Siemens Gigaset M34 USB User manual

M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / cover_front.fm / 27.04.2006
User Manual

2
Contents
M34 fuer USA LBA/ USA EN / A31008-M403-R101-3-7619 / gigaset_manual_m34_eng_v1_0IVZ.fm / 27.04.2006
Contents
Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
For your safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Notes on the operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the software and device drivers . . . . . . . 8
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Gigaset products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Minimum PC requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pack contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Preparing the base station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the Gigaset M34 software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Starting the Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing the device drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Possible problems during installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Checking successful installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Audio settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Registering a base station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Status displays for the Gigaset M34 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Operating information . . . . . . . . . . . . . . . . . . . . . . 17
Operation with multiple devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Configuring the Gigaset M34 software . . . . . . . . . 18
Checking the connection status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Configuring the Gigaset M34 software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Registering a base station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connecting the base station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Changing device names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Calling the Gigaset M34 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Deregistering a base station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Configuring power management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Firmware update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Operating the Gigaset M34 software . . . . . . . . . . 24
Changing and saving settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Opening Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Closing the program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3
Contents
M34 fuer USA LBA/ USA EN / A31008-M403-R101-3-7619 / gigaset_manual_m34_eng_v1_0IVZ.fm / 27.04.2006
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Service (Customer Care) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Guarantee Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Industry Canada Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4
Congratulations
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Congratulations.fm / 27.04.2006
Schablone 2005_07_27
Congratulations
Congratulations on your purchase of the Siemens Gigaset M34 USB Adapter!
Register now!
Register today for the world of Siemens mobile on „gigaset.siemens.com“ and stay current with
customized information on Siemens latest products and applications.
Please go to: http://www.siemenscordless.com/register/
DO NOT RETURN
THIS PRODUCT TO THE
STORE!
Please read the following important information.
For Siemens Customer Care, product operation
information, or for problem resolution, call toll-free
1-888-777-0211
9 a.m. to 8 p.m. Central Standard Time Monday-Saturday
www.siemens.com/gigaset

5
For your safety
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Sicherheitshinweise.fm / 27.04.2006
Schablone 2005_07_27
For your safety
ìBefore installing the Gigaset M34 USB PC adapter and software, carefully read the
following information:
"Notes on the operating instructions" on page 5
"Safety precautions" on page 6
Notes on the operating instructions
Online Help
uDuring installation, detailed descriptions appear on the screen.
uThere is also an online help for each component of the Gigaset M34 software.
Open the appropriate component and then either click on the Help icon in the tool-
bar or press the F1 key.
Operating instructions
You can also print out all the operating instructions, which can be found in *.pdf format
on the CD-ROM supplied. To read the instructions you will need the Adobe Acrobat
Reader program. You can install this directly from the Gigaset M34 software
Setup Wizard.
ìRead the instructions carefully before using for the first time.
Up to date information
The Gigaset M34 CD-ROM also includes the file readme.txt. This contains further
important information that only became available after the manual had been printed.
ìRead the additional information contained in the file readme.txt carefully.
ìAlso note the product information on the Internet at
http://www.siemens.com/gigaset.

6
For your safety
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Sicherheitshinweise.fm / 27.04.2006
Schablone 2005_07_27
Safety precautions
General safety precautions
uOnly give the Gigaset M34 USB to third parties with the installation instructions and
CD-ROM.
uDispose of CD-ROMs you no longer need in an environmentally friendly manner in
line with the statutory requirements.
uNot all of the functions described in this manual are available in all countries.
Installation information
uIn the Windows 2000 and Windows XP operating systems, you must be logged in as
a user with administration rights. Contact your system administrator for details if
necessary.
uBefore installing the Gigaset M34 software, read the information under "System
requirements" on page 8 to avoid loss of data.
uDuring installation, you are prompted to connect the Gigaset M34 USB to a free
USB port on your PC. This starts the Windows operating system's automatic hard-
ware recognition routine and installs the device drivers.
Safety precautions for the Gigaset M34 USB PC adapter
uThe operation of medical appliances may be affected.
uDo not operate the Gigaset M34 USB in bathrooms or shower areas.
The Gigaset M34 USB PC adapter is not splash proof.
uAvoid the immediate proximity of heat sources such as radiators and do not expose
the Gigaset M34 USB to direct sunlight.
uOnly use the USB extension cable supplied.
uDo not connect or disconnect the Gigaset M34 during a storm. This brings a risk of
electric shock.
uIf the Gigaset M34 USB comes into contact with liquid, do not use it.
– Allow the liquid to drain out of the device, and then pat all parts of the device dry.
– Store the Gigaset M34 USB in a warm, dry place for at least 72 hours. In many
cases, you will then be able to use it again.
The radio transmission between the base station and the portable parts is to DECT 6.0
standard. The Gigaset M34 USB PC adapter meets the appropriate US specifications.
Should there nevertheless be any picture and sound interference with satellite receiv-
ers, please consult your retailer to have your satellite receiver equipment tested for poor
shielding.

