Siemens SIMATIC NET SCALANCE W774-1 User manual

SIMATIC NET
Industrial Wireless LAN
SCALANCE W774
-1 /W734-1
Operating Instructions
SCALANCE W Mainstream (MSN)
07/2020
C79000
-G8976-C325-14
Introduction
1
Security
recommendations
2
Description of the device
3
Mounting
4
Connection
5
Upkeep and maintenance
6
Technical data
7
Dimension drawings
8
Approvals
9

Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C325-14
Ⓟ
07/2020 Subject to change
Copyright © Siemens AG 2013 - 2020
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to
prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a
safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices
shown below are graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger
will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning
relating to property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the
specific task in accordance with the relevant documentation, in particular its warning notices and safety
instructions. Qualified personnel are those who, based on their training and experience, are capable of
identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant
technical documentation. If products and components from other manufacturers are used, these must be
recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning,
operation and maintenance are required to ensure that the products operate safely and without any
problems. The permissible ambient conditions must be complied with. The information in the relevant
documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of
the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in
subsequent editions.

SCALANCE W774-1 /W734-1
Operating Instructions, 07/2020, C79000-G8976-C325-14 3
Table of contents
1 Introduction .................................................................................................................................................5
1.1 Information on the Operating Instructions.................................................................................... 5
2 Security recommendations .......................................................................................................................7
3 Description of the device........................................................................................................................ 13
3.1 Description of the device................................................................................................................ 13
3.2 Structure of the type designation ................................................................................................. 14
3.3 Components of the product ........................................................................................................... 15
3.4 Accessories ....................................................................................................................................... 15
3.4.1 Flexible connecting cables and antennas................................................................................... 18
3.4.1.1 Flexible connecting cables............................................................................................................. 18
3.4.1.2 Antennas............................................................................................................................................ 20
3.5 LED display........................................................................................................................................ 22
3.6 Reset button...................................................................................................................................... 24
4 Mounting................................................................................................................................................... 27
4.1 Wall mounting ................................................................................................................................... 28
4.2 Installing on an S7-300 standard rail........................................................................................... 30
4.3 Installing on an S7-1500 standard rail......................................................................................... 31
4.4 Installing on a DIN rail / removing................................................................................................ 32
5 Connection................................................................................................................................................ 35
5.1 Lightning protection, power supply and grounding................................................................... 36
5.2 Power supply..................................................................................................................................... 38
5.3 Ethernet.............................................................................................................................................. 41
5.4 Antenna connectors......................................................................................................................... 43
5.5 Replacing the PLUG (C-PLUG or KEY-PLUG)........................................................................... 45
5.6 Grounding .......................................................................................................................................... 48
6 Upkeep and maintenance....................................................................................................................... 49
6.1 Device configuration with PRESET-PLUG.................................................................................. 49
6.2 Restoring the factory settings ....................................................................................................... 51
6.3 Firmware update via WBM or CLI not possible ......................................................................... 52
7 Technical data.......................................................................................................................................... 55
7.1 Technical specifications W774/W734 RJ-45 .............................................................................. 55
7.2 Technical specifications W774 M12............................................................................................. 57

Table of contents
SCALANCE W774-1 /W734-1
4Operating Instructions, 07/2020, C79000-G8976-C325-14
8 Dimension drawings................................................................................................................................ 61
9 Approvals .................................................................................................................................................. 63
Index .......................................................................................................................................................... 65

