Siemens ACC AP User manual

Access Control
SiPass integrated
ACC AP Technical Manual
MP 2.80
A6V11367717
Smart Infrastructure
07.09.2020

Copyright
2 | 16
A6V11367717
Copyright
Technical specifications and availability subject to change without notice.
We reserve all rights in this document and in the subject thereof. By acceptance of
the document the recipient acknowledges these rights and undertakes not to
publish the document nor the subject thereof in full or in part, nor to make them
available to any third party without our prior express written authorization, nor to
use it for any purpose other than for which it was delivered to him.
Edition: 07.09.2020
Document ID: A6V11367717
© Siemens Switzerland Ltd, 2020

A6V11367717
3 | 16
Table of Contents
1 About this Document .................................................................................. 5
2 Details for Ordering..................................................................................... 6
3 Safety Regulations...................................................................................... 7
4 Standards and Guidelines........................................................................... 8
5 Technical Specifications ............................................................................. 9
5.1 Battery ...........................................................................................................10
5.2 ACC-AP Controller Diagram .........................................................................10
5.2.1 Description of Numbered Items in the Diagram.............................11
6 Installation ................................................................................................ 12
6.1 OSDP Reader Connections ..........................................................................12
6.2 Wiegand Reader Connections ......................................................................12
6.3 Mounting........................................................................................................14
6.4 Tamper Function ...........................................................................................15
6.5 Configuration .................................................................................................15

About this Document
1
A6V11367717
5 | 16
1About this Document
This document contains information on the mounting and installation of the
product.
The ACC-AP, SiPass Firmware and Aperio Wireless Locks (which can be
configured only on ACC-AP) work in relation to each other. Hence, it is
recommended that the following documents (from SiPass integrated Software
bundle) are read in conjunction:
●ACC-AP Technical Manual (this document)
●SiPass integrated Firmware Configuration Guide
●SiPass integrated Configuration Client User Guide
●Aperio Wireless Lock Support Guide

Details for Ordering
2
6 | 16
A6V11367717
2Details for Ordering
The ACC-AP IP Door Controller can be ordered as a Standalone unit or as ACC-
APM PSU unit in 12V/24V voltage options.
Part Number
Type
Description
S54502-C150-A100
ACC-AP
ACC-AP SiPass integrated IP Door Controller
S54502-C152-A100
ACC-APM-1220
ACC-APM-1220 SiPass IP Controller
12V 2A PSU
S54502-C153-A100
ACC-APM-2420
ACC-APM-2420 SiPass IP Controller
24V 2A PSU

Safety Regulations
3
A6V11367717
7 | 16
3Safety Regulations
General
●Follow all warnings and instructions marked on the device.
●Keep this document for reference purposes.
●Please take into account any additional country-specific local laws, safety
standards or regulations concerning installation, operation and disposal of the
product.
●Refer to a qualified electrician for installation.
Liability claim
●Do not make any changes or modifications to the device.
●Use only spare parts and accessories that have been approved by the
manufacturer.

Standards and Guidelines
4
8 | 16
A6V11367717
4Standards and Guidelines
Siemens Switzerland Ltd. hereby declares that this product is in compliance with
the essential requirements and other relevant provisions of:
●Directive 2011/65/EU (Restriction of the use of certain hazardous substances
directive)
●Directive 2014/30/EU (Electromagnetic Compatibility directive)
●Directive 2014/35/EU (Low Voltage directive)
The EC Declaration of Conformity is available from your local Siemens sales office
or from the address below:
Siemens Switzerland Ltd
Building Technologies Division
Theilerstrasse 1a, CH-6300 Zug
[phone]

Technical Specifications
Battery
5
A6V11367717
9 | 16
5Technical Specifications
The technical data for the ACC-AP is as below:
Default IP Address
192.168.251.1
Subnet mask:
255.255.255.0
Supply voltage (nom.*)
12-24 Vnom +/- 10% 1Vpp ripple
Absolute voltage ratings**
9.5V DC –29.5V DC
The AP power supply input must be
protected by a fuse (2A).
Current consumption
Without reader
Idle
12V DC: 200mA
24V DC: 140 mA
Full on***
12V DC: 600mA
24V DC: 400 mA
Battery Type
CR2032
Reader Interface
An electronic fuse blows when the total
current to both the reader interfaces
exceeds 700mA.
Two OSDP Readers plus Power out.
Two Wiegand Readers plus Power out.
Max 700mA (jumper in Vin position)
Max 200mA (jumper in 12V position)
Inputs
Four general inputs
Outputs
Two relay outputs. Max 30V DC, 2A. One
bistable, one monostable.
Four Open-collector outputs, max load 0.5A.
One power supply output with Vin, max load
2A.
Resistor Value for Monitored Inputs
22k (alarm)
11k normal
Temperature Range
-40 to +55 0C
Humidity
250C @80% -> 550C @93%
(III, IEC 60839-11-1)
Environmental Class
II, IEC 60839-11-1
Dimensions (H x W x D)
156 x 201 x 53 mm
* Nominal voltage has margins for transformer tolerances, mains supply variations and
interruptions
** Absolute voltage has no margins and should be used for guidance only
*** Full on represents:
●500 mA (5V) load on high-speed USB connector
●100 mA (5V) load on full-speed USB connector
●No readers connected
●Relays activated
●RJ485 communication on all ports with EOL resistors
●Micro-SD memory card installed

Technical Specifications
Battery
5
10 | 16
A6V11367717
5.1 Battery
The “CR2032” battery type is supplied and should be mounted in the battery socket
(see item 13 in the AP Controller Diagram ) with the plus (+) mounted downwards.
The battery keeps the Audit Trail data intact for about 30 days during any power
fail.
5.2 ACC-AP Controller Diagram
See section Description of Numbered Items in the Diagram [➙ 10] for detailed
information.