Showven SPARKULAR SPIN User manual

V1.0
SPARKULAR SPIN
USER MANUAL
Showven Technologies Co.,Ltd.

1
SPARKULAR SPIN
USER MANUAL
★Please read this manual carefully before operating this product.
★Warranty card attached in the manual, please keep it well.
Safety Information
》Never touch the nozzle of SPARKULAR SPIN, danger of getting burnt.
》Never touch the sparks which shooting out from the nozzle.
》Cover of nozzle of SPARKULAR SPIN is prohibited.
》Unauthorized repair are prohibited, it may cause serious incident.
》Keep the device dry, do NOT use in rain or snow.
》Make sure lid of feeding hopper are well covered when use SPARKULAR SPIN. Accidentally burning of Composite Ti
can only use sands to extinguish. Composite Ti should keep away from moisture and stored in a dry sealed environ
ment.
》Keep audience, animals or flammable objects at a minimum distance of 3m from SPARKULAR SPIN. Make sure
sparks shoot out from SPARKULAR SPIN can NOT touch any objects in the air.
》Please be noted that there may sparks or remains fall to the ground when use HC8200 LARGE. Suggest to use
HC8200 MEDIUM or SMALL when indoor.
》Clear material is necessary both before and after the show. Please check nozzle of SPARKULAR SPIN after each
show, if there are consumable agglomerated in the nozzle, please clear it with screwdriver, otherwise it will affect
the spark effects and even damage the machine.
》For better heat dissipation, block the air intake and air outlet is prohibited.
Description
SPARKULAR SPIN is another global pioneering SPARKULAR machine originally from SHOWVEN. With two 20° angled
nozzles and bidirectional rotatable structure, it creates the waltz-like lissome and romantic sparks. With adjustable
rotation direction, rotational speed and effect height, SPARKULAR SPIN bring a new visual effect to your events.

2
Technical Specifications
Product name SPARKULAR SPIN
Model BT81/BT82
Dimension 330x305x349mm
Weight 20Kg
Input AC220V,50/60Hz
AC110V,50/60Hz
Work Power 1000W
Hopper capacity 200g*2
HC8200 consumption rate 20g/Min*2
Work Temp. -20°C~40°C
Effect Height HC8200 LARGE: 2-5m adjustable
HC8200 MEDIUM: 2-4m adjustable
Casing Material 304 stainless steel
Interface NEUTRIK POWER IN/OUT, both 3-pin and 5-pin XLR
Control Wireless remote
DMX: 2 channel/ 4 channel for professional use
Operation Panel
LED display area:
READY: Flashing means heating up, about 5min. Turns from flashing into long on, indicates that the machine is ready
to work.
DMX: Flashing shows that DMX signal is connected, light OFF means there is no DMX signal
FAULT: Light ON when error occurs
HEAT: Light ON when system is heating up
READY DMX FAULT HEAT
Control Button Area:
MENU: switch through setup menu. Press 3s switch to advanced interface
DOWN: parameter down
UP: parameter up
ENTER: confirm and save parameters

3
Interface
Main interface:
Error information:
593
DMX 60.001
582 RPM 70
RFID area:
RFID card comes together with HC8200. It is a safety design, allows machine to identify the parameter and types of
consumable.
Please note that granules RFID card can increase the single machine specific working time. The card is disposable, can
only use once.
First Line: Shows inner core temp. of Nozzle 1, inner core temp. of Nozzle 2, Spinning speed respectively.
Second Line: DMX address, error info. If available, remain working time.
Error Informations Explanation
E0 System IC Systematic error
E2 Temp. Sensor Temperature sensor is not connected or damage
E3 P Temp. Over Chassis over-temperature
E4 Time Remain Activated time for machine is not enough, need to swip RFID card
E5 K Temp. Over Inner core over-temperature
E6 Heat Fail Heating fail, if it self recovery, please pay attention to the power supply.