SCALANCE W774-1 /W734-1
Operating Instructions, 07/2020, C79000-G8976-C325-14 5
Introduction
1
1.1 Information on the Operating Instructions
Validity of the Operating Instructions
These operating instructions cover the following products:
Product
Article number
Article number of
the US version
Article number of
the Israel version
Access points
SCALANCE W774-1 RJ-45
6GK5774-1FX00-0AA0
6GK5774-1FX00-0AB0
6GK5774-1FX00-0AC0
SCALANCE W774-1 M12 EEC
6GK5774-1FY00-0TA0
6GK5774-1FY00-0TB0
-
Ethernet client module
SCALANCE W734-1 RJ-45
6GK5734-1FX00-0AA0
6GK5734-1FX00-0AB0
-
These operating instructions apply to the following software version:
•SCALANCE W774/W734 with firmware as of version 6.5
Purpose of the Operating Instructions
Based on the operating instructions, you will be able to install and connect up the
SCALANCE W774/W734 correctly. The configuration and the integration of the device in
a WLAN are not described in these instructions.
Documentation on the accompanying DVD
You can find detailed information about configuration in the SCALANCE W700
configuration manuals on the accompanying DVD under the file name:
PH_SCALANCE-W770-W730-WBM_76.pdf and PH_SCALANCE-W770-W730-
CLI_76.pdf
Note
Make sure that you read the explanat
ions and instructions in the readme.htm file
Training, Service & Support
You will find information on Training, Service & Support in the multi--language document
"DC_support_99.pdf" on the data medium supplied with the documentation.

Introduction
1.1 Information on the Operating Instructions
SCALANCE W774-1 /W734-1
6Operating Instructions, 07/2020, C79000-G8976-C325-14
Security information
Siemens provides products and solutions with industrial security functions that support
the secure operation of plants, systems, machines and networks.
In order toprotect plants, systems, machines and networks against cyber threats, it is
necessary toimplement –and continuously maintain –aholistic, state-of-the-art
industrial security concept. Siemens’products and solutions constitute one element of
such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines andnetworks. Such systems, machines and components should only be
connected toan enterprise network orthe internet ifand tothe extent such a connection
is necessary and only when appropriate security measures (e.g. firewalls and/or network
segmentation) are in place.
For additional information on industrial security measures that may be implemented,
please visit https://www.siemens.com/industrialsecurity
Siemens’products and solutions undergo continuous development tomake them more
secure. Siemens strongly recommends that product updates are applied as soon as they
are available and that the latest product versions are used. Use ofproduct versions that
are no longer supported, and failure toapply the latest updates may increase customers’
exposure to cyber threats.
To stayinformed about product updates, subscribe totheSiemens Industrial Security
RSS Feed under https://www.siemens.com/industrialsecurity
Recycling and disposal
The products are low in pollutants, can be recycled and meet the requirements of the
WEEE directive 2012/19/EU for the disposal of electrical and electronic equipment.
Do not dispose of the products at public disposal sites.
For environmentally friendly recycling and the disposal of your old device contact a
certified disposal company for electronic scrap or your Siemens contact (Product return
(https://support.industry.siemens.com/cs/ww/en/view/109479891)).
Note the different national regulations.
Trademarks
The following and possibly other names not identified by the registered trademark sign ®
are registered trademarks of Siemens AG:
SIMATIC NET, SCALANCE, C-PLUG, RCoax

SCALANCE W774-1 /W734-1
Operating Instructions, 07/2020, C79000-G8976-C325-14 7
Security recommendations
2
To prevent unauthorized access, note the following security recommendations.
General
•You should make regular checks to make sure that the device meets these
recommendations and/or other security guidelines.
•Evaluate your plant as a whole in terms of security. Use a cell protection concept with
suitable products (https://www.industry.siemens.com/topics/global/en/industrial-
security/pages/default.aspx).
•When the internal and external network are disconnected, an attacker cannot access
internal data from the outside. Therefore operate the device only within a protected
network area.
•For communication via non-secure networks use additional devices with VPN
functionality to encrypt and authenticate the communication.
•Terminate management connections correctly (WBM. Telnet, SSH etc.).
Physical access
•Restrict physical access to the device to qualified personnel.
•The memory card or the PLUG (C-PLUG, KEY-PLUG, security PLUG) contains
sensitive data such as certificates, keys etc. that can be read out and modified.
Software (security functions)
•Keep the firmware up to date. Check regularly for security updates of the product.
You will find information on this on the Internet pages "Industrial Security
(https://www.siemens.com/industrialsecurity)".
•Inform yourself regularly about security advisories and bulletins published by Siemens
ProductCERT (https://www.siemens.com/cert/en/cert-security-advisories.htm).
•Only activate protocols that you really require to use the device.
•Use the security functions such as address translation with NAT (Network Address
Translation) or NAPT (Network Address Port Translation) to protect receiving ports
from access by third parties.
•Restrict access to the device with a firewall or rules in an access control list (ACL -
Access Control List).
•If RADIUS authentication is via remote access, make sure that the communication is
within the secured network area or is via a secure channel.
•The option of VLAN structuring provides good protection against DoS attacks and
unauthorized access. Check whether this is practical or useful in your environment.

