Siemens NEC Article 409 User manual

Reference Manual
Industrial Controls
Short-circuit current rating (SCCR) of industrial control panels
06/2013Edition
Answers for industry.

Short-circuit current rating (SCCR) of
industrial control panels
___________________
___________________
___________________
___________________
NEC Article 409 and UL 508A
Short-circuit current rating (SCCR)
of industrial control panels
Reference Manual
06/2013
A5E31896849002A/RS
-AA/001
Introduction
1
Overview of NEC Article 409
2
Overview of Supplement SB
from the UL 508A standard
3
Basic steps for calculating
the SCCR of a control panel
4
Flow chart for calculating the
SCCR of a component
5

Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E31896849002A/RS-AA/001
Ⓟ06/2013 Technical data subject to change
Copyright © Siemens AG 2013.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Short-circuit current rating (SCCR) of industrial control panels
Reference Manual, 06/2013, A5E31896849002A/RS-AA/001 5
Table of contents
1 Introduction............................................................................................................................................. 7
2 Overview of NEC Article 409 ................................................................................................................... 9
3 Overview of Supplement SB from the UL 508A standard....................................................................... 11
4 Basic steps for calculating the SCCR of a control panel......................................................................... 13
4.1 SB4.2 – Determining the short-circuit current ratings (SCCR) of individual power circuit
components..................................................................................................................................13
4.1.1 Basic: Device markings or component instruction sheets ...........................................................13
4.1.2 Basic: Assumed short-circuit current rating .................................................................................14
4.1.3 Basic: Tested combination of devices according to UL508 .........................................................14
4.2 SB4.3 – Adaptation of the available short-circuit current rating based on the peak let-
through currents when using current-limiting devices in the feeder circuit ..................................18
4.2.1 Current-limiting transformers .......................................................................................................18
4.2.2 Current-limiting circuit breakers (according to UL489) ................................................................18
4.2.3 Current-limiting fuses ...................................................................................................................20
4.3 SB4.4 – SCCR calculation of the industrial control panel............................................................23
5 Flow chart for calculating the SCCR of a component ............................................................................. 25
5.1 Calculation of the short-circuit current rating of an individual power circuit component
according to UL 508A SB4.2........................................................................................................25
5.2 Calculation of the short-circuit current rating of current-limiting feeder components ..................26
5.3 Calculation of the short-circuit current rating of a control panel in accordance with
UL 508A Supplement SB 4.4.......................................................................................................28

Table of contents
Short-circuit current rating (SCCR) of industrial control panels
6Reference Manual, 06/2013, A5E31896849002A/RS-AA/001

Short-circuit current rating (SCCR) of industrial control panels
Reference Manual, 06/2013, A5E31896849002A/RS-AA/001 7
Introduction
1
Article 409 on Industrial Control Panels was added to the NEC (National Electrical Code) in
its 2005 edition. This Article requires all Industrial Control Panels to be marked with a short-
circuit current rating. The short-circuit current rating (SCCR) requirements for UL 508A came
into force in April 2006. These changes impact control panel builders, OEMs and end users
in a number of different ways:
●The correct choice of power circuit components of a control panel
●Specification of preferred device manufacturers
●Design and marking of panels
●Correct installation and modification of control panels
Siemens is committed to supplying best-in-class products and services to our customers.
Siemens provides extensive product documentation to enable its customers to comply with
NEC Article 409 and the UL 508A standard.
Guide
This document includes the following information:
●Overview of NEC Article 409
●Overview of Supplement SB of the UL 508A standard with relevant examples
●Process flow charts
–Calculating the SCCR value of a component
–Calculating the SCCR with current-limiting feeder components
–Calculation of the SCCR of a control panel
Further information about UL / NFPA
Underwriters Laboratories UL (http://www.ul.com)
UL online certifications directory (http://www.ul.com/database)
National Fire Protection Association NFPA (http://www.nfpa.org)

Introduction
Short-circuit current rating (SCCR) of industrial control panels
8Reference Manual, 06/2013, A5E31896849002A/RS-AA/001

Short-circuit current rating (SCCR) of industrial control panels
Reference Manual, 06/2013, A5E31896849002A/RS-AA/001 9
Overview of NEC Article 409
2
The "NFPA 70: National Electrical Code" includes "Article 409" on the Construction of
Industrial Control Panels operating at 600 volts or less.
Section 409.2: definition of industrial control panels
Section 409.2 defines an industrial control panel as:
"An assembly of two or more components consisting of one of the following:
1. Power circuit components only, such as motor controllers, overload relays, fused
disconnect switches, and circuit breakers
2. Control circuit components only, such as pushbuttons, pilot lights, selector switches,
timers, switches, control relays
3. A combination of power and control circuit components"
These components are mounted in an enclosure or panel with the associated wiring and
terminals.
The industrial control panel does not include the controlled equipment.
Section 409.110: Marking of the short-circuit current rating
Section 409.110 requires a short-circuit current rating (SCCR) to be marked on all industrial
control panels. This rating must be based on the rating of a listed and labeled assembly or
on another approved method for determining the rating. It also includes a fine print note
(FPN) reference to UL 508A Supplement SB as an example of an approved method for
determining the SCCR that may be marked on the panel.