7
For your safety
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Sicherheitshinweise.fm / 27.04.2006
Schablone 2005_07_27
Trademarks
Windows 2000, Windows XP, Outlook, Windows Media Player and Windows Explorer are
registered trademarks of the Microsoft Corporation.
Acrobat is a registered trademark of Adobe Systems Incorporated.
Yahoo! is a registered trade mark of Yahoo! Communications USA Inc.

8
Installing the software and device drivers
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Installieren.fm / 27.04.2006
Schablone 2005_07_27
Installing the software and device drivers
The Setup Wizard for the Gigaset M34 software guides you through the installation of
all the associated software components.
Normally, the following steps are necessary to successfully install the
Gigaset M34 software:
1. Prepare base station for use, see "Preparing the base station" on page 9.
2. Insert Gigaset M34 CD and run the Setup Wizard, see "Installing the Gigaset M34
software" on page 10.
3. Reboot the PC.
4. Connect the Gigaset M34 USB PC adapter to the PC.
5. Install the device drivers for your Gigaset M34 USB PC adapter.
6. Set up further components as required.
After successful installation, you can start the Gigaset M34 software and configure it to
your own requirements.
System requirements
In order to be able to use the full range of functions, the following minimum require-
ments must be met for installation of the Gigaset M34 USB and software:
Gigaset products
Base station and handset
uA Gigaset S450 or S455base station.
uThe handset that belongs to the base station or a Gigaset S45 handset.
uThe base station is ready for use.
For details, refer to the operating instructions for your base station.
Gigaset M34 USB PC adapter
uThe Gigaset M34 USB should not be connected to the PC before installation.
iDo not plug in the unit until the software has been successfully
installed and when prompted to by the Setup Wizard.

9
Installing the software and device drivers
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Installieren.fm / 27.04.2006
Schablone 2005_07_27
Minimum PC requirements
Hardware
uIBM AT-compatible Pentium III with 500 MHz processor speed
u128 MB RAM main memory
u20 MB free hard disk memory
u1 free USB port
u1CD-ROMdriveor 1 DVD drive
Software
uOperating system
Windows 2000 (Service pack 4) or Windows XP.
Have the installation CD for your Windows operating system to hand. During the
installation of the Gigaset M34 software, the Setup Wizard checks the configuration
of your operating system. You may be prompted to install certain additional
Windows components.
uUser rights
It is necessary that you are logged in as a user with administration rights. Contact
your system administrator for details if necessary.
Pack contents
u1 Gigaset M34 USB PC adapter
u1 USB extension cable
u1 CD-ROM containing software and comprehensive operating instructions
u1 set of installation instructions
Preparing the base station
ìRead the operating instructions for your base station.
ìConnect your base station.
– Connect your base station to your phone line or PABX using the telephone cable.
– Connect the base station to the power supply using the mains adapter.
Your base station is now ready for use.
i
Now that your base station is ready for use, you can make external calls
and also take incoming calls.
It is not necessary to install the Gigaset M34 software to do this.
ìYou can check that your base station is working properly by dialling an
external telephone number.
ìIf you cannot make the call, check your phone line or the settings for
your PABX.
You will find a detailed description in the operating instructions for
your phone line or PABX.

10
Installing the software and device drivers
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Installieren.fm / 27.04.2006
Schablone 2005_07_27
Installing the Gigaset M34 software
ìRead the information in "System requirements" on page 8 and the readme.txt file
before starting to install the Gigaset M34 software. You will find the readme.txt file
in the readme directory on the product CD. It contains current additional informa-
tion on installation and software.
ìClose all the programs running on your PC. This also includes those programs
(e. g. antivirus software), whose activity is only indicated by an icon in the status
area of the taskbar (next to the clock).
Starting the Setup Wizard
ìInsert the Gigaset M34 CD into your PC's CD-ROM drive.
The Setup Wizard for the Gigaset M34 software is started automatically.
The Setup Wizard guides you through the installation.
ìSelect the language in which you want to install the Gigaset M34 software.
ìClick on Next and then on Install software to start the InstallShield Wizard for the
Gigaset M34 software.
iWhen the software has been installed successfully please do not
plug in the device until the Setup Wizard prompts you to do so.
i
If the Setup Wizard for the Gigaset M34 software does not start automat-
ically:
ìOpen Windows Explorer.
ìSelect the CD-ROM drive.
ìDouble click start.exe.

