Showven SPARKULAR FALL User manual

USER MANUAL
SPARKULAR FALL
V1.0
2021/03/30
Showven Technologies Co., Ltd

USER MANUAL
SPARKULAR FALL
★Please read this manual carefully before operating this product.
★Warranty card attached in the manual, please keep it well.
▲SAFETY CONSIDERATIONS
\ Never touch the nozzle of SPARKULAR FALL, danger of getting burnt
\ Never touch the sparks which shooting out from the nozzle
\ Unauthorized repair are prohibited, it may cause serious incident
\ Keep SPARKULAR FALL dry and do NOT use in rain or snow
\ Make sure lid of feeding hopper are well covered when use Sparkular Fall. Accidentally
Burning of Composite Ti can only use sands to extinguish. Composite Ti should keep away from
moisture and stored in a dry sealed environment
\ Keep audience and flammable material at a minimum distance of 3m from SPARKULAR FALL
and it’s drop sparks. Make sure sparks shoot out from Sparkular FALL can NOT touch any
objects
\ Ensure that children, animals and unauthorized persons don’t have access to the SPARKULAR
FALL
\ Clear material for Sparkular Fall is necessary both before the show and after the show, to
clear the Composite Ti remains in the pipe. Check whether there are Composite Ti aggregate in
the nozzle after each show, if any, please clean it up, or it will affect the shooting effect or
even damage Sparkular Fall
\ The Sparkular FALL power supply cable (sparkular fall power supply EX-cable) maximum
allowed cascade for Sparkular Fall is 6pcs (BT04)/ 3pcs (BT05), exceeded connecting may result
in damage or even cause fire
\ For better heat dissipation, block the air intake and air outlet is prohibited
\ Cover of nozzle of Sparkular Fall is prohibited
▲Description
SPARKULAR FALL is hanging special effects equipment for indoor/outdoor use to generate daz
zling silver “waterfall” sparks effects. According to different usage scenarios, operator can self
define various types of “water curtain” effects vary from 2m to 7m by use of different types of
HC8200.

▲Technical Specifications
\ MODEL: BT04/BT05
\DIMENSION: 196×208×192mm
\ WEIGHT: 6.0kg
\ VOLTAGE: 220V(BT04)/110V(BT05), 50/60Hz
\ WORK POWER: 500W
\ EFFECT HEIGHT: 2-7m(according to HC8200 type)
\ INTERFACE:3-pin XLR, POWER IN/OUT
\ CONTROL: DMX 2 channels, Wireless Remote
\ ADAPTABLE TRUSS SIZE: 40-60mm
▲Operation Panel
1. LED display area:
READY DMX FAU LT HEAT
READY: After turning on machine, it will automatically preheat around 5 minutes, when the
"READY" green light turns from flashing into long on, indicates that the machine is ready to
work
DMX: Flashing shows that DMX signal is connected, otherwise is without signal
FAULT: When any malfunction , the light turns on
HEAT: When the machine is heating, signal light turns on
2. Control button area:
MENU short press to switch interface, press for 3 seconds can switch to the advanced setup
interface
-: Parameters down
+: Parameters up
ENTER Confirm and save parameters.

3. Bottom Indication Light
Off: Sparking or Not in preheating
Quick Flashing: Preheating
Long on: Preheated
Slow Flashing: Error warning
3. RFID area:
Composite Ti with RFID card, swiping cards used to identify parameters and types of granules.
Please note that granules RFID card can increase the single machine
specific working time. The card is disposable,one card can only use one time
▲Interface
1. Main Interface:
First line: Display DMX address is “1”
Second line: Display the present inner core temperature and the temperature progress bar;
displays remianing time is 7 minutes and 24 seconds

2. Error information:
3. Setting Menu:
Press “MENU” to enter the Setting interface, press the “MENU” button to enter different
options until you return to the main interface
4. Advanced Menu:
Press “MENU” 3 seconds to enter the advanced setup interface, press MENU key to enter
different options, wait 3 seconds to return to the main interface
Error information
Explanation
E0 System IC
Systematic error
E2 Temp. Sensor
Temperature sensor was damaged
E3 P Temp. Over
Chassis temperature is too high to shut
down
E4 Time Remain
Insufficient granules or remaining time,
please swiping time card
E5 K Temp. Over
Inner core temperature is too high to shut
down
E6 Heat Fail
Heating failed
Options
Range
Explanation
Set DMX Address
1-512
Set the DMX address, machine become a
wireless host and can
send out DMX signal when its address is
“1++”
Wireless Control
ON/OFF
Wireless function switch, you can match
code when shows “ON”
Manual Fountain
ON/OFF
Manual fountain switch , for testing
purposes only
Options
Range
Explanation
Set Temperature
500-610
Setup inner Core temperature
Auto Heat
ON/OFF
Auto preheat function switch after turn on
machine
Density
70-100
Adjust the sparks density
Mode Selection
Factory Mode
User Mode
Factory Mode is factory debugging mode,
User Mode is using mode
Default Parameter
Press “ENTER” to restore all parameters to
the factory settings

