SIBELL IPOD-SB3IREV Operating and maintenance instructions

Package
Overview
Installation
1
2
34
►Connecting Network Cable
2
13
* 1 It is recommended to install the Security cap for network cable connection.
* 2 If the PoE network switch is used to connect the camera, DC12V power supply
is not required.
①Loosen the nut from the main element.
②Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
Thank you for purchasing Sibell. We are always looking to
improve and will update the products or procedures as technology
changes and the industry adapts. If you need further product
assistance please contact your technical support specialist.
Content is subject to change without notice.*.
Warning and Caution
■If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We will not be responsible for any problems
caused by unauthorized repair or maintenance.)
■Keep away from liquid while in use, due to risks of electric shock
■When using this product, you must be in compliance with the
electrical safety regulations of the region. When the product is mounted
on wall or ceiling, the device should be secured firmly.
■Do not use camera beyond specified voltage range.
■Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■If cleaning is necessary, please use clean cloth to wipe it gently.
If the device will not be used for a long time, please cover the lens
cap to protect the device from dirt.
■Do not aim the camera at the sun or extra bright places.
■Do not place the camera in extreme hot or cold temps (the operating
temperature shall be -20˚C~50˚C), dusty or damp locations, and do
not expose it to high electromagnetism radiation.
■To avoid heat accumulation, good ventilation is required for
operating environment.
■Regular Maintenance is recommended for all devices
Quick Start Guide
Network Camera
Camera Quick start guide
CD Security cap Plastic plug ×3
Drill template
Rubber plug Screwdriver
3 tapping screws PA 4×25
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install and use the
camera in a dry environment. Advised: If lens cover is removed, re-
apply the cover within 4 hours.
① Drill the screw holes and the cable hole on the wall according to
the drill template.
Focus
Zoom
Focus
Zoom
∅130.7
∅119.5
∅4.5
120°
120°
103.5 mm
59.7mm
29.9mm
Network Cable
Zoom
Focus
1
2
3
4
②Route the cables and connect the power cable and network cable.
And then secure the camera to the ceiling or wall with the screws.
Power Cable
3
4
Foc us
Zoo m
12
DC12V
Network Cable
Focus
Zoom
To Use Security Cap: you must have experience in cable termination

MENU
MENU
IPC
IPC
Network Cable Network Cable
Network Cable
Switch
Router Computer
Computer
●Access the camera through IP-Tool
Rubber Plug
Lock Screw
Focus
Zoom
Focus
Zoom
Focus
Zoom
③Adjust the camera to obtain an optimum angle by loosening the
lock screws. Before adjustment, preview the image of the camera
on a monitor. Tighten the lock screws after you finish adjusting the
view angle of the camera.
Focus
Zoom
④ Adjust the Zoom screw and the Focus screw with the screwdriver
until you get the optimum image (if the camera you get is fixed lens,
please skip this step).
Foc us
Focus
Zoom
Focus
Zoom
Zoo m
⑤Remove the protection film gently to finish the installation.
Focus
Zoom
5IE Network Connection
●SECTION 1: Accessing the camera using the IP Tool
1.**Default Network settings for the camera are:
IP address: 192.168.226.201
Subnet Mask 255.255.255.0
Gateway: 192.168.226.1
2. Connect the IP camera and a Windows computer to a network switch
or router
3. Find IPTool on the CD, and install it on the computer.
4. Determine what the local network scheme is.
Device Network Search
Imme dia te Refr esh
name
name
name
IPC
IPC
IPC
unkn ow n
unkn ow n
unkn ow n
192. 16 8.226.2 01
192. 16 8.1.2
192. 16 8.1.3
80
80
80
9008
9008
9008
255. 25 5.
255. 25 5.
255. 25 5.
Modi fy N etwork Pa ra meter
Mac Add re ss
IP Address
Modi fy
CE :98 : 23 : 75 :35 :22
192 .1 68 . 2 26 . 201
255 . 25 5 . 25 5 . 0
192 .1 68 . 2 26 . 1
i
Tip : En ter the a dm inistra to r passw or d, and
then m od ify the net wo rk para me te rs.
Total De vi ce: 3 Loca l IP Ad dr es s:192 .16 8.1.4Subnet M as k:255 .25 5.2 55.0 Gate wa y: 192.168 .1.1 DN S：210.21 .19 6.6
Devi ce N ame Device Type IP Address Http P or t Data P or t Subnet
Prod uc t Model
Abou t
Subn et M ask
Gate wa y
Restore IPC Default Configuration
5. Type IPCONFIG within the console > Press Enter
6. Listed is LOCAL AREA CONNECTION with an IP address/Subnet
Mask/Default Gateway
7. Write down the information for local area connection displayed in
Command prompt
8. Double-click to open the IP search tool
9. Under Modify network parameter, change the first 3 DIGITS
(OCTETS) OF THE IP ADDRESS TO MATCH THE NETWORK
SCHEME FROM STEP 5 ABOVE. THE LAST OCTET WILL BE A
DIFFERENT NUMBER, YOU MUST CHOOSE AN IP ADDRESS
THAT IS AVAILABLE ON THE NETWORK TO PREVENT A
CONFLICT. Use the PING command in the command prompt to find
and available IP address.
**ex. C:\user\desktop> ping 192.168.1.199 If the ping “request times
out”, or “destination host unavailable” then the IP address is available for
use.
10. Proceed to enter in the available IP address, and use the same subnet
mask and Default Gateway from step 5
11. Type in the password of the camera:
DEFAULT PW: 123456 > Click MODIFY
12. The camera IP will change if modify is successful
13. You can now access the camera settings via Internet Explorer by
typing http://<ip address of camera>
SECTION 2: Accessing the camera using Internet
Explorer WITHOUT IPTool:
6. After saving your temporary settings on the computer, you can now
access the camera using Internet Explorer. In the address bar type:
http://192.168.226.201
**IMPORTANT: AFTER you have configured the camera with a
permanent IP address. You must repeat steps 2-4 and set your
network adapter back to “obtain an IP address automatically.”
If everything has been setup correctly, in both cases you should be
able to access the camera on the local network using Internet Explorer,
or Sibell NVMS
1. connect the IP camera and a Windows computer to a network
switch or router
2. On the computer, browse to:
a. Control Panel\Network and Internet\Network Connections
3. Right-Click Local Area Connection > Choose Properties
4. Highlight Internet Protocol TCP/IP version 4 > Click the Properties
Button
5. See figure 1 Below for temporary IP configuration