11
Installing the software and device drivers
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Installieren.fm / 27.04.2006
Schablone 2005_07_27
Installing the software
Installation involves various steps in which you can select a number of options. After
each step confirm your selection with Next to continue the installation procedure. Use
Back to return to your previous selection.
This installation wizard guides you through the individual steps of the installation pro-
cedure.
ìClick on Next to start the installation.
The directory in which the software is to be installed is shown.
ìSelect the appropriate mode for installing device drivers. We recommend that you
do not change the Simple (Recommended) settings.
ìClick on Next.
ìSelect the folder where the selected software components are to be installed:
– Click Next to confirm the default installation directory.
Or
– Click Change to choose your own installation directory.
ìClick on Install.
ìAfter installation of the software components, click on Finish to confirm completion
of the installation procedure.
You then need to reboot your PC. You can only set up the Gigaset M34 USB
PC adapter after rebooting.
ìClick on Yes to reboot the PC.
iIf a dialog box appears during installation informing you about a missing
signature, click Yes to continue the installation.

12
Installing the software and device drivers
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Installieren.fm / 27.04.2006
Schablone 2005_07_27
Installing the device drivers
After restarting, installation is continued automatically.
You are prompted to connect the Gigaset M34 USB PC adapter to the PC and the driver
software is then installed. Later, you should register the Gigaset M34 USB PC adapter on
your base station and you can then use the full range of functions of the software.
ìConnect the Gigaset M34 USB to a free USB port on your PC.
ìWhen you connect the Gigaset M34 USB, hardware recognition is started. This
feature monitors the installation of new device drivers. Depending on the previous
configuration of your PC, it may be necessary to install several drivers for you
Gigaset M34 USB PC adapter. Hardware recognition is started automatically for each
driver installation.
– Follow the hardware recognition instructions.
– On Windows XP, confirm the preset options with Next and then click on Finish.
If you cancel hardware recognition, the driver software cannot be correctly
installed.
ìWait until the hardware recognition procedure has completed installation of the
device drivers and you see a message to that effect. Once this message is displayed,
click on Next in the Setup Wizard.
ìClick on Finish in the Setup Wizard.
ìReboot your PC if you are prompted to do so.
ìA message will be displayed, informing you that the standard device settings for
recording and playback have been changed (see also section "Audio settings" on
page 14). Click on OK to complete the installation.

13
Installing the software and device drivers
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Installieren.fm / 27.04.2006
Schablone 2005_07_27
Possible problems during installation
On rare occasions it can happen that a program called up by the Gigaset M34 software
Setup Wizard does not respond:
ìClose the Setup Wizard and the program that is not responding and try again.
If the USB driver cannot be found even though it has been set properly:
ìDisconnect the Gigaset M34 USB PC adapter from your PC.
ìReboot your PC.
ìReconnect the Gigaset M34 USB to your PC.
ìRestart the Setup Wizard.
Checking successful installation
After rebooting the PC, the following things indicate that the Gigaset M34 USB and soft-
ware have been successfully installed:
uThe Start menu contains two new links:
–Start >Programs >Gigaset DECT >Gigaset M34 Software
–Start >Programs >Gigaset DECT >Gigaset M34 USB – Firmware update
uThe following items have been added to the Device Manager in your Windows
operating system (Start >Settings >Control Panel >System >Hardware >Device
Manager):
–UnderDECT Devices:Cordless Internet Access
–UnderAudio, Video and Game Controllers: USB Audio Device
–UnderUniversal Serial Bus Controllers: Cordless Device Configuration,
Cordless Device Line Access, Cordless Device Update, Cordless PC Control
uThe Software area in the Control Panel of the Windows operating system shows
the names of the installed software components:
–Gigaset M34 Software
i
uIf you want to use your Gigaset M34 USB PC adapter for Internet tele-
phony (VoIP), you must install Yahoo! Messenger with Voice on your
PC. The software is available on the Internet at
http://messenger.Yahoo.com. Reboot your PC after installation.
u
!
In some older PC systems, chipsets are fitted, which no longer correspond
to the valid USB standard. This can lead to problems with the USB connec-
tion.
Manufacturers of these hardware components normally supply a driver
update. Please contact the manufacturer of your PC.