▲Use
1. Power cable connection
For convenient use, there are power supply cable and power supply ex-cable. Power Supply ex-
cable can achieve multiple devices connected, maximum cascade is 6pcs(BT04)/3pcs(BT05). All
power plugs are industrial plug with lock, it need to toggle snap and rotate when using
2. Host controller mode
Using the host controller to moniter the working status of Sparkular Fall to achieve multiple
dynamic effects and stable controlling.Sparkular Fall has high/low level the height settings 1-5
in host controller is low level,6-10 is high level.Please see the details in host controller manual.
3. Cable DMX mode
When using the DMX controller, the system takes 2 channels
The First channel
Functions
0-15
Firing OFF
16-135
Low Level Fountain ON
136-255
High Level Fountain ON
The second channel
Functions
60-80
Clear Material
20-40
Emergency Stop
0-10
Pre-heat OFF(Disable in Auto-heat)
240-255
Pre-heat ON(Disable in Auto-heat)
4. Wireless remote control mode
If the remote control cannot work, please check whether wireless function was turn on. Press
MENU to switch to wireless control setting , menu is set to ON , press ENTER . In this
interface, you can also match code with remote controller
Sparkular Fall can controlled by both DMX and remote controller, when there are DMX signal
input, wireless remote controller will not work.
When using remote controller you need to pull out the antenna.
After pressing set button,press 3 on button immediately to change to low level press
3 off to change to high level.

1 ON
Address “1” ON
1 OFF
Address “1” OFF
2 ON
Address “3” ON
2 OFF
Address “3” OFF
3 ON
Address “5” ON
（Low Level）
3 OFF
Address “5” OFF
（High Level）
Set
◆When use
different remote
controller
◆Change Levels
CLEAR
◆Automatically
clean material for 3
seconds
◆Start Pre-heat
5S
All Starts 5 seconds
15S
All Starts 15 seconds
30S
All Starts 30
seconds
OFF
All stop
Attention: The first group machines correspond to DMX address “1”, the second group DMX
address is “3”, the third DMX address is “5”, remote controller controls 3 groups of machines.
You can also set all Sparkular Fall address as “1”
When the lamp is not lit or becomes weak on the remote controller, please replace the battery.
It is better to take battery out when transporting to prevent consumption of battery power by
unmeant press of button Battery model 12V 23A
When the machine is occasionally not working, may be caused by interference, please press the
start button again
Wireless control is easily influenced by interference, it suggests to stay as close to machine as
possible when use remote controller, and machines cannot use metal shielding
5. Wireless host Sparkular Fall mode (requires communication cables):
In occasion of strong interference, using the wireless host can avoid interference, ensure
stable control. Enter into Set DMX Address option menu,press “-”when the DMX address is
“1”to set the first unit of Sparkular Fall’s DMX address into “1++”, this machine address is “1”,
but it can also output DMX signal and turns into wireless host Sparkular Fall. Use
communication cables to connect all the Sparkular Fall, the host Sparkular Fall will receive the
signal from remote controller and transfer to all other Sparkular Fall via communication cables
to realize stable signal transmission
Attention: In this mode,please don’t connect to other controll mode to prevent from
communication disorder

HC8200
Fall length(Low Level)
Fall length(High Level)
MEDIUM
2m
3m
LARGE
3m
4m
LARGE-Ⅰ
4m
5m
LARGE-Ⅱ
5m
7m

Warranty Instructions
▲Sincere thanks for your choosing our products, you will receive quality service from us
▲The product warranty period is one year. If there are any quality problems within 7
days after shipping out from our factory, we can exchange a brand new same model
machine for you
▲We will offer free of charge maintenance service for machines which with hardware
malfunction (except for the instrument damage caused by human factors)in warranty
period. Please don't repair machine without factory permission
Below situations NOT included in warranty service:
1. Damage caused by improper transportation, usage, management, and maintenance, or
damage caused by human factors;
2. Disassemble, modify or repair products without permission;
3. Damage caused by external reasons (lightning strike, power supply etc.)
4. Damage caused by improper installation or use;
For product damage not included in warranty range, we can provide paid service.
Invoice and warranty card are necessary when applying for maintenance service from
SHOWVEN.
Warranty Card
Product Name:
Serial No.
Purchase Date:
Tel:
Address:
Info. feedback
about the
problem:
Actual problem:
Maintenance
detail:
Service Engineer:
Service Date:

Showven Technologies Co., Ltd.
Tel: [phone]
Web: www.showven.cn E-mail: [e-mail]
Add: Liuyang Economic Development Zone, Changsha, 410300, Hunan Province,
P.R.China