Siemens SpeedStream 2105 User manual

SpeedStream® 2105
5-Port 10/100 Ethernet Switch
Quick-Start Guide
007-2105-001
Your SpeedStream®2105’s rear panel has five standard J-45 ports, plus a shared Uplink port. Each port
automatically detects the speed and duplex of the attached cabling to a network card, switch, hub, etc.
The ports operate in either full or half duplex mode.
Each port on your SpeedStream®2105 can connect to workstations, file servers, hubs, repeaters, bridges,
routers, or other switches. Connections to the 2105 require Category 5 UTP network cabling with J-45
connectors, not to exceed 328 ft (100 meters) in length.
Front Panel of 5-port Ethernet Switch ear Panel of 5-port Ethernet Switch
Cabling Guidelines
Use Category 5 UTP cabling with four pair of wires and J-45 connectors for all 100 Mbps connections.
Use the chart below to position your switches, hubs, and workstations.
F OM TO MAXIMUM DISTANCE
Switch Switch or Hub 328 ft (100 meters)
Switch or Hub Workstation 328 ft (100 meters)
LED Indicators
LED indicators are provided for monitoring various network conditions. A glance at the front panel
allows you to instantly monitor the status of each station port plus the overall condition of the switch.
LED LED STATUS INDICATION
PWR On Power indicator
FDX/COL On Full duplex transfer mode
Flashing Port has detected data collision error
Off Half duplex transfer mode
LINK/ACT
Yellow On 100 Mbps connection is detected
Flashing Data is sending/receiving at 100 Mbps
Green On 10 Mbps connection is detected
Flashing Data is sending/receiving at 10 Mbps
Step 2Hardware Description/Troubleshooting
45321
Link/ACT
COL/FDX
Yellow 100M
Green 10M
Power
12VDC 0.5A Uplink21345
For more information regarding SpeedStream® products visit: www.speedstream.com.
Efficient Networks, Inc.
A Siemens Company
4849 Alpha oad
Dallas, TX 75244
©2001 Efficient Networks, Inc. All rights reserved. Efficient Networks, its logos, "Live a Broadband Life" and SpeedStream are registered and unregis-
tered trademarks of Efficient Networks, Inc. Siemens and the Siemens logo are registered trademarks of Siemens AG, Germany. All other brand
names and trademarks are held by their respective companies. Efficient Networks reserves the right to make changes to product specifications at
any time without notice.
Technical Support for North America is available 24 hours a day, 7 days a week, by phone, email or online:
Phone: [phone]
Email: [email protected]
Online: http://www.support.speedstream.com

AC Power Adapter Extended Warranty and
Registration Card
Package Contents
Your package includes the following:
Before you begin: Step 1Hardware Installation
. Select an appropriate location.
2. Connect your workstation to any available RJ-45 port on the switch using twisted-
pair cable.
All end-node devices must be within 328 ft (100 meters) of the connected hub.
Using the hub in a stand-alone configuration you can network up to 5 workstations.
To connect a computer directly to the switch plug one end of the cable into the
switch then plug the other end of the cable into the computer’s network adapter.
3 Plug in the AC power adapter.
NOTE: Each time your SpeedStream® 2105 powers up, it will run a Diagnostic Self-
Test. After the test is complete, the Power LED will light up.
4. As connections to the 2 05's ports are made, each port’s corresponding
LINK/ACT will light up. The remaining LEDs will also light up according to how
your data is being transferred, e.g. full or half duplex, 0 Mbps or 00 Mbps.
5-Port 0/00Mbps
Fast Ethernet Switch
COL/FDX
POWER
LINK/ACT
45
3
2
Yellow 00M
Green 0M
2VDC 0.5A5432Uplink
RJ-45
Power
SpeedStream® 2 05 Ł
Ethernet Switch Ł
(5-port 0/ 00Base-T)
Safety and Certifications
Uplinking to other Switches and Hubs
NOTE: Using the Uplink port will automatically disable the port directly next to it
since the Uplink port is a shared port.
SpeedStream
®
Quick-Start Guide
5-Port Ethernet switch
10Mbps
Ethernet Switch Safety and Quick Start Guide
(5-port 0/ 00Base-T) Certifications
Information
JUST GO TO
www.speedstream.com/reg/extwrnty
GETAONEYEARHARDWAREWARRANTYEXTENSION
ONYOURSPEEDSTREAMPRODUCT.
GETA ONEYEARHARDWAREWARRANTYEXTENSION
ONYOURSPEEDSTREAMPRODUCT.
EXTENDED WARRANTY!
EXTENDED WARRANTY!
Keep this
near your PC to know where
to go for support, DSL education,
and new product info.
www.speedstream.com
Live a Broadband Life™
007-0105-002
This offer may be revoked, amended, supplemented, revised, altered, changed or terminated at any time without notice in the sole and absolute
discretion of Efficient Networks, Inc. This offer is available on select products only. This offer is available in select countries only. The offer is
good for thirty (30) days from the date of installation. Offer void where prohibited by law. Certain restrictions may apply.
' 2001 Efficient Networks, Inc. ASiemens Company
F EE
F EE