4
Setting Menu:
Press “MENU”switch through setup menu.
Set DMX Address
Wireless Remote
Manual Fountain
Fountain Height
1-512
ON/OFF
ON/OFF
1-10
Set DMX address If controlled by Host Controller, please set DMX address as
1, 3, 5, 7,…2n-1, otherwise it may leads to signal interference
Wireless function ON/OFF
Manual firing ON/OFF, for test only
Manual firing height setup, for test only
Spin Speed 60-100 Spinning speed setup
LCD Backlight ON/OFF LCD light ON/OFF
Advanced Menu:
Press “MENU” 3 seconds to enter the advanced setup interface, press MENU key to enter different options,
wait 3 seconds to return to the main interface.
Options
Set Temperature
Auto Heat
Density
Range
ON/OFF
ON/OFF
1-10
Explanation
Wireless function ON/OFF
Manual firing ON/OFF, for test only
Manual firing height setup, for test only
Mode Selection Factory Mode
User Mode
Factory mode is for engineer only. When in Factory mode machine can’t
controlled by DMX console/host controller
DMX Channel Mode 2 Channel
4 Channel Channel mode set. 4 channel is for professional control with lighting console
Standby Switch ON/OFF Standby function. When ON, the machine can firing only when heating up
was finished

5
DMX channel – 2 channel mode:
First channel
(both nozzle) Function
0-15 Fountain OFF
16-39 Height Low, not spin (related firing height on HOST CONTROL is 1)
40-63 Height Middle, not spin (related firing height on HOST CONTROL is 2)
64-87 Height High, not spin (related firing height on HOST CONTROL is 3)
88-111 Height Low, Clockwise spin (related firing height on HOST CONTROL is 4)
112-135 Height Middle, Clockwise spin (related firing height on HOST CONTROL is 5)
136-159 Height High, Clockwise spin (related firing height on HOST CONTROL is 6)
160-183 Height Low, anticlockwise spin (related firing height on HOST CONTROL is 7)
184-207 Height Middle, anticlockwise spin (related firing height on HOST CONTROL is 8)
208-231 Height High, anticlockwise spin (related firing height on HOST CONTROL is 9)
232-255 Height High, anticlockwise spin (related firing height on HOST CONTROL is 10)
Second channel
(both nozzle) Function
60-80 Clear Material (perform after each show)
20-40 Emergency Stop
0-10 Pre-heat OFF (disabled when auto-heat ON)
240-255 Pre-heat ON (disabled when auto-heat ON)

6
DMX channel – 4 channel mode:
First channel (Nozzle 1) Function
0-15 Nozzle 1 Fountain OFF
16-255 Nozzle 1 effect height adjust
Second channel (Status) Function
60-80 Clear Material (perform after each show)
20-40 Emergency Stop
0-10 Pre-heat OFF (disabled when auto-heat ON)
240-255 Pre-heat ON (disabled when auto-heat ON)
Third Channel (Nozzel 2) Function
0-15 Nozzle 2 Fountain OFF
16-255 Nozzle 2 effect height adjust
Fourth Channel(Spinning Control) Function
136-255 Anticlockwise spin, spin speed adjust (60-100RPM）
16-135 Clockwise spin, spin speed ajust（60-100RPM）
0-15 Not spin

7
》Choose DMX 2 channel mode when use SHOWVEN original host controller. Please follow belowing rules to set DMX
address, otherwise it may leads to signal interference.
》When control by PROGO remote control, please set the spinning speed on device, it can’t change on remote control.
Button function on PROGO remote control as below:
First button: FOUNTAIN OFF / Match with device
Second button: Height High
Third button: Height Middle
Fourth button: Height Low
Note: Press the first button to match device with remote control within 5s when turn on the SPARKULAR SPIN. If it
is not work after match with machine please check the battery status of remote control.
DMX Address
Sparkular No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35

8
Tel:
Warranty Instructions
Warranty Card
★ Below situations NOT included in warranty service:
★ Invoice and warranty card are necessary when applying for maintenance service from
SHOWVEN.
▲ Sincere thanks for your choosing SPARKULAR SPIN, you will receive quality service from us.
▲ The product warranty period is one year. If there are any quality problems within 7 days after shipping out from our
factory, we can exchange a brand new same model machine for you.
▲ We will offer free of charge maintenance service for machines which with hardware malfunction (except for the
instrument damage caused by human factors)in warranty period. Please don't repair machine without factory
permission.
1. Damage caused by improper transportation, usage, management, and maintenance, or damage caused by human
factors;
2. Disassemble, modify or repair products without Showven’s permission;
3. Damage caused by external reasons (lightning strike, power supply etc);
4. Damage caused by improper installation or use;
For product damage not included in warranty range, we can provide paid service.
Product Name:
Purchase Date:
Address:
Problem Feedback:
Maintenance Detail:
Service Engineer:
Actual Problem:
Serial No.
Service Date:

Showven Technologies Co., Ltd.
Add: BuildingB1,ChangshaECenterNo.18,XiangtaiRoad,LiuyangEconomicDevelopment
Zone,ChangshaCity,410300,HunanProvince,P.R.China.
Tel: [phone]
Web: www.showven.cn
E-mail: [email protected]