Siemens SIMOTICS CONNECT 400 User manual

0QFSBUJOH*OTUSVDUJPOT$POOFDUJWJUZ.PEVMF&EJUJPO4*.05*$4$0//&$5www.siemens.com/digital-motor

SIMOTICS CONNECT 400
Operating Instructions
SIMOTICS CONNECT 400 V1.0.2.0
SIDRIVE IQ Con󹪝g (Android) V2.4.0
SIDRIVE IQ Con󹪝g (iOS) V2.4.0
SIDRIVE IQ Fleet V2.10
04/2023
A5E50161952B AL
Introduction 1
Safety instructions 2
Description 3
Preparations for use 4
Mounting and installation 5
Commissioning 6
Operation 7
Maintenance 8
Disposal 9
Further information 10

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Quali󹪝ed Personnel
The product/system described in this documentation may be operated only by personnel quali󹪝ed for the speci󹪝c
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Quali󹪝ed personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance
are required to ensure that the products operate safely and without any problems. The permissible ambient
conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identi󹪝ed by ® are registered trademarks of SiemensAG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E50161952B AL
Ⓟ 04/2023 Subject to change
Copyright © SiemensAG 2020 - 2023.
All rights reserved

Table of contents
1 Introduction ........................................................................................................................................... 7
1.1 About SIMOTICS................................................................................................................... 7
1.2 About SIMOTICS (detailed) ................................................................................................... 8
1.3 About this manual ............................................................................................................... 9
1.3.1 Content ............................................................................................................................... 9
1.3.2 Target group ........................................................................................................................ 9
1.3.3 Standard scope .................................................................................................................... 9
1.3.4 Websites of third-party companies...................................................................................... 10
1.4 SIMOTICS documentation .................................................................................................. 11
1.5 Service and Support........................................................................................................... 12
1.5.1 Siemens Industry Online Support on the Web..................................................................... 12
1.5.2 Siemens Industry Online Support on the road..................................................................... 12
1.5.3 Feedback on the technical documentation ......................................................................... 13
1.5.4 mySupport documentation ................................................................................................ 14
1.5.5 Technical support............................................................................................................... 14
1.5.6 Training ............................................................................................................................. 15
1.5.7 Spare parts services ........................................................................................................... 15
1.6 Important product information .......................................................................................... 16
1.6.1 Correct use ........................................................................................................................ 16
1.6.2 OpenSSL............................................................................................................................ 16
1.6.3 Compliance with the General Data Protection Regulation.................................................... 17
1.6.4 Compliance with the General Data Protection Regulation.................................................... 17
2 Safety instructions............................................................................................................................... 19
2.1 General safety instructions................................................................................................. 19
2.2 Quali󹪝ed personnel............................................................................................................ 20
2.3 Security information .......................................................................................................... 21
3 Description........................................................................................................................................... 23
3.1 SIDRIVE IQ Fleet ................................................................................................................. 23
3.2 "SIMOTICS CONNECT 400" connectivity module .................................................................. 24
4 Preparations for use............................................................................................................................. 27
4.1 Visual inspection................................................................................................................ 27
4.2 Shipping and storage conditions ........................................................................................ 28
4.3 Requirements .................................................................................................................... 29
5 Mounting and installation ................................................................................................................... 31
5.1 Installing the mounting bracket.......................................................................................... 32
5.2 Mounting the connectivity module..................................................................................... 35
SIMOTICS CONNECT 400
Operating Instructions, 04/2023, A5E50161952B AL 3

