Sierra Wireless AirPrime SL6087 User manual

WA_DEV_SL6087_PTS_002
001
Jun 17, 2010
AirPrime SL6087
AirPrime SL6087 User Guide

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 2
AirPrime SL6087 User Guide
Important Notice
Due to the nature of wireless communications, transmission and reception of data can never be
guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant
delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used
in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used
in situations where failure to transmit or receive data could result in damage of any kind to the user or
any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless
accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or
received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or
receive such data.
Safety and Hazards
Do not operate the Sierra Wireless modem in areas where blasting is in progress, where explosive
atmospheres may be present, near medical equipment, near life support equipment, or any equipment
which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless modem
MUST BE POWERED OFF. The Sierra Wireless modem can transmit signals that could interfere with
this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on
the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When
operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard
systems.
Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is
open. Sierra Wireless modems may be used at this time.
The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of
a vehicle. Doing so will detract from the driver or operator’s control and operation of that vehicle. In
some states and provinces, operating such communications devices while in control of a vehicle is an
offence.
Limitations of Liability
This manual is provided “as is”. Sierra Wireless makes no warranties of any kind, either expressed or
implied, including any implied warranties of merchantability, fitness for a particular purpose, or
noninfringement. The recipient of the manual shall endorse all risks arising from its use.
The information in this manual is subject to change without notice and does not represent a
commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES
SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL,
GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING,
BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR
REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS
PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY
THIRD PARTY.
Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability
arising under or in connection with the Sierra Wireless product, regardless of the number of events,
occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the
Sierra Wireless product.

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 3
AirPrime SL6087 User Guide
Patents
Portions of this product may be covered by some or all of the following US patents:
5,515,013
5,629,960
5,845,216
5,847,553
5,878,234
5,890,057
5,929,815
6,169,884
6,191,741
6,199,168
6,339,405
6,359,591
6,400,336
6,516,204
6,561,851
6,643,501
6,653,979
6,697,030
6,785,830
6,845,249
6,847,830
6,876,697
6,879,585
6,886,049
6,968,171
6,985,757
7,023,878
7,053,843
7,106,569
7,145,267
7,200,512
7,295,171
7,287,162
D442,170
D459,303
D599,256
D560,911
and other patents pending.
This product includes technology licensed from QUALCOMM®3G
Manufactured or sold by Sierra Wireless or its licensees under one or more patents licensed from
InterDigital Group
Copyright
© 2010 Sierra Wireless. All rights reserved.
Trademarks
AirCard®and Watcher®are registered trademarks of Sierra Wireless. Sierra Wireless™, AirPrime™,
AirLink™, AirVantage™and the Sierra Wireless logo are trademarks of Sierra Wireless.
, , ®, inSIM®, WAVECOM®, WISMO®, Wireless Microprocessor®,
Wireless CPU®, Open AT®are filed or registered trademarks of Sierra Wireless S.A. in France and/or
in other countries.
Windows®and Windows Vista®are registered trademarks of Microsoft Corporation.
Macintosh and Mac OS are registered trademarks of Apple Inc., registered in the U.S. and other
countries.
QUALCOMM®is a registered trademark of QUALCOMM Incorporated. Used under license.
Other trademarks are the property of the respective owners.
Contact Information
Sales Desk:
Phone:
1-604-232-1488
Hours:
8:00 AM to 5:00 PM Pacific Time
E-mail:
[email protected]om
Post:
Sierra Wireless
13811 Wireless Way
Richmond, BC
Canada V6V 3A4
Fax:
1-604-231-1109
Web:
www.sierrawireless.com
Consult our website for up-to-date product descriptions, documentation, application notes, firmware
upgrades, troubleshooting tips, and press releases: www.sierrawireless.com

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 4
AirPrime SL6087 User Guide
Document History
Version
Date
Updates
001
May 18, 2010
Creation

