Siemens SIMATIC IOT2050 User manual

SIMATIC IOT2050 Starterkit
SIMATIC IOT2050 Starterkit
Product Information
06/2021
A5E50831253
-AA
Package list
1
Preparing for installation
2
Mounting the device
3
Connecting the device
4
Installing the IOT2000
Input/Output Module
5
Insert Micro SD card
6

Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E50831253-AA
Ⓟ
05/2021 Subject to change
Copyright © Siemens AG 2021.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SIMATIC IOT2050 Starterkit
Product Information, 06/2021, A5E50831253-AA 3
Table of contents
1 Package list ............................................................................................................................................ 4
2 Preparing for installation....................................................................................................................... 6
2.1 Checking the delivery........................................................................................................... 6
2.2 Identification data of the device........................................................................................... 8
2.3 Permitted mounting positions and mounting types .............................................................. 8
3 Mounting the device ........................................................................................................................... 10
3.1 Mounting instructions........................................................................................................ 10
3.2 Mounting on DIN rails ........................................................................................................ 11
3.2.1 Secure the mounting clips.................................................................................................. 11
3.2.2 Mounting on DIN rails ........................................................................................................ 13
3.3 Wall mounting ................................................................................................................... 14
3.3.1 Vertical wall mounting....................................................................................................... 14
3.3.2 Horizontal wall mounting................................................................................................... 15
4 Connecting the device......................................................................................................................... 16
4.1 Notes on connecting.......................................................................................................... 16
4.2 Connecting the function earth ........................................................................................... 17
4.3 Connecting the power supply............................................................................................. 19
5 Installing the IOT2000 Input/Output Module ...................................................................................... 20
6 Insert Micro SD card............................................................................................................................. 23
Index .................................................................................................................................................... 24

SIMATIC IOT2050 Starterkit
4Product Information, 06/2021, A5E50831253-AA
Package list
1

Package list
SIMATIC IOT2050 Starterkit
Product Information, 06/2021, A5E50831253-AA 5
IOT2050 Starterkit contains the following components:
Quantity
Name
Specification
1
SIMATIC IOT2050
6ES7647-0BA20-0SP2
1
SIMATIC IOT2000 In-
put/Output Module
A5E39310827
5 x DI, 2 x AI, 2 x DO
1
Cover for Input/Output
Module and three plastic
mounting clamps
A5E50613788
1
SD card (Inserted in
IOT2050)
8 GB
1
Power adapter
AC-DC Power supply, 12 V
1
Network cable
RJ45 cable, 1.5 m
1
Accessory Kit
Mounting bracket, mounting clamps and
screws
1
Quick Install Guide
Printed paper
1
OSS Readme
Printed paper
1
Important notes on your
device
Printed paper
Note: Additional information on the software topics, commissioning and Micro SD image is
available in the SIMATIC IOT2000 Forum (http://www.siemens.com/automation/forum).

SIMATIC IOT2050 Starterkit
6Product Information, 06/2021, A5E50831253-AA
Preparing for installation
2
2.1 Checking the delivery
Procedure
1. When accepting a delivery, please check the packaging for visible transport damage.
If any transport damage is present at the time of delivery, lodge a complaint at the
shipping company in charge. Have the shipper confirm the transport damage
immediately.
2. Unpack the device at its installation location.
3. Keep the original packaging in case you have to transport the unit again.
Note
Damage to the d
evice during transport and storage
If a device is transported or stored without packaging, shocks, vibrations, pressure and
moisture may impact the unprotected unit. A damaged packaging indicates that ambient
conditions have already had a massive impact on
the device.
The device might be damaged.
Do not dispose of the original packaging. Pack the device during transportation and
storage.
4. Check the contents of the packaging and any accessories you may have ordered for
completeness and damage.
–Device
–DC connecting terminal, already plugged into the device.
–One mounting accessory kit including: 1 x Rail clamp, 2 x mounting brackets and
screws.