Security recommendations
SCALANCE W774-1 /W734-1
8Operating Instructions, 07/2020, C79000-G8976-C325-14
•Use a central logging server to log changes and access operations. Operate your
logging server within the protected network area and check the logging information
regularly.
•Use WPA2/ WPA2-PSK with AES to protect the WLAN. If iPCF or iPCF-MC is used,
use the AES encryption.
Passwords
•Define rules for the assignment of passwords.
•Regularly change your passwords to increase security.
•Use passwords with a high password strength.
•Make sure that all passwords are protected and inaccessible to unauthorized
persons.
•A password must be changed if it is known or suspected to be known by unauthorized
persons.
•Do not use the same password for different users and systems.
Keys and certificates
•The device contains a pre-installed certificate with key. Replace this certificate with a
self-made certificate with key. We recommend that you use a certificate signed by a
reliable external or internal certification authority. You can install the certificate via
the WBM (System > Load and Save).
•Use the certification authority including key revocation and management to sign the
certificates.
•Ensure that user-defined private keys are protected and inaccessible to unauthorized
persons.
•Verify certificates and fingerprints on the server and client to prevent "man in the
middle" attacks.
•It is recommended that you use password-protected certificates in the PKCS#12
format.
•It is recommended that you use certificates with a key length of at least 2048 bits.
•Change keys and certificates immediately, if there is a suspicion of compromise.

Security recommendations
SCALANCE W774-1 /W734-1
Operating Instructions, 07/2020, C79000-G8976-C325-14 9
Secure/non-secure protocols and services
•Avoid and disable non-secure protocols, for example Telnet and TFTP. For historical
reasons, these protocols are still available, however not intended for secure
applications. Use non-secure protocols on the device with caution.
•Check whether use of the following protocols and services is necessary:
–Non-authenticated and unencrypted ports
–LLDP
–Syslog
–DHCP options 66/67
–TFTP
•The following protocols provide secure alternatives:
–SNMPv1/v2c →SNMPv3
Check whether use of SNMPv1/v2c is necessary. SNMPv1/v2c is classified as
non-secure. Use the option of preventing write access. The product provides you
with suitable setting options.
If SNMP is enabled, change the community names. If no unrestricted access is
necessary, restrict access with SNMP.
Use SNMPv3 in conjunction with passwords.
–HTTP →HTTPS
–Telnet →SSH
–TFTP →SFTP
•Use secure protocols when access to the device is not prevented by physical
protection measures.
•To prevent unauthorized access to the device or network, take suitable protective
measures against non-secure protocols.
•If you require non-secure protocols and services, operate the device only within a
protected network area.
•Restrict the services and protocols available to the outside to a minimum.
•For the DCP function, enable the "Read Only" mode after commissioning.