14
Installing the software and device drivers
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Installieren.fm / 27.04.2006
Schablone 2005_07_27
–Gigaset M34 USB
Audio settings
Due to Microsoft Software Regulations the audio device driver USB Audio Device has
been installed onto your PC as your default device for recording and playback. This is
also necessary because it allows you to listen to music through your handset with
Windows Media Player or make phone calls via the Internet.
For example, if you wish to record or playback sound on your PC (e.g. through your PC's
loudspeaker/microphone or connected headphones) while playing a computer game,
you must change the settings of the device driver.
ìClick on Start > Settings > Control Panel > Sounds and Multimedia
(Windows 2000) or Sounds and Audio Devices (Windows XP), Audio tab.
ìFor sound playback and recording, select the default sound card driver of your PC as
the default device instead of the entry USB Audio Device
(List: Preferred Device/Default Device).
ìClick on OK to accept the setting.
Using PC loudspeaker/headset with your handset
In most Windows applications you can also give the audio device driver specific settings
irrespective of the settings in the Control Panel. This allows you to specify where sound
is recorded and played back (PC or handset) for specific applications.
For example, if you have set your PC's default soundcard driver, you can make a phone
call with your handset over the Internet while listening to music through your PC's loud-
speakers at the same time.
Please note: For Internet telephony with Yahoo! Messenger with Voice, the device
driver USB Audio Device is automatically set (temporarily) as soon as you telephone
with the handset.
i
uCertain entries are only displayed when a base station is connected.
uThe drivers may have different names depending on the Windows
operating system you are using and the voice packets installed.

15
Installing the software and device drivers
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Installieren.fm / 27.04.2006
Schablone 2005_07_27
Registering a base station
You can register your Gigaset M34 USB on up to 6 base stations. The registered base sta-
tions are saved in the software and you can then connect to one of the registered base
stations as required.
ìOpen the Gigaset M34 software via Start > Programs > Gigaset DECT > Gigaset
M34 Software.
ìIn the menu tree, select the M34 USB > Configuration entry.
ìUnder Base stations click on one of the <free base> options.
The Register button is activated.
ìSet the base station to registration mode.
– Press and hold the registration key for approx. 3 seconds (on the S455, hold until
you hear an acoustic signal).
– Refer to the operating instructions for your base station for more details.
ìClick on Register to begin registration.
This opens the Register dialog.
ìEnter the PIN for the base station (factory default "0000") and confirm your entry
with OK.
ìWait until registration has been completed.
The Register dialog is closed.
Once the connection between your base station and the M34 USB has been estab-
lished, you will see the base station data on your PC. The Name: field contains the
name under which the Gigaset M34 USB has been registered on the base station.
You will need this name to establish the connection between the handset and the
M34 USB.
i
Requirements:
uThere must be a free space in the list under Base stations.
uThere must be another free registration location for internal
subscribers on the base station.
uThe base station must be in registration mode before commencing
the registration procedure.
uThe base station PIN must be entered during registration.
For further information, refer to the operating instructions for the rele-
vant base station.

16
Installing the software and device drivers
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Installieren.fm / 27.04.2006
Schablone 2005_07_27
Status displays for the Gigaset M34 USB
LED is constantly illuminated: Base station found; Gigaset M34 USB is ready for use.
LED flashes slowly: Gigaset M34 USB is looking for the base station or no base station
has been registered.
LED flashes quickly: Data connection active between Gigaset M34 USB and base
station.
LED flickers: Gigaset M34 USB is in firmware update mode.

17
Operating information
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / HinweiseBetrieb.fm / 27.04.2006
Schablone 2005_07_27
Operating information
Your Gigaset M34 USB PC Adapter opens up a wide range of possibilities when used in
conjunction with your Gigaset base station and the Gigaset M34 software.
The Gigaset M34 USB is a PC adapter, which allows wireless communication between
your Gigaset base station and your PC. For example, you can transfer your PC directories
to the handset, make calls over the Internet or operate the PC remotely from the hand-
set.
You can use the Gigaset M34 software to configure the connection between your base
station and your PC. The software does not have to be started to use the basic functions
of your Gigaset M34 USB PC adapter; you only need the software for special functions
such as transferring directories.
Operation with multiple devices
You can register your Gigaset M34 USB PC adapter to up to 6 Gigaset base stations of
type S450 and S455. It is a precondition that there is a free registration location for
handsets on the base station.

