Shure SM35-TQG User manual

SM35
Performance Headset Condenser Microphone
The Shure headworn electret condenser microphone, SM35, user guide.
Version: 3.0 (2022-F)

Shure Incorporated
2/6
Table of Contents
SM35 Performance Headset Condenser Microphone 3
SM35 Headworn Microphone 3
Wearing the Microphone 3
RPM400 Preamplifiers 4
Features 4
Certifications 4
Specifications 4
Accessories 6
Furnished Accessories 6
Replacement Parts 6

Shure Incorporated
3/6
1.
2.
3.
SM35 
Performance Headset Condenser Microphone
SM35 Headworn Microphone
The Shure SM35 is a headworn electret condenser microphone, intended for use with a wireless bodypack transmitter in live
stage performances.
Wearing the Microphone
Install the windscreen on the microphone boom.
Place the headband around the back of the head, with the boom on the left side.
Place the microphone at the corner of the mouth. To decrease pops and plosives, avoid placing the microphone directly
in front of the mouth

Shure Incorporated
4/6
•
•
•
•
Note: Do not store the microphone in damp, enclosed spaces. Allow perspiration to dry completely before storing.
RPM400 Preamplifiers
The RPM400 preamplifiers offer exceptional dynamic range utilizing an active gain circuit in a concise and small package.
They are offered in two connector versions: TA4F and LEMO, which allows you to quickly take a wireless TL microphone and
make it a wired solution. These preamplifiers require phantom power and can efficiently operate across a wide range of supply
voltages from 12-48v.
Features
Active circuit design with neutral gain mimics wireless for consistent gain output across wired or wireless applications.
High RF immunity against unwanted interference.
Short, compact design.
Belt clip and table mounting kits for easy placement for a variety of applications.
Certifications
Note: Testingisbasedontheuseofsuppliedandrecommendedcabletypes.Theuseofotherthanshielded(screened)cabletypesmaydegradeEMCper
formance.
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Global Compliance
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: [phone]
Email: [email protected]
www.shure.com
Specifications
Type
Electret Condenser
Frequency Response
40Hzto20,000Hz

Shure Incorporated
5/6
Polar Pattern
Unidirectional (Cardioid)
Output Impedance
100Ω,@1kHz
Sensitivity
57.8dBV/Pa,@1kHz,1000Ωload
Signal-To-Noise Ratio [1]
59.2dB,@1kHz,1000Ωload
Maximum SPL [1]
151.3dB,1000Ωload,@1kHz,1%THD
Dynamic Range [1]
116.5dB,@1kHz,1000Ωload
Self Noise [1]
34.8dBSPLA,1000Ωload
Power Requirements
TA4F +5VDC(nominal),10Vmaximum(DCbias)
XLR connector 12to52VDC,phantompower
Polarity
TA4F Positive pressure on diaphragm produces positive
voltage on pin 3 with respect to pin 1
XLR Positive pressure on diaphragm produces positive
voltage on pin 2 with respect to pin 3
Cable
1.1m (45in.)
Connector
TA4F or XLR
Weight
72g(2.53oz.)
[1] Measurements taken using RPM400 preamp
*All specifications measured with a 48 Vdc phantom power supply. The microphone operates at lower voltages, but with slightly
decreased headroom and sensitivity.