6 Commissioning .................................................................................................................................... 37
6.1 Requirements .................................................................................................................... 37
6.2 Commissioning with Android ............................................................................................. 38
6.2.1 Installing the "SIDRIVE IQ Con󹪝g" application ...................................................................... 38
6.2.2 Establishing the connection to the connectivity module ..................................................... 38
6.2.3 Log in with the connectivity module................................................................................... 40
6.2.4 Guided commissioning....................................................................................................... 43
6.2.4.1 Starting the commissioning wizard..................................................................................... 43
6.2.4.2 Device Credentials - Step 1/7 ............................................................................................. 43
6.2.4.3 Wi-Fi - Step 2/7................................................................................................................... 45
6.2.4.4 Firmware - Step 3/7............................................................................................................ 46
6.2.4.5 Intervals - Step 4/7 ............................................................................................................. 49
6.2.4.6 MindSphere Access - Step 5/7............................................................................................. 50
6.2.4.7 Motor Details - Step 6/7...................................................................................................... 53
6.2.4.8 Asset Info (Motor Monitoring) - Step 7/7............................................................................. 62
6.2.4.9 Asset Info (Generic Vibration monitoring) - Step 7/7 ........................................................... 69
6.3 Commissioning with iOS .................................................................................................... 74
6.3.1 Installing the "SIDRIVE IQ Con󹪝g" application ...................................................................... 74
6.3.2 Establishing the connection to the connectivity module ..................................................... 74
6.3.3 Log in with the connectivity module................................................................................... 78
6.3.4 Guided commissioning....................................................................................................... 79
6.3.4.1 Starting the commissioning wizard..................................................................................... 79
6.3.4.2 Device Credentials - Step 1/7 ............................................................................................. 80
6.3.4.3 Wi-Fi - Step 2/7................................................................................................................... 82
6.3.4.4 Firmware - Step 3/7............................................................................................................ 83
6.3.4.5 Intervals - Step 4/7 ............................................................................................................. 86
6.3.4.6 MindSphere Access - Step 5/7............................................................................................. 87
6.3.4.7 Motor Details - Step 6/7...................................................................................................... 89
6.3.4.8 Asset Info (Motor Monitoring) - Step 7/7............................................................................. 98
6.3.4.9 Asset Info (Generic Vibration monitoring) - Step 7/7 ......................................................... 104
7 Operation........................................................................................................................................... 109
7.1 Operation with Android ................................................................................................... 110
7.1.1 O󹪜boarding process using the "SIDRIVE IQ Con󹪝g" application........................................... 110
7.1.1.1 Initiating the o󹪜boarding process ..................................................................................... 110
7.1.1.2 Logging in to MindSphere ................................................................................................ 112
7.1.1.3 Executing the o󹪜boarding process.................................................................................... 114
7.1.2 Identifying the connectivity module via the "SIDRIVE IQ Con󹪝g" application....................... 114
7.1.3 Changing the measuring and send cycles ......................................................................... 115
7.1.4 Changing the user data of the connectivity module .......................................................... 117
7.1.5 Check asset data .............................................................................................................. 118
7.2 Operation with iOS .......................................................................................................... 121
7.2.1 O󹪜boarding process using the "SIDRIVE IQ Con󹪝g" application........................................... 121
7.2.2 Identifying the connectivity module via the "SIDRIVE IQ Con󹪝g" application....................... 123
7.2.3 Changing the measuring and send cycles ......................................................................... 124
7.2.4 Changing the device credentials of the connectivity module............................................. 126
7.2.5 Check asset data .............................................................................................................. 127
8 Maintenance...................................................................................................................................... 129
8.1 Updating the software and 󹪝rmware (Android)................................................................. 130
Table of contents
SIMOTICS CONNECT 400
4Operating Instructions, 04/2023, A5E50161952B AL

