Showven SONICBOOM PLUS SMOKEJET User manual

USER MANUAL
SONICBOOM®PLUS SMOKEJET
V3.0
2022/05/11
Showven Technologies Co., Ltd.

Thanks for choosing SHOWVEN®SONICBOOM®PLUS smokejet, we wish it will bring you
lots of exciting moments.
Please read the following manual carefully before operating this product.
ΔSAFETY CONSIDERATIONS
\Unauthorized repair are prohibited, it may cause serious incident
\This product is not waterproof design, please keep it dry, please do not use it when there are
fog fluid leakage or wet from rain.
\Make sure power supply in consistent with the rated voltage of the equipment, and the socket
must well grounded. Unplug and turn off the machine when not use.
\For adult use only, keep it away from fire, inflammable and explosive articles.
\Installed in well ventilated area, ensure at least 50cm space around the machine, cover of the
nozzle is forbidden.
\If the machine fails to work, please stop operation and unplug the machine. Check fog fluid,
fuse, power connection etc. carefully, if can’t solve the problem, please contact SHOWVEN®
or your local SHOWVEN®partner for advise.
\Suggest use SHOWVEN®original FX-S fog fluid, other fluid may lead to clog or malfunction.
Please do not adding any other material such as pigment, water etc to the fuel bottle.
\To avoid fluid spill, make sure fog fluid not exceed related MAXIMUM fluid level line. When
install SONICBOOM®in invert direction, the fuel bottle should installed upward.
\In case of eye contact of fog fluid, please wash it with clean water. If fluid is swallowed
immediately look for medical advice.
ΔDescription
SONICBOOM®PLUS is new generation CO2jet simulator, derived from SONICBOOM®platform
but with dual smoke generation system and dual output design, to meet the high end
professional requirement for faster and denser vertical fog effects. With auto pressure control and
accumulator design ensure the better smoke column consistency.
ΔTechnical Specifications
\MODEL: SONICBOOM®PLUS
\DIMENSION: 500× 324× 325mm
\WEIGHT: 28kg
\VOLTAGE: 220V / 110V,50/60Hz
\FUSE: 15A/250V (220V),18A/250V (110V)
\POWER: 3000W/1800W(220V),2400W/1800W(110V)
\LED POWER: 9W× 38pcs
\MAX OUTPUT DISTANCE: 10m

\MAX CONTINUOUS OUTPUT DURATION: 10s
\OUTPUT: 80000cuft/min
\FLUID CONSUMPTION RATE: 3min/L
\TANK CAPACITY: 5L
\DMX CHANNEL: 1/11/14
\CONSUMABLES: FX-S
ΔStructure
2
1
4
5
6
8
1 0 91 11 2
3
7
1. Handle
2. Fluid Bottle
3. Foot
4. Output Nozzle
5. LED
6. LCD Screen
7. 3-PIN DMX
8. 5-PIN DMX
9. Power Socket
10. Fuse
11. Power Switch
12. Cooling Fan

ΔOperation Panel
1. Control button area
MENU: Short press to switch interface, press and hold for 3 seconds can switch to the advanced
setup interface
+: Parameters up; multiplex “TIMER” (smoke output time)
-: Parameters down; multiplex “VOLUME” (smoke output start)
ENTER Confirm and save parameters, screen will blink once when save successfully. multiplex
“STOP”.
NOTE: Screen will switch to main interface automatically if not press any button in about 15s.
Example of “TIMER” setting function in the menu:
1. “set interval 10s”
2. “set duration 2s”
Press “VOLUME” button under main interface, SONICBOOM®start to generate smoke, and will
repeat firing 2s, interval of 10s. Press “STOP” to stop the machine.
ΔInterface
1. Main interface:
First line: Display DMX address is “1”. “:” blinks when there is DMX IN signal.
Second line: Shows machine core temperature and pressure. The machine ready for operate only
when both temperature and pressure value close to 100%.
2. Error information
E1 Pressure Error
In order to protect pump, SONICBOOM®X with fuel detect function. When there is no fog fluid,
system can’t reach target pressure in the setting time after turn on machine, pump will stop
Error information
Explanation
E1 Pressure
Pressure faults, no fog fluid or pump error
E2 K temp. Sensor
Temperature sensor fault
E5 Temp Over
Circuit fault
E6 Heat Fail
Heating element damage or circuit fault or unstable
voltage