Security recommendations
SCALANCE W774-1 /W734-1
10 Operating Instructions, 07/2020, C79000-G8976-C325-14
List of available services
The following is a list of all available services and their ports through which the device
can be accessed.
The table includes the following columns:
•Service
The services that the device supports
•Default port status
This is the status of the port in the delivery state (factory setting).
•Configurable port/service
Indicates whether the port number or the service can be configured via WBM / CLI.
•Authentication
Specifies whether the communication partner is authenticated.
If optional, the authentication can be configured as required.
•Encryption
Specifies whether the transfer is encrypted.
If optional, the encryption can be configured as required.
Service Protocol/port
number
Default port
status
Configurable
Authentication Encryption
Port
Service
DHCP client
UDP/68
Outgoing only
--
✓
--
--
DHCP server
UDP/67
Closed
--
✓
--
--
DNS client
TCP/53
UDP/53
Outgoing only
--
✓
--
--
EthernetIP
TCP/44818,
UDP/2222
UDP/44818
Closed
--
✓
--
--
HTTP
TCP/80
Open
✓
✓
✓
--
HTTPS
TCP/443
Open
✓
✓
✓
✓
NTP Client
UDP/123
Outgoing only
✓
✓
--
--
PROFINET
UDP/34964
UDP/49154
UDP/49155
Open
--
✓
--
--
RADIUS
UDP/1812
Closed
✓
✓
✓
--
Remote Capture
TCP/2002
Closed
--
✓
--
--
SFTP client
TCP/22
Closed
✓
✓
✓
✓
SMTP client
TCP/25
Closed
✓
✓
--
--
SNMPv1/V2c
UDP/161
Open
✓
✓
--
--
SNMPv3
UDP/161
Open
✓
✓
Optional
Optional
SNMP traps
UDP/162
Outgoing only
--
✓
--
--
SNTP Client
UDP/123
Outgoing only
✓
✓
--
--
SSH
TCP/22
Open
✓
✓
✓
✓

Security recommendations
SCALANCE W774-1 /W734-1
Operating Instructions, 07/2020, C79000-G8976-C325-14 11
Service Protocol/port
number
Default port
status
Configurable
Authentication Encryption
Port
Service
Syslog Client
UDP/514
Closed
✓
✓
--
--
Syslog (secure) Client
TCP/6514
Closed
✓
✓
--
✓
Telnet
TCP/23
Open
✓
✓
✓
--
TFTP client
UDP/69
Closed
✓
✓
--
--
DCP
--
Open
--
✓
--
--
LLDP
--
Open
--
✓
--
--
RSTP
--
Open
--
✓
--
--
iPRP
--
Open
--
✓
--
--
MSTP
--
Closed
--
✓
--
--
IPv6
--
Closed
--
✓
--
--
SIMATIC NET TIME
--
Closed
--
✓
--
--

Security recommendations
SCALANCE W774-1 /W734-1
12 Operating Instructions, 07/2020, C79000-G8976-C325-14

SCALANCE W774-1 /W734-1
Operating Instructions, 07/2020, C79000-G8976-C325-14 13
Description of the device
3
3.1 Description of the device
SCALANCE W774-1 /W734-1 RJ45
①
Antenna connector R1A1
②
PLUG slot / RESET button
③
Antenna connector R1A2
④
LEDs
⑤
Ethernet connector P2 (PoE capability)
⑥
Ethernet connector P1
⑦
Connector for power supply (L1, L2)
⑧
Eye for grounding (diameter 4.5 mm) / wall mounting
Figure 3-1 Device description of the RJ-45 variant

Description of the device
3.2 Structure of the type designation
SCALANCE W774-1 /W734-1
14 Operating Instructions, 07/2020, C79000-G8976-C325-14
SCALANCE W774-1 /W734-1 M12
①
Antenna connector R1A1
②
PLUG slot / RESET button
③
Antenna connector R1A2
④
LEDs
⑤
Ethernet connector P2 (PoE capability)
⑥
Ethernet connector P1
⑦
Connector for power supply (L1, L2)
⑧
Eye for grounding (diameter 4.5 mm) / wall mounting
Figure 3-2 Device description of the M12 variant
3.2 Structure of the type designation
The type designation of the device is made up of several parts that have the following
meaning:

Description of the device
3.3 Components of the product
SCALANCE W774-1 /W734-1
Operating Instructions, 07/2020, C79000-G8976-C325-14 15
3.3 Components of the product
The following components are supplied with the product:
•SCALANCE W774 or SCALANCE W734
•2 protective caps for the antenna sockets
•Only with device variant M12
–3 protective caps for the M12 sockets
•Only with device variant RJ-45:
–4-pin terminal block for the power supply
•1 screw for mounting on an S7-300 standard rail or S7-1500 standard rail
•SIMATIC NET Industrial Wireless LAN CD
Please check that the consignment you have received is complete. If the consignment is
incomplete, contact your supplier or your local Siemens office.
3.4 Accessories
PLUG
Component
Description
Article number
C-PLUG
Configuration PLUG
Exchangeable storage medium for configuration
data.
256 MB
6GK1900-0AB10
KEY-PLUG
features
Enabling of iFeatures and exchangeable storage
medium for storage of configuration data
KEY-PLUG W780 iFeatures AP
6GK5907-8PA00
KEY-PLUG W740 iFeatures Client
6GK5907-4PA00
KEY-PLUG
W700 Security
W700 Security
Enabling of “Inter AP Blocking” and exchangeable
storage medium for storage of configuration data
6GK5907-0PA00
Technical data subject to change.
You will find further information on the range of accessories in the Industry Mall
(https://mall.industry.siemens.com)

Description of the device
3.4 Accessories
SCALANCE W774-1 /W734-1
16 Operating Instructions, 07/2020, C79000-G8976-C325-14
M12 data plug-in connector
Component
Description
Article number
IE FC M12
PLUG PRO
2x2
M12 data plug-in connector for IE
FC TP cables 2x2, IP65/67, D-
coded, axial cable outlet
1 connector per
package
6GK1901-0DB20-6AA0
8 connectors per
package
6GK1901-0DB20-6AA8
Cables Industrial Ethernet
Component
Description
Article number
IE FC TP STANDARD
CABLE GP2X2
(PROFINET type A)
Standard bus cable, TP installation cable
for connection to FC OUTLET RJ-45, for
universal use, 4-wire, shielded, CAT 5E
Sold by the meter
6XV1840-2AH10
IE FC TP ROBUST
STANDARD CABLE GP
2X2
(PROFINET type A)
Standard bus cable, ATPE outer jacket for
connection to FC RJ-45 PLUG and FC
OUTLET RJ-45, fixed installation, for uni-
versal use, 4-wire, shielded, CAT 5
Sold by the meter
6XV1841-2A
IE FC TP ROBUST
FLEXIBLE CABLE GP 2X2
(PROFINET type B)
Flexible bus cable, TPE outer jacket for
connection to FC RJ-45 PLUG and FC
OUTLET RJ-45, flexible wires, 4-wire,
shielded, CAT 5
Sold by the meter
6XV1841-2B
IE FC TP FLEXIBLE
CABLE GP 2X2
(PROFINET type B)
Flexible bus cable, TP installation cable,
flexible wires, shielded, CAT 5
Sold by the meter
6XV1870-2B
IE FC TP TRAILING
CABLE 2X2
(PROFINET type C)
Highly flexible bus cable, TP installation
cable for connection to FC OUTLET RJ-45,
for use in drag chains, 4-wire, shielded,
CAT 5
Sold by the meter
6XV1840-3AH10
IE TP TORSION CABLE
2X2
(PROFINET type C)
Highly flexible bus cable, TP installation
cable for use in highly flexible applications
(torsion), 4-wire
Sold by the meter
6XV1870-2F
IE CONNECTING CABLE
M12-180/IE RJ45
Flexible IE connecting cable, 4-wire, preas-
sembled with a 4-pin M12 plug (D-coded)
and an IE FC RJ-45 plug 145
6XV1871-5T*
IE CONNECTING CABLE
M12-180/M12-180
Flexible IE connecting cable, 4-wire, preas-
sembled with two 4-pin M12 plugs (D-
coded)
6XV1870-8A*
* Available in different lengths