8.1.1 Updating the "SIDRIVE IQ Con󹪝g" application .................................................................... 130
8.1.2 Updating the connectivity module 󹪝rmware ..................................................................... 130
8.2 Updating software and 󹪝rmware (iOS).............................................................................. 133
8.2.1 Updating the "SIDRIVE IQ Con󹪝g" application .................................................................... 133
8.2.2 Updating the connectivity module 󹪝rmware (iOS)............................................................. 133
8.3 Basic functions (Android) ................................................................................................. 135
8.4 Basic functions (iOS) ........................................................................................................ 137
8.5 Replacing the connectivity module .................................................................................. 139
8.5.1 Replacing the connectivity module (hardware) ................................................................. 139
8.5.2 Commissioning the connectivity module after hardware replacement (Android) ............... 140
8.5.2.1 Starting the module replacement wizard .......................................................................... 140
8.5.2.2 Device Credentials - Step 1/7 ........................................................................................... 140
8.5.2.3 Wi-Fi - Step 2/7................................................................................................................. 142
8.5.2.4 Firmware - Step 3/7.......................................................................................................... 143
8.5.2.5 Intervals - Step 4/7 ........................................................................................................... 146
8.5.2.6 MindSphere Access - Step 5/7........................................................................................... 147
8.5.2.7 Asset Overview - Step 6/7................................................................................................. 151
8.5.2.8 Replacement reason - Step 7/7 ......................................................................................... 153
8.5.3 Commissioning the connectivity module after hardware replacement (iOS) ...................... 157
8.5.3.1 Starting the module replacement wizard .......................................................................... 157
8.5.3.2 Device Credentials - Step 1/7 ........................................................................................... 157
8.5.3.3 Wi-Fi - Step 2/7................................................................................................................. 159
8.5.3.4 Firmware - Step 3/7.......................................................................................................... 160
8.5.3.5 Intervals - Step 4/7 ........................................................................................................... 163
8.5.3.6 MindSphere Access - Step 5/7........................................................................................... 164
8.5.3.7 Asset Overview - Step 6/7................................................................................................. 167
8.5.3.8 Replacement reason - Step 7/7 ......................................................................................... 169
8.6 Replacing a motor (Android) ............................................................................................ 174
8.6.1 Start the motor replacement wizard ................................................................................. 174
8.6.2 MindSphere access .......................................................................................................... 175
8.6.3 Replacement reason - Step 1/3 ......................................................................................... 176
8.6.4 New motor data - Step 2/3 ............................................................................................... 177
8.6.5 Asset Info - Step 3/3 ......................................................................................................... 179
8.7 Replacing a motor (iOS) ................................................................................................... 185
8.7.1 Starting the motor replacement wizard ............................................................................ 185
8.7.2 MindSphere login ............................................................................................................ 186
8.7.3 Replacement Info - Step 1/3 ............................................................................................. 187
8.7.4 New motor data - Step 2/3 ............................................................................................... 188
8.7.5 Asset Info - Step 3/3 ......................................................................................................... 190
8.8 Replace the battery .......................................................................................................... 196
8.9 Changing the attachment position of the mounting bracket ............................................. 198
9 Disposal ............................................................................................................................................. 199
9.1 Disposing of the connectivity module............................................................................... 200
9.2 Disposing of the battery................................................................................................... 201
10 Further information........................................................................................................................... 203
10.1 Product information......................................................................................................... 203
Table of contents
SIMOTICS CONNECT 400
Operating Instructions, 04/2023, A5E50161952B AL 5

10.2 Product support ............................................................................................................... 204
10.3 Technical data.................................................................................................................. 206
10.4 Directives and standards .................................................................................................. 209
Index .................................................................................................................................................. 213
Table of contents
SIMOTICS CONNECT 400
6Operating Instructions, 04/2023, A5E50161952B AL

Introduction 1
1.1 About SIMOTICS
Description
SIMOTICS is the Siemens family of electric motors addressing the complete motor spectrum in
Digital Industry.
SIMOTICS CONNECT 400
Operating Instructions, 04/2023, A5E50161952B AL 7

1.2 About SIMOTICS (detailed)
With a SIMOTICS electric motor, you can always depend on quality, innovation and the highest
e󹪟ciency. With SIMOTICS electric motors we cover the complete motor spectrum:
Synchronous as well as induction motors, from standard electric motors through servomotors
for motion control applications up to high voltage and DC motors.
Siemens motors can look back on more than 150 years of experience.
Whether high e󹪟ciency for an optimum energy balance, explosion protected for the highest
safety standards, sector or customer speci󹪝c: Every motor is equipped as standard with the
widest range of features for the highest cost e󹪜ectiveness.
In a nutshell:
• Extremely compact
• Energy e󹪟cient and environmentally friendly
• Can be 󹪞exibly deployed and a wide range of selection options
• Highest degree of cost e󹪜ectiveness
In the meantime, our electric motors are an integral part of the digital enterprise.
Motors for motion control
Whether synchronous or induction, whether with or without gearbox: Siemens is the right
partner when it involves the optimum motor for your motion control application.
Our portfolio is the widest worldwide – and also includes built-in motors and motor spindles.
Every motion control motor in our portfolio is perfectly harmonized for operation with our
SINAMICS converter family.
Introduction
1.2About SIMOTICS (detailed)
SIMOTICS CONNECT 400
8Operating Instructions, 04/2023, A5E50161952B AL