Overview of NEC Article 409
Short-circuit current rating (SCCR) of industrial control panels
10 Reference Manual, 06/2013, A5E31896849002A/RS-AA/001

Short-circuit current rating (SCCR) of industrial control panels
Reference Manual, 06/2013, A5E31896849002A/RS-AA/001 11
Overview of Supplement SB from the UL 508A
standard
3
Components in the power circuit
UL508A is the safety standard for industrial control panels.
NEC Article 409 references UL508A Supplement SB as an approved method for determining
the SCCR of an industrial control panel. The specific method is outlined in Section SB4.
The SCCR of the control panel is based on the SCCR of each component in the power
circuit. The component with the lowest SCCR defines the SCCR of the entire panel.
Paragraph SB4.2.1 and Table SB4.1 list the following components as part of the power
circuit:
Disconnect switches
Supplementary protectors
Branch circuit protective devices
Busbars
Fuseholders
Current meters
Load controllers
Current shunts
Motor overload relays
Switch units
Receptacles Terminal blocks or power distribution
blocks
Paragraph SB3.2.1 states that the primary short-circuit protective device for the control
circuit is also included in the calculation for the SCCR for the power circuit. Therefore, the
SCCR of the overcurrent protective devices (except for supplementary protectors recognized
according to UL1077 or sets of supplemental fuses recognized according to UL248-13) are
included in calculation of the SCCR of the control panel. Control circuit components on the
load side of these devices are not included in calculation of the SCCR.

Overview of Supplement SB from the UL 508A standard
Short-circuit current rating (SCCR) of industrial control panels
12 Reference Manual, 06/2013, A5E31896849002A/RS-AA/001

Short-circuit current rating (SCCR) of industrial control panels
Reference Manual, 06/2013, A5E31896849002A/RS-AA/001 13
Basic steps for calculating the SCCR of a control
panel
4
4.1
SB4.2 – Determining the short-circuit current ratings (SCCR) of
individual power circuit components
The short-circuit strength of individual power circuit components can be calculated using
three possible methods:
●Based on device markings or component instruction sheets
●Based on assumed short-circuit current rating
●Based on tested combinations of devices according to UL508
4.1.1
Basic: Device markings or component instruction sheets
Most Siemens power control and circuit protection components include a standard short
circuit rating on the front or on the nameplate.
Example of marking on a 3RT contactor
Figure 4-1 Nameplate
Exception
The short-circuit current rating of Siemens frequency converters is stated in the operating
instructions or the relevant catalogs. This complies with the requirements of NEC Article 409
and is therefore entered in the relevant UL test reports.
Moreover, in the case of frequency converters that are protected with fuses, circuit breakers
according to UL489 or self-protected combination motor controllers per UL508 type E, the
short-circuit current rating of the drive in conjunction with the line-side protective device is
stated.

Basic steps for calculating the SCCR of a control panel
4.1 SB4.2 – Determining the short-circuit current ratings (SCCR) of individual power circuit components
Short-circuit current rating (SCCR) of industrial control panels
14 Reference Manual, 06/2013, A5E31896849002A/RS-AA/001
4.1.2
Basic: Assumed short-circuit current rating
For unmarked components, the assumed maximum short-circuit current rating in accordance
with Table SB4.1 (see extract) can be used for calculating the short-circuit current rating.
Figure 4-2 Table SB4.1: Assumed maximum short-circuit current rating for unmarked components
(extract)
4.1.3
Basic: Tested combination of devices according to UL508
To increase the short-circuit current rating of a device, an appropriate protective device must
be connected on the line side of it. Which protective device is suitable is stated in the
relevant UL test report of the device whose short-circuit current rating is to be increased.
UL test report
Example: A 3RT2015 contactor has a default value of 5 kA according to its rating plate. The
UL test report states the protective devices with which the short-circuit current rating can be
increased.
Figure 4-3 Extract from the UL test report

Basic steps for calculating the SCCR of a control panel
4.1 SB4.2 – Determining the short-circuit current ratings (SCCR) of individual power circuit components
Short-circuit current rating (SCCR) of industrial control panels
Reference Manual, 06/2013, A5E31896849002A/RS-AA/001 15
Download: certificates of compliance
Certificates of Compliance (http://www.siemens.com/sirius/support) for switching devices can
be downloaded on the Internet. These contain the contents of the UL test reports that are
relevant for configuration.
Figure 4-4 Support: certificate download 1
Figure 4-5 Support: certificate download 2

Basic steps for calculating the SCCR of a control panel
4.1 SB4.2 – Determining the short-circuit current ratings (SCCR) of individual power circuit components
Short-circuit current rating (SCCR) of industrial control panels
16 Reference Manual, 06/2013, A5E31896849002A/RS-AA/001
Figure 4-6 Support: certificate download 3
Figure 4-7 Support: certificate download 4
General information and relevant product documentation (including configuration manuals)
relating to North America are also available on the Internet
(www.siemens.com/applicationconsulting/ul).