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 5
Contents
1. INTRODUCTION ..................................................................................................9
1.1. Physical Dimensions .........................................................................................................9
1.2. GSM/GPRS/EGPRS Features..........................................................................................9
1.3. Interfaces...........................................................................................................................9
1.4. Operating System..............................................................................................................9
1.5. Connection Interfaces .....................................................................................................10
1.6. Environment and Mechanics...........................................................................................10
1.6.1. RoHS Directive Compliant .......................................................................................10
1.6.2. Disposing of the Product..........................................................................................10
2. FUNCTIONAL SPECIFICATIONS......................................................................11
2.1. Functional Architecture....................................................................................................11
2.1.1. RF Functionalities ....................................................................................................11
2.2. Operating System............................................................................................................11
3. TECHNICAL SPECIFICATIONS........................................................................12
3.1. Power Supply ..................................................................................................................12
3.2. Mechanical Specifications...............................................................................................12
4. INTERFACES.....................................................................................................15
4.1.1. Pin Description.........................................................................................................15
4.2. RF Interface.....................................................................................................................19
4.2.1. RF Connections .......................................................................................................19
4.2.2. Antenna Specifications.............................................................................................19
5. CERTIFICATION COMPLIANCE AND RECOMMENDED STANDARDS .........20
5.1. Certification Compliance .................................................................................................20
5.2. Applicable Standards Listing...........................................................................................20
6. REFERENCES ...................................................................................................22
6.1. Web Site Support ............................................................................................................22
6.2. Reference Documents.....................................................................................................22
6.2.1. Sierra Wireless Software Documentation................................................................22
6.2.2. Firmware Documentation.........................................................................................23
6.2.3. Hardware Documentation ........................................................................................23
6.2.4. Other Sierra Wireless Documentation .....................................................................24
6.2.5. Other Related Documentation .................................................................................24
6.2.6. Application Notes .....................................................................................................24
6.3. List of Abbreviations........................................................................................................25
7. SAFETY RECOMMENDATIONS (FOR INFORMATION ONLY) .......................28
7.1. RF Safety.........................................................................................................................28
7.1.1. General.....................................................................................................................28

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 6
AirPrime SL6087 User Guide
7.1.2. Exposure to RF Energy............................................................................................28
7.1.3. Efficient Terminal Operation.....................................................................................28
7.1.4. Antenna Care and Replacement..............................................................................28
7.2. General Safety.................................................................................................................29
7.2.1. Driving......................................................................................................................29
7.2.2. Electronic Devices....................................................................................................29
7.2.3. Vehicle Electronic Equipment ..................................................................................29
7.2.4. Medical Electronic Equipment..................................................................................29
7.2.5. Aircraft......................................................................................................................29
7.2.6. Children....................................................................................................................30
7.2.7. Blasting Areas..........................................................................................................30
7.2.8. Potentially Explosive Atmospheres..........................................................................30

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 7
List of Figures
Figure 1. Functional Architecture....................................................................................................11
Figure 2. SL6087 Embedded Module Mechanical Drawing...........................................................13
Figure 3. LGA Pin Dimension and Location ...................................................................................14

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 8
List of Tables
Table 1: List of RF Frequency Ranges..........................................................................................11
Table 2: Input Power Supply Voltage............................................................................................12
Table 3: LGA Pads Description.....................................................................................................15
Table 4: Antenna Specifications....................................................................................................19
Table 5: Standards Conformity for the SL6087 Embedded Module .............................................20
Table 6: Applicable Standards and Requirements for the SL6087 Embedded Module................20

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 9
1. Introduction
The AirPrime SL6087 Intelligent Embedded Module is a self-contained GSM850/PCS-GPRS/EGPRS
850/1900 dual-band embedded module.
1.1. Physical Dimensions
Length: 30.0mm
Width: 25.0mm
Thickness: 2.65mm (excluding label thickness)
Weight: 3.8g
1.2. GSM/GPRS/EGPRS Features
2-Watt EGSM –GPRS 850 radio section running under 3.6 volts
1-Watt GSM –GPRS 1900 radio section running under 3.6 volts
0.5-Watt EGPRS 850 radio section running under 3.6 volts
0.4-Watt EGPRS 1900 radio section running under 3.6 volts
Hardware GSM/GPRS class 10 and EGPRS class 10 capable
1.3. Interfaces
Digital section running under 2.8V and 1.8V
3V/1V8 SIM interface
Complete Interfacing:
Power supply
Serial link
Analog audio
PCM digital audio
SIM card
USB 2.0 slave
Serial LCD (not available with AT commands)
1.4. Operating System
Real Time Clock (RTC) with calendar
Battery charger
Echo cancellation + noise reduction (quadri codec)
Full GSM or GSM/GPRS/EGPRS Operating System stack

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 10
AirPrime SL6087 User Guide
Introduction
1.5. Connection Interfaces
The SL6087 Embedded Module has a 74-solderable pad LGA form factor that includes:
One RF connection pad (antenna connection)
Baseband signals connection
1.6. Environment and Mechanics
1.6.1. RoHS Directive Compliant
The AirPrime SL6087 Embedded Module is compliant with RoHS Directive
2002/95/EC which sets limits for the use of certain restricted hazardous substances.
This directive states that “from 1st July 2006, new electrical and electronic equipment
put on the market does not contain lead, mercury, cadmium, hexavalent chromium,
polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE)”.
1.6.2. Disposing of the Product
This electronic product is subject to the EU Directive 2002/96/EC for Waste Electrical
and Electronic Equipment (WEEE). As such, this product must not be disposed off at
a municipal waste collection point. Please refer to local regulations for directions on
how to dispose of this product in an environmental friendly manner.