1.3 About this manual
1.3.1 Content
These instructions describe the connectivity module, and provide you with information on how
to use the product – from installation through to maintenance.
Keep these instructions in a safe place for subsequent use.
In this documentation, the generic term "Connectivity module" is subsequently used for the
"SIMOTICSCONNECT400" product.
Read these instructions before you use the connectivity module, and follow the instructions
and notes carefully. In this way you can ensure safe, problem-free operation and a long
service life.
1.3.2 Target group
This documentation is intended for planners, con󹪝guring engineers, technologists, installation
personnel, programmers, commissioning personnel, service and maintenance personnel
1.3.3 Standard scope
Description
This documentation describes the functionality of the standard scope. This scope may di󹪜er
from the scope of the functionality of the system that is actually supplied. Please refer to the
ordering documentation only for the functionality of the supplied drive system.
Further functions may be executable in the system, which are not explained in this
documentation. However, there is no entitlement to these functions in the case of a new
delivery or service.
This documentation does not contain all detailed information on all types of the product.
Furthermore, this documentation cannot take into consideration every conceivable type of
installation, operation and service/maintenance.
The machine manufacturer must document any additions or modi󹪝cations they make to the
product themselves.
Introduction
1.3About this manual
SIMOTICS CONNECT 400
Operating Instructions, 04/2023, A5E50161952B AL 9

1.3.4 Websites of third-party companies
Description
This document may contain hyperlinks to third-party websites. Siemens is not responsible for
and shall not be liable for these websites and their content. Siemens has no control over the
information which appears on these websites and is not responsible for the content and
information provided there. The user bears the risk for their use.
Introduction
1.3About this manual
SIMOTICS CONNECT 400
10 Operating Instructions, 04/2023, A5E50161952B AL

1.4 SIMOTICS documentation
Description
Comprehensive documentation on SIMOTICS, SIMOGEAR and on the SINAMICS converter family
are provided in Internet.
You can display documents or download them in PDF and HTML5 format.
The documentation is divided into the following categories:
Table 1-1 SIMOTICS / SIMOGEAR / SINAMICS documentation
Information Documentation
class1)
Content Target group
General information Con󹪝guration Man‐
ual
Rules, guidelines, and tools for con󹪝g‐
uring products, systems, and plants.
Also contains information on the oper‐
ating and ambient conditions for hard‐
ware and software, the use of func‐
tions, as well as on circuit diagrams
and terminal diagrams and the instal‐
lation of software insofar as this is nec‐
essary for commissioning.
Planners, con󹪝guration engineers
Device information Installation Instruc‐
tions
All relevant information on setting up,
installing and cabling, as well as the
required dimensional drawings and cir‐
cuit diagrams
Installation personnel, commissioning
engineers, service and maintenance
personnel
Basic information Operating instruc‐
tions
Comprehensive collection of all infor‐
mation necessary for the safe opera‐
tion of products, plant/system parts
and complete plants (IEC82079)
Machine operators, plant operators
Compact instruc‐
tions
Essential contents of the operating in‐
structions in a reduced and condensed
form
Machine operators, plant operators
Product Information Information that only becomes known
shortly before or even after start of de‐
livery and is therefore not included in
the associated user documentation
Planners, con󹪝guration engineers,
technologists, installation personnel,
constructors; commissioning engi‐
neers, machine operators, program‐
mers, service and maintenance per‐
sonnel
Online help Instructions for con󹪝guring, program‐
ming, and commissioning
Con󹪝guration engineers, program‐
mers, commissioning engineers
1) Not all documentation classes are available for every SIMOTICS / SIMOGEAR / SINAMICS product.
Introduction
1.4SIMOTICS documentation
SIMOTICS CONNECT 400
Operating Instructions, 04/2023, A5E50161952B AL 11

