Shure UNIDYNE 580SA User manual

222 HARTREY AVE.. EVANSTON. IL. 60204 U.S.A.
MODELS 580SA
AREA CODE 312/866.2200 . CABLE: SHUREMICRO
SHEET and 580SB UNIDYNEB A
TWX: 910-231.0048 TELEX: 72-4381 1 DATA
I
UNIDIRECTIONAL DYNAMIC MICROPHONES
GENERAL
The Model 580 Series UNIDYNEB A Microphones are
moving coil dynamic units built to provide wide range
reproduction of music and voice and featuring an ex-
cellent unidirectional microphone pickup pattern. These
unidirectional microphones are ideal for quality public
address, theater-stage sound systems, recording, and
other sound reinforcement applications.
Microphone Features:
rn
Exceptional true cardioid pickup pattern: sym-
metrical about axis and uniform at all frequen-
cies-providing highly effective suppression of
feedback
rn Uniform shaped response, particularly suitable
for the professional entertainer
rn A built-in On-Off switch with provisions for lock-
ing switch in its On position
rn
Versatility-for use in the hand or on a stand-
for use indoors or outdoors
rn
Dependability under all operating conditions
The Model 580 Microphones are supplied with an
adjustable swivel adapter which permits the micro-
phone to be tilted through 90" from vertical to hori-
zontal. This swivel also allows for "quick-disengage"
for use as a hand microphone.
Model 580SA is high impedance for connection to
high-impedance microphone inputs.
Model 580SB is low impedance for connection to
microphone inputs rated at 19 to 300 ohms. The low-
impedance microphone is recommended where long
cable lengths are required or under conditions of se-
vere hum disturbance. The permissible cable length is
practically unlimited since neither response nor level
is appreciably affected by long cables. Shure Model
A95 Series Line Matching Transformers are available
for use in those cases where a low-impedance micro-
phone line is desirable but the associated amplifier
has a high-impedance input. These transiormers pro-
vide a proper impedance match between a 19 to 300
ohm microphone line and a high-impedance input and
are available with various input and output connectors.
SPECIFICATIONS
TYpe
Dynamic
Frequency Response
50 to 13,000 Hz (see Figure 1)
+20
m
- +I0
-
Y
Z
g O
L
Y
5 -I0
Y L
-20
20
Y) 100 lUm0 10.000 20.003
FREWENCY IN HERTZ
TYPICAL FREQUENCY RESPONSE
FIGURE 1
Polar Pattern
Cardioid (unidirectional)-uniform with frequency,
symmetrical about axis (see Figure
2)
FIGURE 2
Impedance
Model 580SA: Microphone impedance is "High" for
connection to high-impedance microphone inputs.
Model 580SB: Microphone rating impedance is 150
ohms (160 ohms actual) for connection to micro-
phone inputs rated at 19 to 300 ohms.
Output Level (at 1,000
Hz)
580SA 580SB
Open Circuit Voltage*
.. . . . -57.5 dB -80.0 dB
(1.33 mV) (.I00 mV)
Power Level ** . .. . . . .... . .
-58.0 dB
*O dB = 1 volt per microbar
**O dB = 1 milliwatt per 10 microbars
Switch
Built-in On-Off switch with lockplate. To lock switch
in On position, remove screw on lockplate and turn
lockplate 180". Reassemble and tighten screw.
Cartridge Shock Mount
Internal rubber vibration-isolator
Cable
Model 580SA: 4.6m (15 ft), nondetachable, single-
conductor shielded
Model 580SB: 4.6m (15 ft), nondetachable, two-
conductor shielded
Copyright 1979, Shure Brothers Inc
27A325 (SK)
U.S. Patents 3,132,713 and 3,240,883
Printed in U.S.A.