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 11
2. Functional Specifications
2.1. Functional Architecture
2.1.1. RF Functionalities
The Radio Frequency (RF) functionalities of the AirPrime SL6087 Embedded Module comply with the
Phase II GSM 850/PCS 1900 recommendations. The frequency range for the transmit band and
receive band are given in the table below.
Table 1: List of RF Frequency Ranges
RF Bandwidth
Transmit Band (Tx)
Receive Band (Rx)
GSM 850
824 to 849 MHz
869 to 894 MHz
PCS 1900
1850 to 1910 MHz
1930 to 1990 MHz
The Radio Frequency (RF) component is based on a specific quad-band chip that includes the
following:
Quad-band LNAs (Low Noise Amplifier)
Direct Conversion Receiver
Offset PLL/PL (Phase Locked Loop and Polar Loop) transmitter
Frequency synthesizer
Digitally controlled crystal oscillator (DCXO)
Tx/Rx FEM ( Front-End module) for quad-band GSM/GPRS/EGPRS
2.2. Operating System
The AirPrime SL6087 Embedded Module is Sierra Wireless Software Suite compliant. With the Sierra
Wireless Software Suite and the AirPrime SL6087 Embedded Module, customers can embed their
own applications with the AirPrime SL6087 and turn the AirPrime SL6087 embedded module into a
solution for their specific market need.
The operating system allows for the AirPrime SL6087 Embedded Module to be controlled by AT
commands. However, some interfaces in the AirPrime SL6087 Embedded Module may still not be
available even with AT command control as these interfaces are dependent on the peripheral devices
connected to the AirPrime SL6087 Embedded Module.

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 12
3. Technical Specifications
3.1. Power Supply
The following table describes the electrical characteristics of the input power supply voltage that will
guarantee nominal functioning of the AirPrime SL6087 Embedded Module.
Table 2: Input Power Supply Voltage
VMIN
VNOM
VMAX
Ripple Max (Uripp)
Ipeak Max
VBATT
3.2V1,2
3.6V
4.8V
250mVpp (freq < 10kHz)
40mVpp (10kHz < freq <
100kHz)
5mVpp (freq > 100kHz)
(TBC)
2.0A
1: This value must be guaranteed during the burst (with 2.0A Peak in GSM, GPRS or EGPRS mode)
2: Maximum operating Voltage Standing Wave Ratio (VSWR) 2:1.
3.2. Mechanical Specifications
The AirPrime SL6087 Embedded Module has a nearly-complete self-contained shield. The
mechanical specifications are shown in the figures below, including the area needed for the AirPrime
SL6087 Embedded Module to fit in an application.

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 13
AirPrime SL6087 User Guide
Technical Specifications
Figure 1. SL6087 Embedded Module Mechanical Drawing

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 14
AirPrime SL6087 User Guide
Technical Specifications
Figure 2. LGA Pin Dimension and Location

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 15
4. Interfaces
4.1.1. Pin Description
Refer to the following table for the LGA pads description.
Table 3: LGA Pads Description
Pin #
Signal Name
I/O Type
Voltage
I/O*
Reset State
Description
Dealing with Unused Pins
Nominal
Mux
1
CT104-RXD1
GPIO5
VCC_2V8
O
1
Main RS232 Receive
(RXD1) Add a test point for
firmware update
2
~CT106-CTS1
GPIO7
VCC_2V8
O
Z
Main RS232 Clear To Send
(CTS1) Add a test point for
firmware update
3
BAT-RTC
BAT-RTC
I/O
RTC Battery connection
NC
4
GPIO0
32kHz
VCC_2V8
I/O
32 kHz
NC
5
AUX-ADC
Analog
I
Analog to Digital Input
Pull to GND
6
SIM-VCC
1V8 or 3V
O
SIM Power Supply
7
~SIM-RST
1V8 or 3V
O
0
SIM reset Output
8
SIM-IO
1V8 or 3V
I/O
Pull-up (about
10kΩ)
SIM Data
9
SIM-CLK
1V8 or 3V
O
0
SIM Clock
10
SIMPRES
GPIO18
VCC_1V8
I
Z
SIM Detection
NC
11
~SPI1-I_CS
GPIO20
VCC_2V8
I/O
Z
SPI1 Chip Select
NC
12
SPI1-CLK
GPIO12
VCC_2V8
O
Z
SPI1 Clock
NC
13
SPI1-IO
GPIO13
VCC_2V8
I/O
Z
SPI1 Data Input / Output
NC
14
SPI1-I
GPIO19
VCC_2V8
I
Z
SPI1 Data Input
NC
15
GPIO21
VCC_2V8
I/O
Undefined
NC