1.5 Service and Support
1.5.1 Siemens Industry Online Support on the Web
Description
The following is available via Siemens Industry Online Support (https://
support.industry.siemens.com/cs/ww/en/), among others:
• Product support
• Global forum for information and best practice sharing between users and specialists
• Local contact persons via the contact person database (→ Contact)
• Information about 󹪝eld services, repairs, spare parts, and much more (→ Services)
• Search for product info
• Important topics at a glance
• FAQs (frequently asked questions)
• Application examples
• Manuals
• Downloads
• Compatibility tool
• Newsletters with information about your products
• Catalogs/brochures
1.5.2 Siemens Industry Online Support on the road
Description
Figure1-1 "Siemens Industry Online Support" app
Introduction
1.5Service and Support
SIMOTICS CONNECT 400
12 Operating Instructions, 04/2023, A5E50161952B AL

The "Industry Online Support" app supports you in the following areas, for example:
• Resolving problems when executing a project
• Troubleshooting when faults develop
• Expanding a system or planning a new system
Furthermore, you have access to the Technical Forum and other articles that our experts have
drawn up:
• FAQs
• Application examples
• Manuals
•Certi󹪝cates
• Product announcements and much more
There is a data matrix code or QR code on the nameplate of your product. Scan the code
using the "Industry Online Support" app to obtain technical information about the device.
The app is available for AppleiOS and Android.
1.5.3 Feedback on the technical documentation
Description
We welcome your questions, suggestions, and corrections for this technical documentation.
Please use the "Provide feedback" link at the end of the entries in Siemens Industry Online
Support.
Figure1-2 Requests and feedback
Introduction
1.5Service and Support
SIMOTICS CONNECT 400
Operating Instructions, 04/2023, A5E50161952B AL 13

1.5.4 mySupport documentation
Description
With the "mySupport documentation" web-based system, you can compile your own individual
documentation based on Siemens content and adapt this for your own machine documentation.
To start the application, click the "My Documentation" tile on the mySupport homepage
(https://support.industry.siemens.com/cs/ww/en/my):
Figure1-3 mySupport
The con󹪝gured manual can be exported in the PDF or XML format.
Siemens content that supports the mySupport documentation can be identi󹪝ed by the
"Con󹪝gure" link.
1.5.5 Technical support
Description
Your routes to technical support (https://support.industry.siemens.com/cs/ww/en/sc/4868):
• Support Request (https://www.siemens.com/SupportRequest)
• Contact person database (https://www.automation.siemens.com/aspa_app)
• "Industry Online Support" mobile app
The Support Request is the most important input channel for questions relating to products
from Siemens Industry. This will assign your request a unique ticket number for tracking
purposes. The Support Request o󹪜ers you:
• Direct access to technical experts
• Recommended solutions for various questions (e.g. FAQs)
• Status tracking of your requests
Introduction
1.5Service and Support
SIMOTICS CONNECT 400
14 Operating Instructions, 04/2023, A5E50161952B AL

Technical support also assists you in some cases via remote support (https://
support.industry.siemens.com/cs/de/en/view/106665159) to resolve your requests. A
Support representative will assist you in diagnosing or resolving the problem through screen
transfer.
More information on the Support service packages is available on the Internet via the
following address (https://support.industry.siemens.com/cs/ww/en/sc/4869).
1.5.6 Training
Description
SITRAIN – Digital Industry Academy o󹪜ers a comprehensive range of training courses on
Siemens industrial products – directly from the manufacturer, for all industries and use cases, for
all knowledge levels from beginner to expert.
More information can be found on the Internet via the following address (https://
www.siemens.com/sitrain).
1.5.7 Spare parts services
Description
By using the online spare parts service "Spares on Web", you ensure the smooth operation of
your product. The spare parts service is aimed at the following:
• Improved spare parts inventories by balancing stock and spare parts on call
• Minimized downtimes during a plant standstill
• Reduced costs
More information can be found on the Internet via the following address (https://
www.sow.siemens.com).
Introduction
1.5Service and Support
SIMOTICS CONNECT 400
Operating Instructions, 04/2023, A5E50161952B AL 15

