADJUSTMENT
On the right side of the tiller near the top, a black release lever can be located. By pushing
the lever down you can adjust the tiller angle to a different position. Releasing the lever locks
the tiller in that position.
5. SCOOTER OPERATION
5.1 - CONTROLS
5.1.1 - Speed Adjustment Dial
This allows you to select your desired top speed. The dial can be set anywhere between the
0 (slowest) and 10 (fastest) speed setting.
5.1.2 - Horn Button
Press the round yellow horn button to sound the horn.
5.1.3 - Thumb Lever Control (Wig Wag)
This controls your speed and forward and reverse motion. The right thumb lever moves
the scooter forward and controls the speed. The left thumb lever moves the scooter in
reverse and also controls the speed. When the lever is released you will stop gently and the
electromagnetic brake will be applied.
5.1 Controls
5.1.10 5.1.1
5.1.3 5.1.35.1.2 5.1.25.1.8
5.1.75.1.10
5.1.9
5.1.95.1.4 5.1.45.1.1 5.1.5
5.1.55.1.7
5.1.9 5.1.8

6Shoprider Scooters User Guide
5.1.4 - LED Battery Indicator
These indicate the amount of charge you have in the batteries. The number of bars lit,
shows the amount of charge left in your batteries. The amount of charge will only show at
its true level when the scooter is in drive.
WARNING! - Do not allow the bars to go out completely as the complete discharge of the
batteries could cause them irreversible damage.
5.1.5 - Key Switch
Insert the key and turn clockwise (the LED bars will illuminate). There is a 3 second delay
while the controller checks its circuits before the thumb lever control can be operated. Turn
keyanti-clockwisetoturnscooteroff.
5.1.6 - Charging Socket
Locatednearthetopofthetillerontheleftside(TE888iX)orrightside(TE9)youwillnd
the charging socket. For recharging the batteries see 8.2 for battery charging.
5.1.7- Lights
Press the round blue button to turn the light(s) on and press again to turn off.
5.1.8 - Hazard Lights
Press the triangle shaped red button for the front and rear hazard lights to operate.
5.1.9 - Indicators
On the (TE 9) a black switch works the indicators left or right when moved sideways.
The(TE888iX)hastwoyellowtriangularbuttonsthatindicateleftorrightwhenpushed.
5.1.10 - High/Low Speed
This black switch offers a low speed or high speed range with a flick of the switch.
5.1.11 - Free Wheeling Device
Locatedunderthebodyattherearofthescooterontheleft(TE888iX)orright(TE9)side
is either a red or yellow handle lever. To freewheel the scooter simply push down the lever.
To engage the motor again, just pull the lever up. In freewheel mode the speed control
(wig wag) will not move the scooter and the scooter will not operate.
WARNING! - Always re-engage the free wheeling device after use. Failure to do so may
result in injury. Do not sit on the scooter while in freewheel mode.
5.1.12 - Anti-Tip Wheels
These wheels are located on the rear frame of the scooter.
5.1 Controls
5.1.12
5.1.11
5.1.6

Shoprider Scooters User Guide 7
5.2 - MOUNTING
For your first sessions, be sure that you and the scooter are on a level surface. Put the key in
its slot, but leave it turned off. Grip the hand lever located at the right hand side of the seat
andpulltheleverup.Thiswillreleasetheseatfromitssetlocation.Theseathasfourxing
pointsandwhenrotatingtheseatafterreleasefromoneofitslocationsthespring-loaded
catch will lock into your required position. Seat yourself and swing the seat to face the
handlebars. Make sure you are straight.
5.3 - BASIC DRIVING
l Make sure you are properly seated on the scooter
2 Turn the Speed Adjustment Dial (fig 5.1.1) to slow.
3 Turnkey(g5.1.5)totheONposition.
4 Press the right thumb control (fig 5.1.3) to start in a forward motion. You will very gently
accelerate.
5 Releasing the lever will automatically apply the brake and you will gently stop.
Practice these basic functions until you get used to them.
5.3.1 - Steering
Steering the scooter is easy and natural. Just be sure to remember to give wide clearance
when turning so that the rear wheels clear any obstacle. If you must steer in a tight spot,
such as entering a doorway or when turning around, stop, turn the handlebars to where
you want to go, then apply power gently. This will make the scooter turn very sharply, but
it will still go gently and with complete stability.
5.3.2 - Reversing
Reversing the scooter requires greater attention. Turn your Speed Adjustment Dial to slow
before you reverse (fig 5.1.1). Push the left Thumb Lever Control. Remember to turn your
steering column before applying power. Steer wide of all corners and obstacles.
5.4 - DISMOUNTING
Before dismounting, ALWAYS turn key to the OFF position.
1 Locate the seat lever and pull the lever up.
2 Swing the seat away ensuring it locks into position, and ease onto your feet.
CAUTION! - If you require steadying when mounting or dismounting the scooter, use the
armrests rather than the front tiller
6. GENERAL ADVICE
6.1 - CONTROL THROUGH OBSTACLES
The chances are that when you start really using your scooter you will meet some obstacles
that will require some practice to drive through smoothly. Here are some common obstacles,
with tips that will help master them quickly. You will soon be in control through heavy doors,
up and down ramps, up and over kerbs, through grass, gravel and up hills with surprising
ease by following these tips.
6.1.1 - Control Through Doors
Approach the door slowly. If the door opens away from you, hold the doorknob or bar in
one hand and apply the power with the other hand. If it is a self closing door, you can go
through allowing the door to close behind you. If not, just stop when you are clear of the