Basic steps for calculating the SCCR of a control panel
4.1 SB4.2 – Determining the short-circuit current ratings (SCCR) of individual power circuit components
Short-circuit current rating (SCCR) of industrial control panels
Reference Manual, 06/2013, A5E31896849002A/RS-AA/001 17
Example
The following example shows a circuit breaker according to UL489 in a feeder circuit and a
tested combination according to UL508 Type F. The circuit breaker has been tested and
approved for 100 kA and the self protected combination motor controller per UL 508 Type E
has also been tested and approved for 65 kA.
The combination shown below complies with 65 kA according to the UL rules.
Figure 4-8 Example combination

Basic steps for calculating the SCCR of a control panel
4.2 SB4.3 – Adaptation of the available short-circuit current rating based on the peak let-through currents when
using current-limiting devices in the feeder circuit
Short-circuit current rating (SCCR) of industrial control panels
18 Reference Manual, 06/2013, A5E31896849002A/RS-AA/001
4.2
SB4.3 – Adaptation of the available short-circuit current rating based
on the peak let-through currents when using current-limiting devices
in the feeder circuit
When short-circuit-current-limiting components are used in the feeder circuit, all components
in the branch circuit must be rated for the peak let-through current of the short-circuit-current-
limiting components used in the feeder circuit.
4.2.1
Current-limiting transformers
For branch circuits powered through a load transformer with an isolated secondary winding,
the following applies to the short-circuit current rating on the secondary side:
●Transformer < 10 kVA ⇒ max. 5 kA on the secondary side, i.e. all devices on the
secondary side must be rated for 5 kA or higher
●Transformer < 5 kVA and max. 120 V ⇒ max. 2 kA on the secondary side, i.e. all devices
on the secondary side must be rated for 2 kA or higher
●All other transformers are not current-limiting, i.e. they have the same short-circuit current
on the secondary and the primary side
4.2.2
Current-limiting circuit breakers (according to UL489)
To be able to use a circuit breaker in accordance with UL489 as a current-limiting
component in the feeder circuit, it must be marked "current limiting".
In this case, the let-through currents of the circuit breaker must be considered. The let-
through current can be obtained from the circuit breaker characteristic.
Example
The SCCR of the assembly is the breaking capacity of the circuit breaker in the feeder circuit
under the following conditions:
●The SCCR of all individual components in the branch circuit is not lower than the peak let-
through current of the circuit breaker in the feeder circuit.
●The breaking capacity of all branch circuit protective devices or the SCCR of all
combination motor controllers is not lower than the breaking capacity of the circuit
breaker in the feeder circuit.
⇒ The SCCR of the assembly is the lowest breaking capacity of a branch circuit protective
device or combination motor controller connected on the load side of the circuit breaker in
the feeder circuit if this is smaller than the breaking capacity of the circuit breaker in the
feeder circuit.
⇒ The SCCR of the assembly is the lowest SCCR of each branch circuit on the load side of
the circuit breaker if the above conditions do not apply.

Basic steps for calculating the SCCR of a control panel
4.2 SB4.3 – Adaptation of the available short-circuit current rating based on the peak let-through currents when
using current-limiting devices in the feeder circuit
Short-circuit current rating (SCCR) of industrial control panels
Reference Manual, 06/2013, A5E31896849002A/RS-AA/001 19
The selected circuit breaker lets 22
kA
through at a short
-circuit of 100 kA.
⇒ In other words
, all components in the
branch circuit must be designed for at
least 22
kA. The control panel is suitable
for a maximum let
-through value of
100
kA.

Basic steps for calculating the SCCR of a control panel
4.2 SB4.3 – Adaptation of the available short-circuit current rating based on the peak let-through currents when
using current-limiting devices in the feeder circuit
Short-circuit current rating (SCCR) of industrial control panels
20 Reference Manual, 06/2013, A5E31896849002A/RS-AA/001
4.2.3
Current-limiting fuses
Only fuses from UL508A, Tab. SB4.2 may be used as current-limiting fuses. This table
shows the relevant peak let-through currents (see column Ipx 10³).
Figure 4-9 Table SB4.2
The SCCR of the assembly is the breaking capacity of the fuse in the feeder circuit under the
following conditions:
●The SCCR of all individual components in the branch circuit is not lower than the peak let-
through current of the fuse in the feeder circuit.
●The breaking capacity of all branch circuit protective devices or the SCCR of all
combination motor controllers is not lower than the breaking capacity of the fuse in the
feeder circuit.
⇒ The SCCR of the assembly is the lowest breaking capacity of a branch circuit protective
device or combination motor controller connected on the load side of the fuse in the feeder
circuit if this is smaller than the breaking capacity of the fuse in the feeder circuit.
⇒ The SCCR of the assembly is the lowest SCCR of each branch circuit on the load side of
the fuse if the above conditions do not apply.