1.6 Important product information
1.6.1 Correct use
Description
The products described in this manual, together with software, accessories, and options, form
an electrical power drive system intended to feed low-voltage AC motors. The products are
professional equipment for use in industrial applications. The products must be installed and
maintained by professionals with su󹪟cient knowledge to implement the safety and EMC
measures according to the speci󹪝cations described in this manual and the recognized state
ofthe art.
You may only use the products in compliance with the following requirements:
• All regulations and directives that are applicable at the site of the end use, especially with
regard to electrical safety, functional safety and electromagnetic compatibility.
• All instructions, notes, technical data and safety information contained in this manual and
other supporting documentation.
Before using the products, you must perform a risk assessment of the entire application and
implement appropriate system design measures to ensure safety of persons, property and
electromagnetic compatibility.
Open type products (IP00/IP20) are intended for incorporation within cubicles or enclosures
which will provide necessary protection.
Any use other than the use explicitly permitted is prohibited and can result in unanticipated
hazards.
1.6.2 OpenSSL
Description
This product can contain the following software:
• Software developed by the OpenSSL project for use in the OpenSSL toolkit
• Cryptographic software created by Eric Young.
• Software developed by Eric Young
You can 󹪝nd more information on the internet:
• OpenSSL (https://www.openssl.org)
• Cryptsoft (https://www.cryptsoft.com)
Introduction
1.6Important product information
SIMOTICS CONNECT 400
16 Operating Instructions, 04/2023, A5E50161952B AL

1.6.3 Compliance with the General Data Protection Regulation
Description
Siemens complies with the principles of the General Data Protection Regulation (EU), in
particular the principle of data minimization (privacy by design). For this SINAMICS product, this
means:
•User management and access control (UMAC)
The product processes or stores the following personal data:
– Login data for user management and access control:
User name, group, password, role, rights.
The data for user management and access control are stored in the converter and optionally
on a memory card.
•Support data (optional)
For optimal support in service cases, the end user or machine manufacturer (OEM) can
optionally store contact data (header, email address, telephone number, homepage) in the
converter.
If these data are created, the author must give thought to data protection consent for these
optional data. Siemens takes no responsibility for these data.
These support contact data can be read and are freely accessible in, for example, the user
interface as well as in the diagnostics report. These data are not encrypted.
These data are used for user management and access control (UMAC) and for the support
function. The storage of these data is appropriate and limited to what is necessary, as it is
essential to identify the authorized operators and service contact.
The personal data are also available as part of the backup system to ensure fast recovery of
use cases.
The above-mentioned personal data cannot be stored anonymously or pseudonymized,
as they serve the purpose of identifying the operating personnel. The anonymization or
pseudonymization, e.g. of the login data, must be performed using suitable login names and
contact data by the plant/machine operator.
Our product does not provide any functions for automatically deleting personal data.
Individual UMAC data can be deleted manually by authorized personnel as soon as this is
deemed recommended/required.
1.6.4 Compliance with the General Data Protection Regulation
Description
Siemens complies with the principles of the General Data Protection Regulation (EU), in
particular the principle of data minimization ("privacy by design").
Introduction
1.6Important product information
SIMOTICS CONNECT 400
Operating Instructions, 04/2023, A5E50161952B AL 17

For SINAMICS DCB Studio, this means:
•User administration
The product processes or stores the following personal data:
– Login data for user administration: user name.
The data for user administration is stored in the generated library. The data is not encrypted.
This data is required for user administration. The storage of this data is appropriate and
limited to what is necessary, as it is essential to identify the creator of the library. This is
particularly important during servicing.
The above-mentioned personal data cannot be stored anonymously or pseudonymized, as
it serves to identify the creator of the library. The creator of the library must anonymize or
pseudonymize the login data by selecting suitable user names.
Our product does not provide any functions for automatically deleting personal data.
Introduction
1.6Important product information
SIMOTICS CONNECT 400
18 Operating Instructions, 04/2023, A5E50161952B AL