Swivel Adapter
Positive action, adjustable through 90" from vertical
to horizontal, permits easy removal for handheld use,
suitable for mounting on stand with %"-27 thread
Case
Chrome-plated die casting and ARMO-DUR@ with
stainless steel grille
Dimensions
See Figure 3
169 rnrn
7 (6- 21/32 IN1 1
OVERALL DIMENSIONS
FIGURE 3
Net Weight
624 grams (1 Ib, 6 oz)
Packaged Weight
907 grams (2 Ib)
PHASING
To test two microphones for proper phasing, con-
nect them to an amplifier and talk or sing into them
while holding them three or four inches apart. The
sound from the speakers should be the same when
talking into either microphone or directly between them
if they are in phase with each other. If the sound drops
drastically, or if a dead spot is found when talking
between the two microphones, the microphones are
out of phase. All microphones should be tested in this
manner to insure that they are in phasewith each other.
To change the phase of a low-impedance micro-
phone at the equipment end of the cable, interchange
the BLACK and WHITE cable leads where they are
connected to the sound system. To change the phase
of a microphone, the microphone cartridge leads must
be interchanged (see Figure 4). This should be per-
formed by your dealer, the Shure Factory Service De-
partment, or other qualified service personnel.
CARTRIDGE
-L~~~~~ TERMINAL FC ASE
POSITIVE PRESSURE PRODUCES POSITIVE VOLTAGE
ON CABLE SHIELD
MODEL 580SA INTERNAL CONNECTIONS
jSWITCH SHOWN IN
"0FFWPOSITION
SHIELD
,-----
WHITE ! ':
-1
I .!I BLACK I /
LY
CARTRIDGE +ASE
POSITIVE PRESSURE PRODUCES POSITIVE VOLTAGE
ON BLACK CABLE LEAD
MODEL 580SB INTERNAL CONNECTIONS
FIGURE 4
FURNISHED ACCESSORY
............................
Swivel Adapter .A25B
OPTIONAL ACCESSORIES
Windscreen ............................... A6lWS
Line Matching Transformer ............. .A95 Series
Desk Stand
......... .S33B, S37A, S38B, S39A, S40A
Quick Disconnect Adapter ..................... A45
Dual Mount
............................... .A26M
REPLACEMENT PARTS
580SA 580SB
.....................
Cartridge R58 R58
.....
Screen and Grille Assembly RK51G RK51G
.................
On-Off Switch RK48S RK48S
ARCHITECTS' SPECIFICATIONS
The microphone shall be a moving coil (dynamic)
type with a frequency response of 50 to 13,000
Hz. The
unit shall have a cardioid polar characteristic. The
cancellation at the sides shall be approximately 6 dB,
and the cancellation at the rear shall be 15 to 20 dB.
Model 580SA shall be high impedance for connec-
tion to high-impedance microphone inputs.
Model 580SB shall be low impedance with a rated
impedance of 150 ohms for connection to microphone
inputs rated at 19 to 300 ohms.
The microphone output shall be:
...................
Model 580SA -57.5 dB
(0 dB = 1 volt per microbar)
...................
Model 580SB -58.0 dB
(0 dB = 1 milliwatt per 10 microbars)
The microphone shall be equipped with a built-in
On-Off switch and a nondetachable 4.6m (15 ft) cable.
The cable for Model 580SA shall be single-conductor
shielded; the cable for Model 580SB shall be two-
conductor shielded.
The microphone shall be provided with a swivel
adapter, adjustable through 90" from vertical to hori-
zontal, and suitable for mounting on a stand having
a %"-27 thread.
The overall dimensions of the microphone shall be
169 mm (6-21132 in.) in length and 46 mm (1-13116 in.)
in diameter.
The microphone shall be the Shure Model 580SA,
580SB, or equivalent.
GUARANTEE
This Shure product is guaranteed in normal use to
be free from electrical and mechanical defects for a
period of one year from date of purchase. Please
retain proof of purchase date. This guarantee includes
all parts and labor. This guarantee is in lieu of any
and all other guarantees or warranties, express or
implied, and there shall be no recovery for any con-
sequential or incidental damages.
SHIPPING INSTRUCTIONS
Carefully repack the unit and return it prepaid to:
Shure Brothers Incorporated
Attention: Service Department
1501 West Shure Drive
Arlington Heights, Illinois 60004
If outside the United States, return the unit to your
dealer or Authorized Shure Service Center for repair.
The unit will be returned to you prepaid.