Siemens SITOP UPS1600 under STEP 7 V12 User manual

SITOP UPS1600 under STEP 7 V12
___________________
___________________
___________________
___________________
___________________
SITOP UPS1600 under STEP 7
V12
Getting Started
Introduction
1
Safety notes
2
Description
3
Assigning the IP address
4
Installing and configuring the
SITOP UPS1600 in STEP 7
V12
5
Parameterizing the SITOP
UPS1600
6

Siemens AG
Industry
Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
Ⓟ
02/2014 Technical data subject to change
Copyright © Siemens AG .
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SITOP UPS1600 under STEP 7 V12
Getting Started, 3
Table of contents
1 Introduction...................................................................................................................................5
1.1 Purpose of this document......................................................................................................... 5
1.2 Technical support..................................................................................................................... 5
1.3 Additional documentation ......................................................................................................... 6
2 Safety notes .................................................................................................................................7
3 Description ...................................................................................................................................9
3.1 System overview...................................................................................................................... 9
4 Assigning the IP address.............................................................................................................. 11
5 Installing and configuring the SITOP UPS1600 in STEP 7 V12 ......................................................... 17
6 Parameterizing the SITOP UPS1600 ............................................................................................. 25
6.1 Buffering an S7 IO controller, including the I/O when the power fails....................................... 25
6.2 Switching off the UPS when the power fails by a user program............................................... 29

SITOP UPS1600 under STEP 7 V12
Getting Started, 5
Introduction
1
1.1
Purpose of this document
This Getting Started guides you through configuring the UPS1600 under STEP 7 V12 for the
following two tasks:
●Buffering the S7 IO controller, including the I/O when the power fails
●Switching off the UPS when the power fails by the user program
Basic knowledge required
The following are required to understand the Getting Started:
●Knowledgeable about using personal computers with the Windows operating system
●Knowledgeable about how to configure an uninterruptible power supply using the
UPS1600, including the S7 IO controller and connected battery modules
●Creating and editing projects under STEP 7 V12 in the TIA-Portal.
Range of validity
Getting Started is valid for STEP 7 V12, Version 12.0 with service pack 1 (SP1).
1.2
Technical support
Technical support
Technical support for all IA/DT products can be accessed through the following
communication channels:
●Phone: + 49 (0) 911 895 7222
●E-Mail (mailto:[e-mail])
●Internet:
Online support request form (http://www.siemens.com/automation/support-request)
Technical documentation on the Internet
Operating instructions and manuals for SITOP are available in the Internet:
Operating instructions/manuals (http://www.siemens.com/sitop/manuals)
SITOP power supply homepage
General news about our power supplies is available in the Internet at the SITOP home page
(http://www.siemens.com/sitop).

Introduction
1.3 Additional documentation
SITOP UPS1600 under STEP 7 V12
6Getting Started,
1.3
Additional documentation
Further information is available in the following documents:
●UPS1600 and UPS1100 manuals
●IO controller manual
●STEP 7 V12 manual

SITOP UPS1600 under STEP 7 V12
Getting Started, 7
Safety notes
2
WARNING
Correct handling of the devices
When operating electrical devices, it is inevitable that certain components will carry
dangerous voltages.
Therefore, failure to handle the units properly can result in death or serious physical injury
as well as extensive property damage.
Only appropriately qualified personnel may work on or in the vicinity of this equipment.
Perfect, safe, and reliable operation of this equipment is dependent on proper
transportation, storage, installation and mounting.
Before installation or maintenance work can begin, the system's main switch must be
switched off and measures taken to prevent it being switched on again.
If this instruction is not observed, touching live parts can result in death or serious injury.
The relevant DIN/VDE regulations or country-specific specifications (e.g. VDE 0510 Part 2 /
EN50272-2) must be observed for the storage, assembly and operation of the lead
accumulators. It must be ensured that the battery location is suitably ventilated. Potential
ignition sources must be separated by at least 50 cm.

SITOP UPS1600 under STEP 7 V12
Getting Started, 9
Description
3
3.1
System overview
Application
The principal tasks that you can perform with the SITOP UPS Management:
●Connecting the uninterruptible SITOP UPS1600 power supply to the IO controller S7
●Configuring the SITOP UPS1600 uninterruptible power supply
●Protecting a computer or a computer network using the uninterruptible power supply
●Defining the battery maintenance intervals
Device integration
SITOP UPS Management supports the following devices:
●UPS1600
●UPS1100
UPS1600 can be used with STEP 7 V12 as of version 12.0 with Servicepack 1 (SP1).
After the UPS1600 has been saved in the hardware catalog of STEP 7 V12 by installing the
hardware support package, it can be integrated into projects, parameterized and diagnosed.
Languages
German, English
French, Italian, Spanish and Chinese being prepared.