Preparing for installation
2.1 Checking the delivery
SIMATIC IOT2050 Starterkit
Product Information, 06/2021, A5E50831253-AA 7
5. If the contents of the packaging are incomplete, damaged or do not match your order,
inform the responsible delivery service immediately.
WARNING
Electric shock and fire hazard due to damaged device
A damaged device can be under hazardous voltage and trigger a fire in the machine or
plant. A damaged device has unpredictable properties and states.
Death or serious injury could occur.
Make sure that the damaged device is not inadvertently installed and put into operation.
Label the damaged device and keep it locked away. Send off the device for immediate
repair.
NOTICE
Damage from condensation
If the device is subjected to low temperatures or extreme fluctuations in temperature
during transportation, for example in cold weather, moisture could build up on or inside
the device (condensation).
Moisture causes a short circuit in electrical circuits and damages the device.
In order to prevent damage to the device, proceed as follows:
•Store the device in a dry place.
•Bring the device to room temperature before starting it up.
•Do not expose the device to direct heat radiation from a heating device.
•If condensation develops, wait approximately 12 hours or until the device is
completely dry before switching it on.
6. Keep the enclosed documentation in a safe place. You need the documentation when you
commission the device for the first time.
7. Write down the identification data of the device.

Preparing for installation
2.2 Identification data of the device
SIMATIC IOT2050 Starterkit
8Product Information, 06/2021, A5E50831253-AA
2.2 Identification data of the device
The device can be clearly identified with the help of this identification data in case of repairs
or theft.
You can find this information on the rating plate. The following illustration shows an
example.
Example rating plate:
Enter the identification data in the table below:
Order number
6ES ...
Serial number
S V
Production version
FS
All existing Ethernet ad-
dresses (MAC)
2.3 Permitted mounting positions and mounting types
The device can be mounted horizontally or vertically on a DIN rail or to a wall.
Vertical mounting position, preferred
Horizontal mounting position

Preparing for installation
2.3 Permitted mounting positions and mounting types
SIMATIC IOT2050 Starterkit
Product Information, 06/2021, A5E50831253-AA 9
Consider the permitted temperature range for operation that depends on the mounting
position.
Mounting type
Ambient temperature for operation
Rail mounting
•Vertical: 0 to 50 °C
•
Horizontal: 0 to 40 °C
Wall mounting
•Vertical: 0 to 45 °C
•Horizontal: 0 to 40 °C
Clearances
Ensure that the following clearances measurements to another component or to a wall of a
housing are complied with:
•Below the device: ≥50 mm
•Above the device: ≥50 mm

SIMATIC IOT2050 Starterkit
10 Product Information, 06/2021, A5E50831253-AA
Mounting the device
3
3.1 Mounting instructions
Note the following:
•The device is approved for indoor operation only.
•For installation in a cabinet, observe the SIMATIC setup guidelines
(http://support.automation.siemens.com/WW/view/de/1064706) as well as the relevant
DIN/VDE requirements or the applicable country-specific regulations.
•When the device is used in the area of Industrial Control Equipment in accordance with
UL61010-2-201, note that the device is classified as "Open equipment".
•Siemens recommends you use 0.6 Nm tightening torque to install the mounting clamps
and brackets.
Fasten securely
NOTICE
Insufficient load carrying capacity
If the mounting surface for wall mounting does not have an enough load-bearing capacity,
the device may fall and be damaged.
Ensure that the mounting surface on the wall can bear four times the total weight of the
device, including fixing elements.
NOTICE
Incorrect fixing elements
If you use anchors and screws other than those specified below for wall mounting, safe
mounting is not guaranteed. The device can fall and may be damaged.
Only use the anchors and screws specified in the following table.
Material
Bore diameter
Fixing element
Concrete
Select according to the specifi-
cation of the mounting ele-
ments used
•Anchor, ∅6 mm, 40 mm long
•
Screw, ∅4 mm, 40 mm long
Plasterboard,
(at least 13 mm thick)
Toggle plug, ∅12 mm, 50 mm
long
Metal,
(at least 2 mm thick) •Screw M4 × 15
•M4 nut