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 16
AirPrime SL6087 User Guide
Interfaces
Pin #
Signal Name
I/O Type
Voltage
I/O*
Reset State
Description
Dealing with Unused Pins
Nominal
Mux
16
SDA
GPIO2
Open Drain
I/O
Z
I²C Data
NC
17
SCL
GPIO1
Open Drain
O
Z
I²C Clock
NC
18
BOOT
VCC_1V8
I
Not Used
Add a test point / a jumper/ a
switch to VCC_1V8 (Pin 5) in case
Download Specific mode is used
(See product specification for
details)
19
Reserved_19
20
Reserved_20
21
GND
22
ANT
23
GND
24
NC
25
GND
26
NC
27
NC
28
GND
29
NC
30
GND
31
Reserved_31
32
Reserved_32
33
Reserved_33
34
Reserved_34
35
Reserved_35
36
Reserved_36
37
GPIO24
VCC_2V8
I/O
Z
NC
38
GPIO22
VCC_2V8
I/O
Z
NC

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 17
AirPrime SL6087 User Guide
Interfaces
Pin #
Signal Name
I/O Type
Voltage
I/O*
Reset State
Description
Dealing with Unused Pins
Nominal
Mux
39
GPIO23
VCC_2V8
I/O
Z
NC
40
ADC1/BAT-
TEMP
Analog
I
Analog temperature
Pull to GND
41
CHG-IN
CHG-IN
I
Charger input
NC
42
ADC0/VBATT
VBATT
I
Power Supply
43
ON/~OFF
VBATT
I
ON / ~OFF Control
44
ADC0/VBATT
VBATT
I
Power Supply
45
CT103-TXD2
GPIO14
VCC_1V8
I
Z
Auxiliary RS232 Transmit
(TXD2) Pull-up to VCC_1V8 with
100kΩ and add a test point for
debugging
46
CT104-RXD2
GPIO15
VCC_1V8
O
Z
Auxiliary RS232 Receive
Add a test point for debugging
47
~CT106-CTS2
GPIO16
VCC_1V8
O
Z
Auxiliary RS232 Clear To
Send
(CTS2) Add a test point for
debugging
48
~CT105-RTS2
GPIO17
VCC_1V8
I
Z
Auxiliary RS232 Request
To Send
(RTS2) Pull-up to VCC_1V8 with
100kΩ and add a test point for
debugging
49
VPAD-USB
VPAD-USB
I
USB Power supply input
NC
50
USB-DP
VPAD-USB
I/O
USB Data
NC
51
USB-DM
VPAD-USB
I/O
USB Data
NC
52
GND
53
MICP
Analog
I
Microphone Input Positive
NC
54
MICN
Analog
I
Microphone Input Negative
NC
55
Reserved_55
56
SPKN
Analog
O
Speaker Output Negative
NC
57
SPKP
Analog
O
Speaker Output Positive
NC
58
VCC_2V8
VCC_2V8
O
2.8V Supply Output
NC
59
VCC_1V8
VCC_1V8
O
1.8V Supply Output
NC

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 18
AirPrime SL6087 User Guide
Interfaces
Pin #
Signal Name
I/O Type
Voltage
I/O*
Reset State
Description
Dealing with Unused Pins
Nominal
Mux
60
LED0
Open Drain
O
1 and
Undefined
LED0 Output
NC
61
INT0
GPIO3
VCC_1V8
I
Z
Interruption 0 Input
If INT0 is not used, it should be
configured as GPIO
62
INT1
GPIO25
VCC_2V8
I
Z
Interruption 1 Input
If INT1 is not used, it should be
configured as GPIO
63
~RESET
VCC_1V8
I/O
RESET Input
NC or add a test point
64
PCM-SYNC
VCC_1V8
O
Pull-down
PCM Frame Synchro
NC
65
PCM-OUT
VCC_1V8
O
Pull-up
PCM Data Output
NC
66
PCM-IN
VCC_1V8
I
Pull-up
PCM Data Input
NC
67
PCM-CLK
VCC_1V8
O
Pull-down
PCM Clock
NC
68
BUZZER0
Open Drain
O
Z
Buzzer Output
NC
69
~CT109-DCD1
GPIO11
VCC_2V8
O
Undefined
Main RS232 Data Carrier
Detect
NC
70
~CT108-2-
DTR1
GPIO9
VCC_2V8
I
Z
Main RS232 Data Terminal
Ready
(DTR1) Pull-up to VCC_2V8 with
100kΩ
71
~CT125-RI
GPIO10
VCC_2V8
O
Undefined
Main RS232 Ring Indicator
NC
72
~CT107-DSR1
GPIO8
VCC_2V8
O
Z
Main RS232 Data Set
Ready
NC
73
~CT105-RTS1
GPIO6
VCC_2V8
I
Z
Main RS232 Request To
Send
(RTS1) Pull-up to VCC_2V8 with
100kΩ and add a test point for
firmware update
74
CT103-TXD1
GPIO4
VCC_2V8
I
Z
Main RS232 Transmit
(TXD1) Pull-up to VCC_2V8 with
100kΩ and add a test point for
firmware update
75–98
GND
* The I/O direction information is only for the nominal signal. When the signal is configured in GPIO, it can always be an Input or an Output.

