Siemens XLS-MSE3-ADPT User manual

Installation Instructions
Model XLS-MSE3(R)-ADPT
Adapter Kit
SiemensSiemens
SiemensSiemens
Siemens IndustryIndustry
IndustryIndustry
Industry,,
,,
,Inc.Inc.
Inc.Inc.
Inc.
BuildingBuilding
BuildingBuilding
Building
TT
TT
Tecec
ecec
echnologies Dihnologies Di
hnologies Dihnologies Di
hnologies Divisionvision
visionvision
vision
A6V10328636_en--_c
INTRODUCTION Use the Model XLS-MSE3(R)-ADPT Adapter Kit from Siemens Industry, Inc., to
upgrade existing MXL-IQ Systems installed in Model MSE-3L(R) or MSE-3M(R)
backboxes to FireFinder-XLS/Desigo Fire Safety Modular/Cerberus PRO Modular
Systems.The MSE-3L(R) and MSE-3M(R) will be referred to as MSE-3(R) in the
remainder of the document.
The XLS-MSE3(R)-ADPT Adapter Kit consists of an adapter plate, inner door and outer
door. The XLS-MSE3-ADPT (S54430-C14-A1) inner and outer doors are black; the
XLS-MSE3R-ADPT (S54430-C14-A2) inner door is black and outer door is red.The
XLS-MSE3-ADPT and the XLS-MSE3R-ADPT are identical in all other ways and will be
referred to in the remainder of this document as XLS-MSE3-ADPT.
The adapter plate installs over the existing studs in an MSE-3(R) backbox. The inner
door has an opening in it for the installation of a FCM2041-U2/-U3 operator interface
and either one ID-MP mounting plate or one ID-SP blank plate. The inner door is
permanently hinged right and is attached to the backbox by screws.
The XLS-MSE3(R)-ADPT is for indoor use only in dry environments.
With this conversion, the maximum battery set that can be used in the backbox is 18
AH (model BP-61). If larger batteries are required, use either a BB-55 or CAB-BATT
battery box.
To convert an MSE-3(R) backbox from an MXL-IQ System to an XLS/Desigo Fire
Safety Modular/Cerberus PRO Modular component system, you must first disas-
semble the MXL-IQ and then assemble the XLS/Desigo Fire Safety Modular/Cerberus
PRO Modular. This two-part procedure is described in detail below.
DISASSEMBLY OF MXL-IQ SYSTEM
Remove all system power, first battery and then AC.
1. Remove and discard the outer door. Reserve the hardware used to secure it
in place.
2. Disconnect and remove the modules from the inner door.
3. Remove all modules from the backbox, making sure to mark all wires.
Reserve the hardware used to secure them in place.
4. Remove the MPS power supply and batteries from the backbox.

Siemens Industry, Inc.
Building Technologies Division
A6V10328636_en--_c2
ASSEMBLY OF XLS/DESIGO FIRE SAFETY MODULAR/CERBERUS PRO SYSTEM
The three parts of the XLS-MSE3-ADPT are installed separately.The adapter plate is
installed first, followed by the inner door and then the outer door.
Adapter Plate The XLS-MSE3-ADPT adapter plate has holes in it that fit over the studs in the MSE-3
backbox in only one way.
1. Place the XLS-MSE3-ADPT over the studs in the backbox and secure it in
place with the hardware provided as shown in Figure 1.
MSE-3
BACKBOX
XLS-MSE3(R)-ADPT
ADAPTER PLATE
“B”
“C” “C”
“A” “A”=6-32X
“B” =10-32 X 7/16 SCREWS (QTY. 2)
“C” = 6-32 HEX NUTS (QTY. 2)
3/8 SCREWS (QTY. 5)
“A” “A”
“B”
“D”
GROUND LUG
(THIS LUG IS FOR GROUNDING
THE AC INPUT)
REMOVE GROUND LUG BEFORE
MOUNTING THE PTB.
AFTER INSTALLING THE PTB, BE SURE
TO REINSTALL THE GROUND LUG.
Figure 1
Installing the XLS-MSE3-ADPT Adapter Plate in the MSE-3 Backbox
2. Install the required CC-5 system cardcage, PSC-12 power supply, and PTB
power termination board after careful consideration of NEC Article 760 for
separation of power limited and non-powered limited wiring. Refer to Figure
2. Use the hardware provided with those modules to mount them to the
adapter plate. Refer to the CC-5 Installation Instructions, P/N 315-033035,
and the PSC-12 Installation Instructions.
3. One PTB can be mounted on the XLS-MSE3-ADPT on the bottom right of
the plate using the four studs provided. Refer to the PTB Installation
Instructions, P/N 315-034877. The stud marked “D” in Figure 1 is a lug for
grounding the AC input. Remove the ground lug before mounting the PTB.
After installing the PTB, be sure to reinstall the ground lug.
4. A battery set of up to 18 AH capacity can be placed in the bottom of the
enclosure.
5. System cards can be installed in the CC-5 cardcage, as required.

