Siemens SIMATIC NET TeleControl SINAUT ST7 User guide

___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC NET
Industrial Remote Communication -
TeleControl
SINAUT ST7 station control system
System Manual
Volume 1: System and Hardware
09/2016
C79000
-G8976-C178-10
Preface
Properties of the SINAUT
components
1
Network structures and
topologies
2
Installation guide
3
Installing and putting a TIM
into operation
4
Installation and
commissioning of the
modems and routers
5
Technical specifications
6
Certifications and approvals
7
References
A

Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C178-10
Ⓟ
10/2016 Subject to change
Copyright © Siemens AG 2009 - 2016.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance a
re required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10 3
Preface
Note
Discontinuation of modules
As of 01.10.2016 the following products have the status "discontinued":
•
Modem MD2
•
Modem MD3
•
LTOP1 / LTOP2
•
Accessories:
Overvoltage protection module as replacement part for LTOP1 and LTOP2, DIN rail
adapter, various plug-in cables
Observe the product notifications on the Internet:
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15915/pm)
•
EGPRS router MD741-1
Observe the following product notification:
Link: (https://support.industry.siemens.com/cs/ww/en/view/62607452)
If there are successors to the discontinued devices, you will find these in the notifications
listed above on the Internet.
What's new in SINAUT ST7?
SINAUT ST7 provides the following new functions:
●
Engineering software
New version of the SINAUT ST7 configuration and diagnostics software V5.5 SP2
After release of the version V5.4 of the engineering software small functional
improvements were made. In addition to this, the following functions are new:
–Configuration of a proxy TIM 3V-IE Advanced as substitute for a CP 1243-8 IRC
The 1243-8 IRC can be configured in STEP 7 Basic as of version V13.0 SP1.
You will find the description in Volume 2 in section 3.2, PROXY CP1243-8 IRC.
–Improvement of the selective connection configuration by selecting individual
subscribers
–Passing of the key exchange interval to the MODEM MD720 when using the MSC
protocol
–Errors corrected in the time-of-day synchronization of a TIM by the CPU
You will find the description in Volume 2 in section 3.5, Synchronization of an Ethernet
TIM by the CPU.

Preface
SINAUT ST7 station control system
4System Manual, 09/2016, C79000-G8976-C178-10
To upgrade to this version, a full version of the SINAUT engineering software V5.0 must
be installed.
The engineering software V5.5 SP2 can be used with STEP 7 as of version V5.4 SP4.
To use the engineering software, a Windows operating system is required that is
compatible with the installed STEP 7 version.
You will find details on the ordering data and operating systems of the engineering
software in volume 2 of the system manual in the section SINAUT ST7 software: Ordering
data and compatible operating systems.
●
Block library TD7onCPU
New version of the block library TD7onCPU V2.2 SP4 + Hotfix 1
–New block "FC-PathStatus" to display the main and substitute path to the remote
communications partner.
The block can be used as of version V5.5 SP1 of the engineering software and as of
TIM firmware V2.5.4.
–The block library can now be used both in a standalone TIM in an S7-400 and an S7-
400H also with only one single CPU (single mode).
●
TIM firmware
The new functions of the SINAUT engineering software named above are supported by
firmware version V2.5.4 for the following TIM modules:
TIM 3V-IE, TIM 3V-IE Advanced, TIM 4R-IE
Replaced documentation
This manual replaces the manual release 08/2011 (C79000-G89xx-C222-07).
For older releases of the manual, see below, section Version history (Page 7).
Purpose of the manual
The SINAUT ST7 system manual is split into two complementary volumes.
●
Volume 1: System & Hardware
This documentation will support you on your way to successful application of SINAUT
ST7. This introduces you to the topic in clear and straightforward steps and provides you
with an overview of the hardware components of the SINAUT ST7 station control system.
You will be supported during the planning of network structures and topologies and will
see how to install and commission SINAUT components based on the installation
guidelines.
●
Volume 2: Software
This documentation provides you with an overview of the software components of the
SINAUT ST7 station control system. You will see how individual components are
configured. Diagnostics and service options are also explained.