18
Configuring the Gigaset M34 software
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Konfigurieren.fm / 27.04.2006
Schablone 2005_07_27
Configuring the Gigaset M34 software
With the Gigaset M34 USB, you can set up your PC for operation on up to 6 base stations.
Particularly when the location of the PC or laptop changes often, this provides the
advantage that you only need to enter the available base stations once in the configu-
ration to be able to establish a connection from those locations at any time. However,
you should note that a simultaneous connection to multiple base stations is not possi-
ble.
Use the M34 USB option in the menu tree to open up the configuration of the Gigaset
M34 software. The following configuration dialogs are available:
Checking the connection status
ìOpen the Gigaset M34 software and select the M34 USB > Status option in the
menu tree.
The working area displays up to date information about the connection to the base
station:
Connected base:
If a connection already exists, the name of the base station to which your PC is con-
nected via the Gigaset M34 USB is shown.
Field strength:
The signal strength of the wireless connection is indicated in the form of a bar.
Connection status:
The wireless connection can have the following operating statuses:
–Initialise
Connecting; searching for an available base station.
–No connection
No connection to base station or connection broken.
–Active
Your PC is connected to the base station displayed.
Menu tree Brief description
M34 USB
Status Display connected base station and quality of connec-
tion
Configuration Register and configure Gigaset M34 USB
Firmware update Update device software for your Gigaset M34 USB

19
Configuring the Gigaset M34 software
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Konfigurieren.fm / 27.04.2006
Schablone 2005_07_27
Configuring the Gigaset M34 software
You can make various settings in the Gigaset M34 software: change the names of your
devices, register or deregister base stations, connect devices to one another, control the
power management feature and update the firmware if necessary
Registering a base station
ìOpen the Gigaset M34 software and select the M34 USB > Configuration option in
the menu tree.
ìUnder Base stations click on one of the <free base> options.
The Register button is activated.
ìSet the base station to registration mode.
– Hold down the Registration key for a few seconds. Some base stations indicates
registration mode with an acoustic signal or a flashing LED.
– Refer to the operating instructions for your base station for more details.
ìClick on Register to begin registration.
This opens the Register dialog.
ìEnter the PIN for the base station (factory default "0000") and confirm your entry
with OK.
ìWait until registration has been completed.
The Register dialog is closed.
ìFor further information refer to "Registering a base station" on page 15.
Connecting the base station
When you register a base station, it is connected immediately. If several base stations
are registered, you can choose which one to connect to. The base stations that are not
connected do not need to be deregistered. This allows you to switch between different
base stations without having to set them to registration mode again.
ìOpen the Gigaset M34 software and select the M34 USB > Configuration option in
the menu tree.
ìUnder Base stations click on one of the base stations that is registered but not con-
nected.
The Connect button is activated.
ìClick on the base station you want to connect.
ìClick on Connect.

20
Configuring the Gigaset M34 software
M34 fuer USA LBA / USA EN / A31008-M403-R101-3-7619 / Konfigurieren.fm / 27.04.2006
Schablone 2005_07_27
Changing device names
When connected to a base station, your PC is uniquely identifiable by its device name.
You can change this device name as required. It is a precondition that your Gigaset M34
USB is connected to the base station.
ìOpen the Gigaset M34 software and select the M34 USB > Configuration option in
the menu tree.
The working area shows the current device name of the Gigaset M34 USB.
ìEnter the desired device name under Identification > Name:. The maximum length
of the device name is 10 characters.
ìConfirm your entry by pressing the return key (Return, Enter).
The new device name is sent to the connected base station.
Calling the Gigaset M34 USB
A connection between your handset and the Gigaset M34 USB allows you to access the
PC through your handset. The requirement for this connection is that your handset is
registered on the same base station as the Gigaset M34 USB. To create the connection
between your handset and the Gigaset M34 USB, make a free internal call from the
handset to the Gigaset M34 USB.
ìPress the INT key on your handset.
ìChoose the Gigaset M34 USB as the internal party. The internal name under which
it is registered on the base station can be seen in the Gigaset M34 software under
M34 USB > Configuration >Name:.
ìPress the Talk or Handsfree key on the handset to make the internal connection.
iIf you also want to change the device name of your PC for connections to
another registered base station, first of all connect to the desired base
station and then repeat this procedure.
!Note that your handset will be blocked to other calls for the duration of
the internal connection.