Siemens MMB3-ALD-UK User manual

P/N 315-050566-0
Installation Instructions
Model MMB3-ALD-UK
Upgrade Kit for ALD on MMB-3 Main Motherboard
4. Remove the old IC (U8) with the Extraction Tool
provided. Do this by lifting one end of the IC
slightly, then the other end. Continue this process
until the IC comes free.
5. Remove the new IC from the upgrade kit. Be
careful to avoid static discharge.
IMPORTANT
Place the new IC in the same pin location on
the socket as the one that was removed. If the
IC is installed incorrectly, severe damage to
the module can occur.
6. Gently place the new IC in the same pin location
on the socket as the one removed.
CAUTION
Be sure that the notched corner of U8 is
positioned correctly. Check that the IC is
properly seated in the sockets and that all
the IC pins are properly aligned with the
connectors.
7. Discard the old IC.
8. Re-install all connection to the MMB-3.
9. Re-install all power connections to the MMB-3.
10. Power up the system, AC first, then battery.
OPERATION
The Model MMB3-ALD-UK Upgrade Kit provides
the user with the materials to upgrade the ALD
firmware on the MMB-3 main motherboard.
INSTALLATION
To upgrade the MMB-3 with new ALD firmware,
remove the old U8 IC and replace it with the new
U8 (P/N 161-549335) following the steps listed
below.
1. Remove all connections to MMB-3, including
power and battery.
CAUTION
Remove all system power before
installation, first battery and then AC.
2. Locate the IC to be upgraded on the MMB-3.
(Refer to Figure 1.) The IC has a label attached
to the top surface that indicates the IC number
and the software revision currently installed.
Make certain that the IC number on the module
corresponds to the IC number in the
replacement kit.
3. Note where and how the IC is positioned on the
module. Refer to Figure 1 to note position of
notched corner on U8.
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada

P/N 315-050566-0
CB1
NAC1
P14P1
F2
BATTERY
20A
P2
BATTERY
MPS-6 MPS-12
F3
CZM-1 POWER
2 AMP
CB2
NAC2
10
11
12
CZM-1
POWER
1
P8
TB3
P3
POWER TO MOM-4
2 AMP MAX.
3
4
4
1
2LOOP 2
NAC 2
NAC 1
6
6
7
7
8
8
9
9
1
1
2
2
3
3
4
4
5
5
TO ANN
P13
MMB GND FAULT
DISCONNECT
TB2
LOOP 1
1
2
3
1
2
3
4
MNET
SPV
TRBL
TAMPER SWITCH
TB1
PROGRAMMER
P5
P17
1
P10
D2300CP/MOI-7 PRINTER
1
P4
MOM-4
P6
ALR
F1
MPS-6
8 AMP
F4
MOM-4
15 AMP
MMB-3
TB5
TB6
TB7
TB4
1
P18
P11
JP6JP5
S2
P9
1
S1
TB9
3
1
2
P20
TB8
4
3
2
1
XNET
ALD-2I
ALD-2I
F5 5V AUX
0.75 AMP
1
ALD GND FAULT
DISCONNECT
DS7
DS9
DS8
MMB GND FAULT
MNET
GND
FAULT
MNET
XMIT
P7
1
S4
3
S7
F6
BATTERY CHARGER
5 AMP
TB10
4
3
2
1
EXPANSION
JP7JP8
P18
JP3
JP1
JP2
JP4
DS5 DS6 UTILITY PORT
DS4
DS2
DS3
ALD GND FAULT
DS1
POLLING
P12
1
MNET GND FAULT
DISCONNECT
31
OFF ON
U8
U62
U80
LOCATION
OF U8
NOTCHED
CORNER
Figure 1
MMB-3 Board