Description of the device
3.4 Accessories
SCALANCE W774-1 /W734-1
Operating Instructions, 07/2020, C79000-G8976-C325-14 17
Cabinet feedthrough
Component
Description
Article number
IE M12 PANEL
FEEDTHROUGH
Cabinet feedthrough for conversion from M12
connector technology (D-coded, IP65) to RJ-45
connector technology (IP20)
pack of 5
6GK1901-0DM20-2AA5
IE M12 PANEL
FEEDTHROUGH
PRO
Cabinet feedthrough for conversion from M12
connector technology (D-coded, IP65) to M12
connector technology (D-coded, IP65)
pack of 5
6GK1901-0DM30-2AA5
IE M12 PANEL
FEEDTHROUGH
4X2
Cabinet feedthrough for conversion from M12
connector technology (X-coded, IP65/67) to RJ-45
connector technology (X-coded, IP20)
pack of 5
6GK1901-0DM40-2AA5
N-Connect/N-
Connect fe-
male/female
Panel Feed-
through
Panel feedthrough for wall thicknesses up to a
maximum of 4.5 mm, two N-Connect female con-
nectors.
6GK5798-2PP00-2AA6
N-
Connect/SMA-
Connect fe-
male/female
Panel Feed-
through
Panel feedthrough for wall thicknesses up to a
maximum of 5.5 mm, two N-Connect/SMA female
connectors.
6GK5798-0PT00-2AA6
Energy cable
Component
Description
Article number
Energy cable
2 x 0.75
Energy cable for connection of signaling contact
and power supply 24 VDC, stranded wire 2 x 0.75
mm2, trailing type, not assembled
Sold by the meter
6XV1812-8A
Robust Energy
Cable 4 x 0.75
Energy cable for connection of power supply 24
VDC, 4-wire stranded 4 x 0.75 mm2, robust, flexi-
ble, not assembled
Sold by the meter
6XV1801-2A
M12 PLUG-IN
CABLE
Flexible plug-in power cable to connect the power
supply 24 VDC, 4-wire, preassembled with a 4-pin
M12 plug and an M12 socket (A-coded)
6XV1801-5D*
* Available in different lengths

Description of the device
3.4 Accessories
SCALANCE W774-1 /W734-1
18 Operating Instructions, 07/2020, C79000-G8976-C325-14
Socket
Component
Description
Article number
IE POWER
M12 CABLE
CONNECTOR
PRO
Socket for the 24 VDC power supply. 4-pin, A-coded
pack of 3
6GK1907-0DC10-6AA3
Lightning protection
Component
Description
Article number
LP798-1N
Lighting protector with N/N female/female connect-
or with gas discharge technology
6GK5798-2LP00-2AA6
LP798-2N
Lighting protector with N/N female/female connect-
or with quarter wave technology
6GK5798-2LP10-2AA6
Terminating resistor
Component
Description
Article number
TI795-1N
Electrical connection
N-Connect, male
Pack of 1
6GK5795-1TN00-1AA0
3.4.1 Flexible connecting cables and antennas
3.4.1.1 Flexible connecting cables
Flexible connecting cable N-Connect/R-SMA
Flexible connecting cable for connecting an antenna to a SCALANCE W device with R-
SMA connectors, preassembled with a connector N-male and R-SMA male
Length
Article number
0.3 m
6XV1875-5CE30
1 m
6XV1875-5CH10
2 m
6XV1875-5CH20
5 m
6XV1875-5CH50
10 m
6XV1875-5CN10