Preface
SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10 5
Note
Documentation for the SINAUT ST1 system and older modules
This release of the
manual "SINAUT ST7" (volume 1 + 2) no longer has detailed information
on the SINAUT
ST1 system and the following older modules:
•
All previous TIM 3 modules: TIM 3V, TIM 32, TIM 33, TIM 34
•
TIM 4V, TIM 4VD, TIM 42, TIM 42D, TIM 43, TIM 43D, TIM 44, TIM 44D
If
you require information on these modules or on SINAUT ST1, refer to release 05/2007 of
this manual. You will find release 05/2007 on the Internet pages of Siemens Industry Online
Support at the following address:
Link: (
https://support.industry.siemens.com/cs/ww/en/ps/15931/man)
The documents have the following IDs.
•
Volume 1: 24621696
•
Volume 2: 24619519
Validity of this manual
This manual applies to the following ST7 modules and software versions:
●TIM 3V-IE, TIM 3V-IE Advanced, TIM 4R-IE, TIM 4R / 4RD
●SINAUT ST7 configuration and diagnostics software for the PG V5.4
●SINAUT TD7 library for the CPU V2.2 SP2
●SINAUT TIM firmware V4.4.0 for the TIM 4
●SINAUT TIM firmware V2.5 for the TIM 3V-IE variants
●SINAUT TIM firmware V2.5 for the TIM 4R-IE
Further information on the Internet
You will find further information on the TeleControl ST7 products on the Internet at the
following address:
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15931/man)
There select the required information under "Entry type" (for example "Updates", "Manuals",
"FAQs" etc.).
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions only form one element of such a concept.

Preface
SINAUT ST7 station control system
6System Manual, 09/2016, C79000-G8976-C178-10
Customer is responsible to prevent unauthorized access to its plants, systems, machines
and networks. Systems, machines and components should only be connected to the
enterprise network or the internet if and to the extent necessary and with appropriate security
measures (e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit
Link: (http://www.siemens.com/industrialsecurity)
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends to apply product updates as soon as available and to
always use the latest product versions. Use of product versions that are no longer supported,
and failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
Link: (http://www.siemens.com/industrialsecurity).
License conditions
Note
Open source software
Read the license conditions for open source software carefully before using the product.
You will find license conditions in the following documents on the supplied data medium:
●OSS_TIM-ST7_86.pdf
●OSS_SINAUT-ES_86.pdf
SIMATIC NET glossary
Explanations of many of the specialist terms used in this documentation can be found in the
SIMATIC NET glossary.
You will find the SIMATIC NET glossary here:
●SIMATIC NET Manual Collection or product DVD
The DVD ships with certain SIMATIC NET products.
●On the Internet under the following address:
Link: (https://support.industry.siemens.com/cs/ww/en/view/50305045)
Training, Service & Support
You will find information on training, service and support in the multilanguage document
"DC_support_99.pdf" on the Internet pages of Siemens Industry Online Support:
Link: (https://support.industry.siemens.com/cs/ww/en/view/38652101)

Preface
SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10 7
Trademarks
The following and possibly other names not identified by the registered trademark sign ®are
registered trademarks of Siemens AG:
SINAUT, TIM, SCALANCE, MODEM MD720, MD741-1, Modem MD2 / MD3 / MD4, LTOP
Version history
The previous versions of the manual described the innovations and versions listed below.
Release 09/2014 of the manual (C79000-G89xx-C222-09)
New functions:
●New version of the SINAUT ST7 configuration and diagnostics software V5.4
–Time-of-day synchronization of the TIM 4R-IE using NTP
You will find the description in Volume 2 in section 3 (Configuration in STEP 7 >
Configuration of TIM modules > "NTP" tab).
–Synchronization of the TIM time of day by the CPU
You will find the description in Volume 2 in the section 3 (Configuration in STEP 7 >
Configuration of the time-of-day synchronization).
–MSCsec protocol: Secure transfer, authentication with key exchange
You will find the description in Volume 2 in section 2 (Configuration - Overview >
GPRS/Internet Communication).
●New firmware version V2.5 for the TIM modules TIM 3V-IE, TIM 3V-IE Advanced,
TIM 4R-IE
The functions named above among the innovations of the configuration software are new.
Validity of the manual:
●TIM 3V-IE, TIM 3V-IE Advanced, TIM 4R-IE, TIM 4R / 4RD
●SINAUT ST7 configuration and diagnostics software for the PG V5.4
●SINAUT TD7 library for the CPU V2.2 SP2
●SINAUT TIM firmware V4.4.0 for the TIM 4
●SINAUT TIM firmware V2.5 for the TIM 3V-IE variants
●SINAUT TIM firmware V2.5 for the TIM 4R-IE
Release 08/2011 of the manual (C79000-G89xx-C222-08)
New functions:
●New version of "SINAUT ST7 configuration and diagnostics software" V5.2
●Version "SINAUT ST7 configuration and diagnostics software" V5.1
●New SINAUT TD7 library V2.2 SP2 for the CPU