Siemens Industry, Inc.
Building Technologies Division
A6V10328636_en--_c3
MSE-3
BACKBOX
PSC-12
PTB
BATTERIES
CC-5
Figure 2
Mounting the XLS/Desigo Fire Safety Modular/Cerberus PRO Modular Modules in the MSE-3 Backbox
Install the Inner Door Install the inner door by following the steps listed below.
1. Place two of the four #6-32x5/16 screws provided in the top and bottom
holes on the right-hand side of the backbox.
2. Tighten the screws just a few turns leaving a 1/8-inch gap between the
head of the screws and the backbox.
3. Slide the inner door into position under the screws.
4. Make certain the flange at the left-hand top of the inner door is seated in
the lip in the backbox. (Refer to Figure 3.) Adjust the door as needed so that
it seats securely in the enclosure.
INNER
DOOR
MSE-3
BACKBOX
LIP OF
DOOR
FLANGE
8-32x5/16
SCREWS
(QTY. 4)
LOCATION
OF OPTIONAL
HTSW-1 TAMPER
SWITCH
Figure 3
Installing the Inner Door

Siemens Industry, Inc.
Building Technologies Division
A6V10328636_en--_c4
5. Insert the remaining two screws in the two holes on the right side of the
backbox to secure the inner door.Tighten all four of the screws.
6. Install a FCM2041-U2/-U3 on the inner door. Refer to the PMI Installation
Instructions, P/N 315-033070, the FCM2041-U2 Installation Instructions,
Document ID A6V11231623, or the FCM2041-U3 Installation Instructions,
Document ID A6V11231630, for further information.
7. Install door-mounted modules (FCM-6, LCM-8, SCM-8) as needed for
system operation.
8. Insert blank plates, as needed, in unused space on door and secure with
#10-32 nuts. (Refer to Table 1 and Figure 4.)
1ELBAT
SETALPROODRENNI
LEDOMNOITPIRCSEDGNITNUOM
PM-DI,6-MCFroftekcarb/etalpgnitnuoM
.MCBdna8-MCS,8-MCL
deruce
S.roodnisdutsnostnuoM
.stun23-01owthtiw
PS-DIehtsaezisemasehttresniknalB
.tekcarb/etalpgnitnuomPM-DI
deruc
eS.roodnisdutsnostnuoM
.stun23-01owthtiw
XLS-MSE3-ADPT
INNERDOOR
ID-
S
P
O
R ID-MP
MOUNTING
FCM2041-U2/-U3
MOUNTING
Figure 4
Inner Door Modules
Install the Outer Door The outer door is shipped with a clear lens installed in the door opening.
1. Insert the hinge pins on the outer door in the hinges on the backbox.
2. Place the XLS system label, P/N 575-234411, Desigo Fire Safety Modular
sytem label, P/N A5Q00075144, or Cerberus PRO Modular system label, P/
N A5Q00075194, on the inside of the outer door.
3. A ground wire comes installed on the inside of the outer door. (Refer to
Figure 5.) Bring the free end of the ground wire through the opening at the
top left-hand side of the inner door and secure it in place on an unused stud
in the backbox with a #10-32 hex nut (user supplied).
4. Close the outer door and secure with the key latch.

Siemens Industry, Inc.
Building Technologies Division
A6V10328636_en--_c5
MSE-3 BACKBOX
OUTER DOOR
GROUND WIRE
WIRE: 12AWG
UNUSED STUD
Figure 5
Ground Wire Installation
WIRING In compliance with NEC Article 760, all power limited fire protective signaling
conductors must be separated a minimum of ¼ inch from all of the following wiring
located within a control panel:
• electric light
•power
• Class 1 or non-power limited fire protective signaling conductors
To meet these requirements, the following guidelines must be observed when
installing modules and wiring to this control panel.
When installing power limited field wiring, the installer must comply with NEC article
760, which states:
The fire alarm power-limited circuits are installed using Types FPL, FPLR, FPLP or
permitted substitute cable, provided these power-limited cable conductors extending
beyond the jacket are separated by a minimum of 0.25 in. (6.35 mm) or by a noncon-
ductive sleeve or nonconductive barrier from all other conductors.
If energy limited cable or equivalent is not used within the enclosure, then the following
guidelines do not apply. In that case,be sure to follow standard wiring practices.
Wiring Entering Enclosure Non-Power Limited Wiring
Wiring entering the enclosure from the bottom and right side of the backbox is
considered non-power limited wiring. Wiring must be in the shortest route and must
not overlap any other wiring.

Siemens Industry, Inc.
Building Technologies Division
A6V10328636_en--_c6
Power Limited Wiring
Wiring entering the enclosure from the top and the left side of the backbox is
considered power limited. Wiring must be in the shortest route and must not overlap
any other wiring.
Use the existing lances in the backbox to dress the wires as needed to maintain
separation of power limited and non-power limited wiring.
Use the existing lances on the adapter plate to dress the wires as needed to main-
tain separation of power limited and non-power limited wiring.
Install Wiring The primary mains input must have a separate or dedicated circuit breaker. Wire in
accordance with local codes and Article 760 of NEC.
1. Remove the knockouts in the backbox for the entry of field wiring.
2. Pull all field wiring into the backbox. Do not dress the wiring until the
location of all the equipment is known.
3. Install the wiring from the external power source to the approximate
location of the power supply.

Siemens Industry, Inc.
Building Technologies Division
A6V10328636_en--_c7
Cyber security disclaimer
Siemens products and solutions provide security functions to ensure the secure operation of building comfort,
fire safety, security management and physical security systems. The security functions on these products and
solutions are important components of a comprehensive security concept.
It is, however, necessary to implement and maintain a comprehensive, state-of-the-art security concept that is
customized to individual security needs. Such a security concept may result in additional site-specific preventive
action to ensure that the building comfort, fire safety, security management or physical security system for your
site are operated in a secure manner. These measures may include, but are not limited to, separating networks,
physically protecting system components, user awareness programs, defense in depth, etc.
For additional information on building technology security and our offerings, contact your Siemens sales or
project department. We strongly recommend customers to follow our security advisories, which provide infor-
mation on the latest security threats, patches and other mitigation measures.
http://www.siemens.com/cert/en/cert-security-advisories.htm

Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Canada, Ltd.
1577 North Service Road East
Oakville, Ontario
L6H 0H6 Canada
Document ID A6V10328636_en--_cP/N A5Q00054384