Shure SCL3 User manual

SCL3
Sound Isolating Earphones
With a sleek, low prole design,
the SCL3 combines WideBand
MicroDriver technology and
incredible sound isolation for
detailed highs
and enhanced
bass across an
extended frequency
soundstage.
Originally designed
for the demanding
audio specications
of professional
musicians, the SCL3
is an ideal choice for any
home or portable audio
device.
�
INSERTING THE EARPHONES
If the earphone seems to be lacking in low frequency response (bass), check
the tightness of the seal between the earphone and your ear, or try one of the
other sleeve options.
Warning: Do not push the earphone sleeve beyond the ear canal opening.
WEARING THE EARPHONES
Three popular methods for wearing the earphones are illustrated below.
CHOOSING AN EARPHONE SLEEVE
Your earphones come with a selection of sleeves. Make sure the sleeve you
use is easy to insert into your ear, ts comfortably, and is easy to remove from
your ear.
CLEANING THE EARPHONE NOZZLE
If the nozzle of your earphone is blocked, clean the nozzle using the supplied
wax removal loop.
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: [phone] U.S. Fax: [phone] Int’l Fax: [phone]
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: [phone] Fax: [phone]
Asia, Pacic:
Shure Asia Limited, Phone: [phone] Fax: [phone]
Triple-Flange Sleeves (Optional Accessory)
If desired, the sleeve nozzle may be shortened. Use sharp
scissors to carefully trim the nozzle to the desired length.
Yellow and Soft Black Foam Sleeves
When using the foam sleeves, compress the sleeve between
your ngers before inserting it into the ear canal. Hold the
earphone in place for about ten seconds while the foam
expands and creates a tight seal. Black foams come in
small, medium and large sizes.
Soft Flex Sleeves
In small, medium, and large sizes. Made from pliable
rubber.
Nozzle
Wax Removal Loop
Tighten the cable and take up slack by raising the cable sleeve .
When cleaning, do not force any object through the earphone nozzle! This will
damage the earphone sound lter.
©2007, Shure Incorporated
27EN3249 (Rev. 1)
Printed in U.S.A.
Over the ear
in back Over the ear
in front
Straight down
left ear right ear
Note: slide sleeve over earphone nozzle barb for a secure grip.
To change earphone sleeve, twist and pull sleeve to remove it from the nozzle. Push new sleeve
onto nozzle until you feel it slide completely over barb. If any part of the nozzle is exposed,
sleeve is not properly installed. Replace sleeves if they do not grip the nozzle tightly.
Nozzle Barb Sleeve Sleeve Over Barb
Warning: The wax removal loop is only to be used to clean
earphones. Any other use, such as using the tool to clean
ears, could result in injury.

CUSTOM EARPHONE SLEEVES
Those who use earphones regularly for extended periods of time often nd
custom-t molded sleeves offer the best comfort and sound isolation.
Ask a Hearing Health Care Professional about creating custom molded
sleeves for your earphones. For more information, contact:
FURNISHED ACCESSORIES
• Deluxe Carrying Case
• Fit Kit: contains foam, soft ex and triple ange sleeves plus cleaning tool
Sensaphonics Hearing Conservation Toll Free: [phone]
660 N. Milwaukee Avenue In Chicago: [phone] (ph)
Chicago, IL 60622
e-mail:[email protected]
www.sensaphonics.com
TECHNICAL SPECIFICATIONS
Transducer type Low mass/high energy
Sensitivity (at 1kHz) 113.5 dB SPL/mW
Impedance (at 1kHz) 29 W
Output connector Gold-plated 3.5 mm (1/8-inch) stereo plug
Cable length GR -157 cm (62”)
W -157 cm (62”)
K -141 cm (56”)
Net weight 28 g (0.9 oz)
ACCESSORIES
For information about earphone accessories (listed below) and other Shure
products visit: www.shure.com
• Replacement Sleeves • Extension Cables
• Carrying Cases • Push To Hear (PTH)
• Adapters • Volume Control
CERTIFICATION
Eligible to bear CE marking.
Conforms to European EMC Directive 89/336/EEC.
Meets applicable tests and performance criteria in European Standard
EN 55103 (1996) Parts 1 and 2, for residential (E1) and light industrial (E2)
environments.
MAINTENANCE
Careful maintenance ensures a tight seal between the sleeve and nozzle,
improving sound quality and product safety.
Keep the earphones and sleeves as clean and dry as possible.

To clean sleeves, remove them from earphones, gently rinse in warm
water and air dry. Foam sleeves require a longer drying time. Inspect for
damage and replace if necessary.
Ear sleeves must be completely dry before reusing.
Wipe the earphones and sleeves with mild antiseptic to avoid infections.
Do not use alcohol-based disinfectants.
Do not expose earphones to extreme temperatures.
Replace sleeves if they do not t properly.
xDo not attempt to modify this product. Doing so will void the warranty
and could result in personal injury and/or product failure.