Mounting the device
3.2 Mounting on DIN rails
SIMATIC IOT2050 Starterkit
Product Information, 06/2021, A5E50831253-AA 11
3.2 Mounting on DIN rails
3.2.1 Secure the mounting clips
Requirement
•The DIN rail is installed at the installation site (35 mm standard profile).
•Mounting bracket and mounting clamps
•Two screws
•T8 screwdriver
Secure the mounting clips for vertical mounting
1.
Lay the rail clamp on the rear of
the device.
2.
Fasten the rail clamp with the
supplied screws.

Mounting the device
3.2 Mounting on DIN rails
SIMATIC IOT2050 Starterkit
12 Product Information, 06/2021, A5E50831253-AA
Secure the mounting clips for horizontal mounting
1.
Lay the rail clamp on the rear of
the device.
2.
Fasten the rail clamp with the
two supplied screws.
3.
Lay the brackets on the rear of
the device. Align the bracket edge
with the device edge.
4.
Fasten the brackets with the
supplied screws.

Mounting the device
3.2 Mounting on DIN rails
SIMATIC IOT2050 Starterkit
Product Information, 06/2021, A5E50831253-AA 13
3.2.2 Mounting on DIN rails
Mounting
1.
Place the device and rail clamp on the upper edge of the standard profile rail at the position
shown and push the device down.
2.
Swing the rail clamp of the device from below through the standard profile rail.
3.
Push the device in the direction of the standard profile rail. You will hear the device click into
place.
Vertical
Horizontal
Removing
1. Push down the device until it is released by the rail clamp.
2. Swing the device out of the standard profile rail.
3. Lift the device up and off.

Mounting the device
3.3 Wall mounting
SIMATIC IOT2050 Starterkit
14 Product Information, 06/2021, A5E50831253-AA
3.3 Wall mounting
3.3.1 Vertical wall mounting
The device is suitable for horizontal or vertical wall mounting.
Note
The device must be installed on the plate of an enclosure.
Requirement
•Two mounting brackets
•Two screws
•T8 screwdriver
Procedure for mounting
1.
Lay the mounting brackets on the rear of the device.
2.
Fasten the brackets with supplied screws.
3.
Mark the bore holes, drill the required holes in the wall and fasten the device to the wall
using two screws.

Mounting the device
3.3 Wall mounting
SIMATIC IOT2050 Starterkit
Product Information, 06/2021, A5E50831253-AA 15
3.3.2 Horizontal wall mounting
The device is suitable for horizontal or vertical wall mounting.
Requirement
•Two mounting brackets
•Two screws
•T8 screwdriver
Procedure for mounting
1.
Lay the mounting brackets on the rear of the device.
2.
Fasten the brackets with supplied screws.
3.
Mark the bore holes, drill the required holes in the wall and fasten the device to the wall
using two screws.

SIMATIC IOT2050 Starterkit
16 Product Information, 06/2021, A5E50831253-AA
Connecting the device
4
4.1 Notes on connecting
WARNING
Risk of lightning strikes
A lightning flash may enter the mains cables and data transmission cables and jump to a
person.
Death, serious injury and burns can be caused by lightning.
Take the following precautions:
•Disconnect the device from the power supply in good time when a thunderstorm is
approaching.
•Do not touch mains cables and data transmission cables during a thunderstorm.
•
Keep an enough distance from electric cables, distributors, systems, etc.
CAUTION
Use copper cables at connectors with terminal connections
Use copper (Cu) cables for all supply lines that are connected to the device with terminals,
e.g. 24 VDC power supply cables to the 24 VDC power supply connectors.
Utiliser des câbles en cuivre sur les connexions à bornes
Utilisez des câbles en cuivre (Cu) pour tous les câbles d'alimentation qui sont raccordés à
l'appareil par des bornes, par exemple les câbles d'alimentation 24 V CC sur le connecteur
d'alimentation 24 V CC.
NOTICE
Fault caused by I/O devices
The connection of I/O devices can cause faults in the device.
The result might be personal injury and damage to the machine or plant.
Note the following when connecting I/O devices:
•Read the documentation of the I/O devices. Follow all instructions in the documentation.
•Only connect I/O devices which are approved for industrial applications in accordance
with EN 61000-6-2 and IEC 61000-6-2.
•I/O devices that are not hotplug-capable may only be connected after the device has
been disconnected from the power supply.

