Siemens SITRANS F User manual

12/2014Edition
Answers for industry.
Operating Instructions
Ultrasonic Flowmeters
SITRANS 1010AERWDP Portable Flowmeter
SITRANS F

1010AERWDP
UNIFLOW UNIVERSAL
PORTABLE FLOWMETER
Field Manual A5E02617285 Rev AB
December 2014
For use with Operating System
Software Version 3.01.06F or later
This equipment contains components that are
susceptible to electrostatic discharge (ESD).
Please observe ESD control measures during
the handling and connection process.
Copyright©2014 Siemens Industry, Inc. All Rights Reserved Made in the USA
IMPORTANT NOTICE
Controlotron is now part of:
Siemens Industry, Inc.
Industry Automation Division
CoC Ultrasonic Flow
Hauppauge, NY 11788 USA

Manual Changes
NOTE: For the latest updates and revisions to this field manual go to:
http://support.automation.siemens.com/ and check the Product Manual listing.

MANUAL
ADDENDUM
Manual Addendum
September 2008
Copyright © 2008 Siemens Industry, Inc. All rights reserved Made in the USA
1010FMA-56
Operating System Software
Version Update

ManualAddendum 1010FMA-56
Operating System Software Version Update
INTRODUCTION
The following software operating system version update is for Version 3 flowmeters. Please refer to
this addendum when using this technical manual with Version 3 operating system software and
flowmeters that have been updated to Version 5.
Operating System Software Changes
1.The[MeterTypeMenu]includes a[Language]menuitemthat allowstheselectionof multiple flowmeter
menu foreign languages.
2. Version 3 and Version 5 Operating System Differences
The following table lists the differences between Version 3 and Version 5 operating system menu
items and menu hint lines.
A-1
Version 3 Version 5
Select Pipe Class Pick Pipe Class
Pick/Install Xdcr Install Xdcr
Data/Span/Set/Ca Span/Set/Cal
Strip ChartSetup Display Setup
DualChannelFlow 2 Channel Flow
DualBeam Flow Dual Path Flow
DataloggerSetup Logger Setup
TemperatureRange Temp Range
PipeConfiguration Pipe Config
DataloggerSetup Logger Setup
DataloggerMode Logger Mode
DataloggerData Logger Data
LogTimeInterval Logger Interval
DisplayDatalogger Display Logger
Recall Site Setup Recall Site
Delete Site Setup Delete Site
InstallCompleted? Install Complete
Estimated Vs m/s Estimated Vs M/S
Channel/Path Setup Channel Setup
ReflexorZeroFault/Set Zero Fault/Set
MemoryDelay (sec) Memory Delay s)
FlowVolume Units Flow Vol. Units
FlowDisplay Range Flow Disp. Range
Flow Display Scale Flow Disp. Scale
Total Volume Units Total Vol. Units
Batch/SampleTotal Batch/Sample Tot
CalibrateFlowrate Calib. Flowrate
AnalogInput Setup Analog Inp Setup
Flow Vel F/S Velocity F/S
Vs m/s Vs M/S
Valc % Valc
Vaer% Vaer
Vs Max m/s Vs Max M/S
(continued )

ManualAddendum 1010FMA-56
A-2
Vs Min m/s Vs Min M/S
Channel/PathSetup Chan/Path Setup
VfmaxGAL/MIN Vfmax
DateSite Created: Site Created:
Empty % Empty
AnalogOutput Trim Analog Out Trim
Pick flowtube size and type Select flowtube
and start operation
Empty Flowtube Set Empty Pipe Set
Version 3 Version 5
Gas Flowmeter Flow and VoS Unit Changes
1. Flowmeter Types
Flowmeterconfigurationsincludedwiththischangeinclude all SITRANS F Gas Flowmeters (7ME361*).
2. Flow Units
The table below describes the translation from the current gas flow units to the new gas flow units,
where only Cubic Feet and Cubic Meter volume units are affected. Also note that M = thousands and
MM = millions. Mass units and Velocity units remain unchanged.
Note: The flow legend changes depending upon the selection of Standard Volume enabled or
disabled.
FLOW UNITS
For STD VOLUME disabled For STD VOLUME enabled
Version3 Version 5 Version3 Version5
CUFT/SEC ACFS CUFT/SEC SCFS
CUFT/MIN ACFM CUFT/MIN SCFM
CUFT/HR ACFH CUFT/HR SCFH
CUFT/DAY ACFD CUFT/DAY SCFD
KCUFT/SEC MACFS KCUFT/SEC MSCFS
KCUFT/MIN MACFM KCUFT/MIN MSCFM
KCUFT/HR MACFH KCUFT/HR MSCFH
KCUFT/DAY MACFD KCUFT/DAY MSCFD
MCUFT/SEC MMACFS MCUFT/SEC MMSCFS
MCUFT/MIN MMACFM MCUFT/MIN MMSCFM
MCUFT/HR MMACFH MCUFT/HR MMSCFH
MCUFT/DAY MMACFD MCUFT/DAY MMSCFD
CUM/SEC M3/sec M/SEC NM3/sec
CUM/MIN M3/min CUM/MIN NM3/min
CUM/HR M3/hr CUM/HR NM3/hr
CUM/DAY M3/day CU M/DAY NM3/day
KCUM/SEC E3 M3/sec KCUM/SEC E3 NM3/sec
KCUM/MIN E3 M3/min KCU M/MIN E3NM3/min
KCUM/HR E3M3/hr KCU M/HR E3 NM3/hr
KCU M/DAY E3 M3/day KCUM/DAY E3NM3/day
MCUM/SEC E6 M3/sec MCUM/SEC E6 NM3/sec
MCUM/MIN E6 M3/min MCUM/MIN E6NM3/min
MCU M/HR E6 M3/hr MCUM/HR E6 NM3/hr
MCU M/DAY E6 M3/day MCU M/DAY E6NM3/day

ManualAddendum 1010FMA-56
4. Sound Velocity Units
Sound velocity will continue to be reported in units of meters/sec for metric units but will change to
Feet/sec for English unit selection. The flowmeter will display M/S and F/S to represent these two
variations.
Note: The units for Sound Velocity will be based on the [Preferred Units] menu item found in
the [Meter Facilities] menu and can not be changed unless a new site is created.
5. Transducer Model Menu Name
The following table lists the operating system menu item differences between Version 3 Hi Precision
and Version 5 Hi Precision transducer model names that appear on the [Install Xdcr] menu. Note that
T1, T2 and T3 indicate the different temperature ranges of the transducer.
3. Total Units
Total units are similar to flow units.
TOTALIZE UNITS
For STD VOLUME disabled
Version3 Version 5
CUFT ACF
KCUFT MACF
MCUFT MMACF
CUM M3
KCUM E3 M3
MCUM E6 M3
TOTALIZE UNITS
For STD VOLUME enabled
Version3 Version 5
CUFT SCF
KCUFT MSCF
MCUFT MMSCF
CUM NM3
KCUM E3 NM3
MCUM E6 NM3
A-3
Version 3 Transducers Version 5 Transducers
HiPrecision Hi Precision
1011HG HiPrec. 1011HP-T1
1011HP-T2
1011HP-T3