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 19
AirPrime SL6087 User Guide
Interfaces
4.2. RF Interface
The RF (radio frequency) interface of the AirPrime SL6087 Embedded Module allows the
transmission of RF signals. This interface has a 50Ωnominal impedance and a 0ΩDC impedance.
4.2.1. RF Connections
The RF input/output of the AirPrime SL6087 Embedded Module is through one of the LGA pins (pin
22, ANT), with grounded LGA pins at both sides.
The ANT pin of the AirPrime SL6087 Embedded Module is ESD protected for both ±4KV contact and
±8KV air discharge.
4.2.2. Antenna Specifications
The antenna must meet the requirements specified in the table below.
The optimum operating frequency depends on the application. A dual-band, tri-band or quad-band
antenna should operate in these frequency bands and have the following characteristics.
Table 4: Antenna Specifications
Characteristic
GSM 850
PCS 1900
TX Frequency
824 to 849 MHz
1850 to 1910 MHz
RX Frequency
869 to 894 MHz
1930 to 1990 MHz
Impedance
50Ω
VSWR
RX max
1.5:1
TX max
1.5:1
Typical Radiated Gain
0dBi in one direction at least
Note: Sierra Wireless recommends a maximum VSWR of 1.5:1 for both TX and RX bands. Even so, all
aspects of this specification will be fulfilled even with a maximum VSWR of 2:1.

WA_DEV_SL6087_PTS_002 Rev 001 Jun 17, 2010 20
5. Certification Compliance and
Recommended Standards
5.1. Certification Compliance
The AirPrime SL6087 Embedded Module connected on a development kit board application is
compliant with the following requirements.
Table 5: Standards Conformity for the SL6087 Embedded Module
Domain
Applicable Standard
Safety standard
EN 60950-1 (ed.2006)
Health standard (EMF Exposure Evaluation)
EN 62311 (ed. 2008)
Efficient use of the radio frequency spectrum
EN 301 511 (V 9.0.2)
EMC
EN 301 489-1 (v1.8.1)
EN 301 489-7 (v1.3.1)
FCC
FCC Part 22, 24
IC
RSS-132 Issue 2
RSS-133 Issue 5
5.2. Applicable Standards Listing
The table hereafter gives the basic list of standards applicable for the AirPrime SL6087 Embedded
Module (2G (R99/Rel. 4)).
Note: References to any features can be found from these standards.
Table 6: Applicable Standards and Requirements for the SL6087 Embedded Module
Document
Current
Version
Title
NAPRD.03
5.3
Overview of PCS Type certification review board (PTCRB) Mobile Equipment
Type Certification and IMEI control
TS 51.010-1
9.1.0
3rd Generation Partnership Project; Technical Specification Group GSM/EDGE
Radio Access Network; Digital cellular telecommunications system (Phase 2+);
Mobile Station (MS) conformance specification; Part 1: Conformance
specification
TS 51.010-2
9.1.0
3rd Generation Partnership Project; Technical Specification Group GSM/EDGE
Radio Access Network; Mobile Station (MS) conformance specification; Part 2:
Protocol Implementation Conformance Statement (PICS) proforma specification
TS 51.010-4
4.14.1
3rd Generation Partnership Project; Technical Specification Group GSM/EDGE
Radio Access Network; Digital cellular telecommunications system (Phase 2+);
Mobile Station (MS) conformance specification; Part 4: SIM Application Toolkit
Conformance specification
ETSI 102.230
3.9.0
Smart cards; UICC-Terminal interface; Physical, electrical and logical test
specification(Release 99)