8Shoprider Scooters User Guide
door and push it closed. If the door opens towards you, hold the knob or bar with one
hand and gently press on your left thumb lever, and allow the gentle reverse power to
do the work. When the door is open wide enough, push the forward lever and go ahead
quickly, leaving your hand on the door to keep it free of the scooter and letting go as you
pass the doorjamb.
6.1.2 - Control on Ramps
Many public buildings have ramps for scooters access. Some have a turn in the middle, and
good cornering is required. Having stopped while facing uphill, starting up again simply
requires that you apply forward power.
Going down any ramp or hill, keep the speed adjustment dial set to “Slow’. This will keep
you in a safely controlled descent. If you wish to stop completely, simply release the thumb
control lever.
6.1.3 - Control Over Grass, Gravel and Hills
The Shoprider scooter performs admirably in grass, gravel and on hills. However, you must
notexceedtheguidelinessetdowninthisguide.Please,refertothesafetyprecautions
(page 2). Safety must always come first. If you are unsure about any situation, avoid it.
Feelfreetouseyourscooteronlawnsorinparkareas.Packedgravelsuchasondrive-ways
or roads will present no problem. Avoid long grass, loose deep gravel as well as loosely
packed sand. Because of the power of your scooter, you are able to climb steep hills, but
themaximumsafegradelimitis9°-thereasonforthisistoensureproperstability.Tryto
avoid wet weather and wet surfaces, rain or showers may cause electrical faults and wet
surfaces can become slippery.
6.2 - PARKING IN PUBLIC
If you need to park and leave the scooter, simply remove your key. This will keep the brake on
and will make your scooter difficult to move. It is best to leave it in sight of someone like a
shop assistant who can watch it for you.
7. MAINTENANCE
7.1 - WHEELS AND TYRES
All Shoprider Scooters have split rim wheels. This allows any puncture to be repaired with ease.
The TE 888iX has solid tyres, these do not get punctures and do not need to be inflated.
7.1.1 - Changing Wheels and Tyres
When changing a wheel, remove the centre bolt and then remove the wheel. Replace with
new/repairedwheelandre-boltthecentrebolttothehub.Whenchangingatyreyou
must deflate the tyre. Remove the centre bolt and the four lock nut bolts after deflation to
split the wheel.
7.1.2 - Tyre Pressure
The recommended tyre pressures are Front 25 psi and Rear 30 psi. The tyre pressure must
notexceed50psi(psi=poundspersquareinch).Tyrepressuresshouldbecheckedregularly.
CAUTION! - On the tyre itself it states that maximum tyre pressure is 50 psi.
Please, note that this is the maximum tyre pressure and the tyres should never
be inflated to this pressure.