Connecting the device
4.2 Connecting the function earth
SIMATIC IOT2050 Starterkit
Product Information, 06/2021, A5E50831253-AA 17
NOTICE
Damage through regenerative feedback
Regenerative feedback of voltage to ground by a connected or installed component can
damage the device.
Connected or built-in I/Os, for example, a USB drive, are not permitted to supply any voltage
to the device. Regenerative feedback is generally not permitted.
NOTICE
Ferrite required at USB cables
The interference immunity of the device according to the data in the technical specifications
is only guaranteed when the cables at USB and micro USB ports are equipped with a ferrite
magnet. Use only USB cables equipped with a ferrite magnet.
4.2 Connecting the function earth
A connected function earth discharges electrical charges from the metal enclosure.
The function earth also improves the discharge of interference generated by external power
cables, signal cables or cables for I/O modules to ground.
The connection for the function earth is labeled with the following symbol:
WARNING
Electric shock and risk of fire
High voltage may be present in a defective device, which can cause fire or an electric shock
if touched. This can result in death and serious injury.
•Connect the device to the function earth before you put it into operation.
•
The function earth terminal on the device must be connected to the function earth of the
control cabinet or system in which the device is installed.
•Never operate the device without function earth.
•
If a device is defective, remove it from operation without delay and label it accordingly.

Connecting the device
4.2 Connecting the function earth
SIMATIC IOT2050 Starterkit
18 Product Information, 06/2021, A5E50831253-AA
Requirement
•T20 screwdriver
•Cable lug for M4
•Function earth with minimum cross-section of 2.5 mm2copper cable
Procedure
Clamp the cable lug on the function earth.
Firmly attach the cable lug to the function earth connection
on the device using the M4 thread with the torque of 1 Nm
(see part labeled).
Connect the function earth to the protective conductor con-
nection of the cabinet or the plant in which the device is in-
stalled.

Connecting the device
4.3 Connecting the power supply
SIMATIC IOT2050 Starterkit
Product Information, 06/2021, A5E50831253-AA 19
4.3 Connecting the power supply
Note
The device should only be connected to a 12 to 24 V DC power supply which meets the
requirements of safe extra low voltage (SELV) according to IEC/EN/DIN EN/UL 61010-1.
Note
The power supply m
ust be adapted to the input data of the device.
If there are voltage peaks on power supply lines, use a protective device in the form of a
varistor (MOV) UMOV = U-rated x 1.2 (BLITZDUCTOR BVT AVD 24 (918 422) or compatible).
Requirement
•You are using the supplied terminal.
•A slotted screwdriver with a 3 mm blade.
Procedure
1. Switch off the power supply.
2. Connect the power cable and the adapter.
3. Connect the connecting terminal to the connection for the power supply.

SIMATIC IOT2050 Starterkit
20 Product Information, 06/2021, A5E50831253-AA
Installing the IOT2000 Input/Output Module
5
Note
If the equipment is used in manner not specified by the manufacture, the protection provided
by the equipment may be impaired.
Requirements
•IOT2050 is disconnected from the power supply.
WARNING
Risk of fire and electric shock
The on/off switch does not isolate the device from the power supply. Risk of electric shock if
the device is opened incorrectly or defective. There is also a risk of fire if the device or
connecting lines are damaged. Death or serious bodily injury can result.
You should therefore protect the device as follows:
•Always pull out the power plug when you are not using the device or if the device is
defective. The power plug must be freely accessible.
•
Use a central power isolating switch for cabinet installation.