Preface
SINAUT ST7 station control system
8System Manual, 09/2016, C79000-G8976-C178-10
Validity of the manual:
●SINAUT ST7 configuration and diagnostics software for the PG V5.2
●SINAUT TD7 library for the CPU V2.2 SP2
●SINAUT TIM firmware V4.4.0 for the TIM 4
●SINAUT TIM firmware V2.3 for the TIM 3V-IE variants
●SINAUT TIM firmware V2.3 for the TIM 4R-IE
Release 07/2009 of the manual (C79000-G89xx-C222-07)
New functions:
●New version "SINAUT ST7 configuration software for the PG/PC" V5.0
–The Ethernet TIMs can be configured for communication via the MSC protocol. This
allows the use of the GPRS/GSM modem SINAUT MD720-3 even in SINAUT in
Internet/GPRS networks. An encrypted connection can be established from an
Ethernet TIM to the Internet via a DSL modem.
–The time slot method can now also be configured with the "SINAUT ST7 configuration
software for the PG/PC" as of V5.0 for a master TIM without DCF7 receiver, if a
TIM 4R-IE with an Ethernet connection to an ST7cc/ST7sc PC is used as the master
TIM.
The configuration software Version V5.0 can be used with STEP 7 as of Version V5.4
Service Pack 4.
The configuration software version V5.0 is supported by the following operating systems:
–Windows XP Professional SP2
–Windows Server 2003 SP2
–Windows Vista 32 Bit Ultimate and Business (with or without SP1)
●New firmware version V2.0 for all Ethernet TIM modules
The new firmware supports the MSC protocol.
Validity of the manual:
●SINAUT ST7 configuration software for the PG/PC V5.0
●SINAUT TD7 library for the CPU V2.2
●SINAUT TIM firmware V4.3.9 for the TIM 4
●SINAUT TIM firmware V2.0 for the TIM 3V-IE variants
●SINAUT TIM firmware V2.0 for the TIM 4R-IE
Release 05/2007 of the manual (C79000-G89xx-C222-06)
New functions:
●New product "TIM 4R-IE" for connecting SINAUT via WAN and Ethernet
●New product version "SINAUT ST7 configuration software for the PG/PC" V4.1

Preface
SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10 9
Validity of the manual:
●SINAUT ST7 configuration software for the PG/PC V4.1
●SINAUT TD7 library for the CPU V2.2
●SINAUT TIM firmware V4.3.7 for the TIM 3 / TIM 4
●SINAUT TIM firmware V1.2 for the TIM 3V-IE variants
●SINAUT TIM firmware V1.0 for the TIM 4R-IE
Release 10/2006 of the manual (C79000-G89xx-C222-05)
New functions:
●New product versions
–SINAUT ST7 configuration software for the PG/PC V4.0
–SINAUT TD7 library for the CPU V2.2 with new blocks for communication via P-bus
●New hardware for GSM and GPRS
–GPRS modem MD740-1 for secure packet-oriented communication via GSM mobile
wireless (GPRS)
–GSM modem MD720-3 as replacement for the discontinued GSM modem MC45 for
establishing dial-up connections via the GSM mobile wireless network; possible as of
firmware V1.7.3 of the MD720-3
Validity of the manual:
●SINAUT ST7 configuration software for the PG/PC V4.0
●SINAUT TD7 library for the CPU V2.2
●SINAUT TIM firmware V4.3.7 for the TIM 3 / TIM 4
●SINAUT TIM firmware V1.2 for the TIM 3V-IE variants

Preface
SINAUT ST7 station control system
10 System Manual, 09/2016, C79000-G8976-C178-10