Shoprider Scooters User Guide 9
7.2 - LUBRICATION
Atsixmonthintervalsyoushouldlubricatethefollowingpartswithalightoilorsimilar
lubricant:
• Seatpivotpost
• Seatreleaseleverpinion
• Wheelbearings
• Axleofscooter
CAUTION - Do not use WD40 to lubricate parts!! Do not lubricate transaxle/gear box!! In the
event of any difficulties please consult your dealer.
8. BATTERIES AND BATTERY CHARGING
8.1 - BATTERIES
The Shoprider Scooters are supplied with two sealed lead acid or gel maintenance free
batteries. These are fitted under the seat in the centre of the scooter. For easy handling,
Velcro carrying straps are provided to assist in fitting or removal. The range of the batteries
can be affected by temperature, terrain, battery condition, weight of user, etc. The battery
level indicator is only a guide and is most effective when the scooter is moving, only then is
the true discharge level displayed.
• Whenthescooterstopsthebatterylevelindicatormayindicatefull
• Anactiveusercanuseupto30%ofbatterycapacityormoreperday
• Inactiveusersmayonlyuse50%ofbatterycapacityinaweek
• Inboththeseinstancesthebatteryshouldbeputonchargeovernight
CAUTION! - Batteries should be kept fully charged at all times. They must not be left in a
discharged state if not used for some time.
8.2 - BATTERY CHARGING
Charge the batteries completely (8 - 12 hours) prior to first time use.
The batteries supplied with your scooter are specially designed and require an automatic
battery charger which is supplied with the scooter. All chargers are fitted with an electronic
switch that terminates the charge when the batteries are fully charged.
Tore-chargeyourscooterfollowtheprocedurebelow:
1 Turn the key to the OFF position
2 Plug the charger into the wall socket making sure the switch is in the OFF position
3 Insert the battery charger interconnect, three prong metal plug into the interconnect socket
on the right side of the tiller, at the top (fig 5.1.6)
4 TurnthepowerONatthepoweroutlet.TheREDlightonthebatterychargerwillletyou
knowthepowerisON,theGREENlightwillblinkonandofftoletyouknowthebatteryis
nowcharging.WhenthebatteryisfullychargedtheGREENlightwillstayon.
5 Everytime you use the scooter you should always put it on charge overnight, leave it on
charge overnight and turn the charger off in the morning. This will make sure that your
batteriesare100%fullychargedtogetthebestperformancefromyourbatteries.
CAUTION! - The charger is for indoor use only. Do not expose to rain or spray. Do not cover
the battery charging vent. Always ensure that the charging lead is in good condition and has
not been damaged or stretched.

10 Shoprider Scooters User Guide
9. TROUBLESHOOTING
9.1 - CIRCUIT BREAKER AND FUSE
Your scooter is fitted with controls that protect the electrical system from overloads. If your
scooter stops for no reason, it may be due to the circuit breaker. The circuit breaker can be
located through a hole on the top of the rear chassis cover. On rare occasions, there may be
an overload. If this occurs, the circuit breaker will pop out. To reset, turn the key to the OFF
position,pressthecircuitbreakerbuttonandthenturnthekeytotheONposition.
9.2 - IF THE SCOOTER DOES NOT RUN
• CheckthekeyisintheONposition.
• Checkthecircuitbreaker.
• Checkallplugsandconnectorsarermlyxed.
• Makesurethatthebatteryadapterisdisconnectedfromthechargerplug.
• Makesurethatthefreewheelingdeviceisintherunposition.
• Makesurethatthebatteriesarefullycharged
If the free wheel device has been operated with the scooter left switched on, then the scooter
will not operate until the ignition key has been switched off then on again. If after checking
these points your scooter is still not running, please contact your nearest authorised dealer.
10. WARRANTY INFORMATION
The Shoprider Scooter carries the following warranty against defects in materials
1. Chassis for a period of five years
2.Allcomponentsoftheunitforaperiodof18monthsexcludingbatteries,tyres,tubesandfuses
3. Batteries are covered by the battery manufacturers warranty.
Misuseofthescooter,operationnotinaccordancewiththeownersmanual,exceedingthe
load capacity or performance specification and modifications to the scooter by anyone without
approvalbyShopriderNZwillvoidthewarranty.Warrantyonlyappliestotheoriginalpurchaser.
Copy the following information from your dealer for future reference:
ModelNo. *SerialNo.
ChargerType&No.
Batterytype&No.
Your Shoprider Dealer
9. Troubleshooting
9.1
*Serial number located
on the rear chassis rail

108SawyersArmsRd,Papanui,Christchurch,NewZealand
Freephone:0800-220-110•Fax:[phone]•Email: [e-mail]
Your Shoprider Dealer