Description of the device
3.4 Accessories
SCALANCE W774-1 /W734-1
Operating Instructions, 07/2020, C79000-G8976-C325-14 19
For railway applications, the following connecting cable are available:
Length
Article number
1 m
6XV1875-5TH10
2 m
6XV1875-5TH20
5 m
6XV1875-5TH50
Flexible connecting cable N-Connect/N-Connect
Flexible connecting cable for connecting an antenna to a SCALANCE W device with N-
Connect connectors.
Preassembled with two N male connectors:
Length
Article number
1 m
6XV1875-5AH10
2 m
6XV1875-5AH20
5 m
6XV1875-5AH50
10 m
6XV1875-5AN10
For railway applications, the following connecting cable are available:
Length
Article number
1 m
6XV1875-5SH10
2 m
6XV1875-5SH20
5 m
6XV1875-5SH50
Flexible connecting cable IWLAN QMA/N-Connect male/female
Adapter cable for connecting a MIMO antenna with QMA connectors with the flexible
connecting cables. Preassembled with two connectors QMA male and N-Connect
female. pack of 3
Length
Article number
1 m
6XV1875-5JH10
For railway applications, the following connecting cable is available Note: Scope of
delivery: Pack of 1
Length
Article number
1 m
6XV1875-5VH10

Description of the device
3.4 Accessories
SCALANCE W774-1 /W734-1
20 Operating Instructions, 07/2020, C79000-G8976-C325-14
3.4.1.2 Antennas
Note
When you select an antenna, keep in
mind the national approvals for your device.
You will find more detailed information in Wireless approvals
(
https://www.siemens.com/wireless-approvals).
The SCALANCE W1788-2IA uses internal omni antennas (3/4 dBi at 2.4 GHz or 5 GHz).
Type
Properties
Article number
IWLAN RCoax Antenna
ANT792-4DN
RCoax helical antenna with circular polari-
zation for RCoax systems, 4 Bi, 2.4 GHz,
IP65, N-Connector female.
6GK5792-4DN00-0AA6
ANT792-6MN
Omnidirectional antenna, mast/wall
mounting, 6 dBi 2.4 GHz, IP67, N-Connect
female
6GK5792-6MN00-0AA6
ANT792-8DN
Directional antenna, mast/wall mounting,
14 dBi 2.4 GHz, IP32, N-Connect female
6GK5792-8DN00-0AA6
IWLAN RCoax
ANT793-4MN
RCoax λ4 antenna with vertical polariza-
tion for RCoax systems, 6 dBi, 5 GHz, IP65,
N-Connector female
6GK5793-4MN00-0AA6
ANT793-6DG
Wide angle antenna, mast/wall mounting,
9 dBi 5 GHz, IP66/67, 2 x N-Connect fe-
male
6GK5793-6DG00-0AA0
ANT793-8DJ
Directional antenna, mast/wall mounting,
18 dBi 5 GHz, IP67, 2 x N-Connect female
6GK5793-8DJ00-0AA0
ANT793-8DK
Directional antenna, mast/wall mounting,
23 dBi 5 GHz, 2 x N-Connect female
6GK5793-8DK00-0AA0
ANT793-8DL
Directional antenna vertical-horizontal
polarized, 5 GHz, 14dBi, IP66, 2xN-
Connect female
6GK5793-8DL00-0AA0
ANT793-8DP
Directional antenna, mast/wall mounting,
13 / 13.5 dBi 4.9 GHz and 5 GHz, N-
Connect female
This antenna is not available in Korea
6GK5793-8DP00-0AA0
ANT795-4MA
Omnidirectional antenna, directly on the
device, 3/5 dBi 2.4 GHz and 5 GHz, IP30,
R-SMA connector male for direct installa-
tion on the device, angle connector ad-
justable 0° - 180°.
6GK5795-4MA00-0AA3
ANT795-4MB
Omnidirectional antenna, 2/3 dBi 2.4 GHz
and 5 GHz, IP30, R-SMA connector female
for direct mounting on the device, angle
connector adjustable 0° to 90°.
6GK5795-4MB00-0Ax0
ANT795-4MC
Omnidirectional antenna, 3/5 dBi, 2.4 GHz
and 5 GHz, IP65, N-Connect male for di-
rect installation on the device, straight
connector.
6GK5795-4MC00-0AA3