AC Power Adapter Extended Warranty and
Registration Card
Package Contents
Your package includes the following:
Before you begin: Step 1Hardware Installation
. Select an appropriate location.
2. Connect your workstation to any available RJ-45 port on the switch using twisted-
pair cable.
All end-node devices must be within 328 ft (100 meters) of the connected hub.
Using the hub in a stand-alone configuration you can network up to 5 workstations.
To connect a computer directly to the switch plug one end of the cable into the
switch then plug the other end of the cable into the computer’s network adapter.
3 Plug in the AC power adapter.
NOTE: Each time your SpeedStream® 2105 powers up, it will run a Diagnostic Self-
Test. After the test is complete, the Power LED will light up.
4. As connections to the 2 05's ports are made, each port’s corresponding
LINK/ACT will light up. The remaining LEDs will also light up according to how
your data is being transferred, e.g. full or half duplex, 0 Mbps or 00 Mbps.
5-Port 0/00Mbps
Fast Ethernet Switch
COL/FDX
POWER
LINK/ACT
45
3
2
Yellow 00M
Green 0M
2VDC 0.5A5432Uplink
RJ-45
Power
SpeedStream® 2 05 Ł
Ethernet Switch Ł
(5-port 0/ 00Base-T)
Safety and Certifications
Uplinking to other Switches and Hubs
NOTE: Using the Uplink port will automatically disable the port directly next to it
since the Uplink port is a shared port.
SpeedStream
®
Quick-Start Guide
5-Port Ethernet switch
10Mbps
Ethernet Switch Safety and Quick Start Guide
(5-port 0/ 00Base-T) Certifications
Information
JUST GO TO
www.speedstream.com/reg/extwrnty
GETAONEYEARHARDWAREWARRANTYEXTENSION
ONYOURSPEEDSTREAMPRODUCT.
GETA ONEYEARHARDWAREWARRANTYEXTENSION
ONYOURSPEEDSTREAMPRODUCT.
EXTENDED WARRANTY!
EXTENDED WARRANTY!
Keep this
near your PC to know where
to go for support, DSL education,
and new product info.
www.speedstream.com
Live a Broadband Life™
007-0105-002
This offer may be revoked, amended, supplemented, revised, altered, changed or terminated at any time without notice in the sole and absolute
discretion of Efficient Networks, Inc. This offer is available on select products only. This offer is available in select countries only. The offer is
good for thirty (30) days from the date of installation. Offer void where prohibited by law. Certain restrictions may apply.
' 2001 Efficient Networks, Inc. ASiemens Company
F EE
F EE

SpeedStream® 2105
5-Port 10/100 Ethernet Switch
Quick-Start Guide
007-2105-001
Your SpeedStream®2105’s rear panel has five standard J-45 ports, plus a shared Uplink port. Each port
automatically detects the speed and duplex of the attached cabling to a network card, switch, hub, etc.
The ports operate in either full or half duplex mode.
Each port on your SpeedStream®2105 can connect to workstations, file servers, hubs, repeaters, bridges,
routers, or other switches. Connections to the 2105 require Category 5 UTP network cabling with J-45
connectors, not to exceed 328 ft (100 meters) in length.
Front Panel of 5-port Ethernet Switch ear Panel of 5-port Ethernet Switch
Cabling Guidelines
Use Category 5 UTP cabling with four pair of wires and J-45 connectors for all 100 Mbps connections.
Use the chart below to position your switches, hubs, and workstations.
F OM TO MAXIMUM DISTANCE
Switch Switch or Hub 328 ft (100 meters)
Switch or Hub Workstation 328 ft (100 meters)
LED Indicators
LED indicators are provided for monitoring various network conditions. A glance at the front panel
allows you to instantly monitor the status of each station port plus the overall condition of the switch.
LED LED STATUS INDICATION
PWR On Power indicator
FDX/COL On Full duplex transfer mode
Flashing Port has detected data collision error
Off Half duplex transfer mode
LINK/ACT
Yellow On 100 Mbps connection is detected
Flashing Data is sending/receiving at 100 Mbps
Green On 10 Mbps connection is detected
Flashing Data is sending/receiving at 10 Mbps
Step 2Hardware Description/Troubleshooting
45321
Link/ACT
COL/FDX
Yellow 100M
Green 10M
Power
12VDC 0.5A Uplink21345
For more information regarding SpeedStream® products visit: www.speedstream.com.
Efficient Networks, Inc.
A Siemens Company
4849 Alpha oad
Dallas, TX 75244
©2001 Efficient Networks, Inc. All rights reserved. Efficient Networks, its logos, "Live a Broadband Life" and SpeedStream are registered and unregis-
tered trademarks of Efficient Networks, Inc. Siemens and the Siemens logo are registered trademarks of Siemens AG, Germany. All other brand
names and trademarks are held by their respective companies. Efficient Networks reserves the right to make changes to product specifications at
any time without notice.
Technical Support for North America is available 24 hours a day, 7 days a week, by phone, email or online:
Phone: [phone]
Email: [email protected]
Online: http://www.support.speedstream.com