SIGMA TEK TAE 1044 User manual

TAE 1044
Build-in Touch Terminal
Operating Manual
| Date of creation: 03.06.2020
| Version date: 11.11.2020
| Article number: 12-200-1044-E

Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: [phone]
Fax: [phone]
Email: [email protected]
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2020
SIGMATEK GmbH & Co KG
Translation from German
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or distributed in any form
(print, photocopy, microfilm or in any other process) without express permission.
We reserve the right to make changes in the content without notice. SIGMATEK GmbH & Co KG is not responsible for technical or
printing errors in this handbook and assumes no responsibility for damages that occur through its use.

BUILD-IN TOUCH TERMINAL
TAE 1044
11.11.2020
Page 1
Build-in Touch Terminal
TAE 1044
The multi-touch operating panel TAE 1044 is used to visualize automated processes. The
operation and monitoring of automated procedures are simplified using this display unit. The
projective capacitive touch screen is used to enter process data and parameters. The output
is shown on a 10.1“ TFT color display with LED backlighting.
This module operates with SIGMATEK HMI-LINK generation 2.1 (G2.1). This allows a
transmission from the display, as well as USB signals using standard cables (CAT-5e or CAT-
6) from a remote PC to a terminal (up to 100 m).
Currently supported: PC 452-K, HMI-Link G2 insert (PC 301-E7) and HMI-Link G2 Box (PC
301-E8). A device equipped with a generation 2.1 SIGMATEK HMI-Link (G2.1) is also required
on the PC side; either integrated directly on the PC or as an external expansion box. With the
2 integrated USB connection, external end devices (mouse, keyboard ...) or memory (USB
stick) can be connection on the HMI side.

TAE 1044
BUILD-IN TOUCH TERMINAL
Page 2
11.11.2020
Table of Contents
TAE 1044..................................................................1
Build-in Touch Terminal.........................................1
Table of Contents ...................................................2
Introduction.............................................................6
Target Group/Purpose of this Operating Manual ...6
Important Reference Documentation .....................6
Contents of Delivery ..............................................6
Basic Safety Guidelines.........................................7
Symbols Used ........................................................7
Disclaimer ..............................................................8
General Safety Guidelines .....................................9
Standards and Guidelines....................................11
Guidelines ............................................................ 11
EU Conformity Declaration ............................... 11
Technical Data ......................................................12
Performance Data ................................................ 12
Electrical Requirements ....................................... 12
Display ................................................................. 13
Control Unit .......................................................... 14

BUILD-IN TOUCH TERMINAL
TAE 1044
11.11.2020
Page 3
Minimum Distance between Operating Elements for Multi-touch
Applications ......................................................... 15
Environmental Conditions ................................... 16
Miscellaneous ..................................................... 17
Interfaces..............................................................18
Front Connectors ................................................ 18
X1: Supply (4-pin Phoenix RM 3.5) .................. 18
X2: HMI Remote-IN (HMI-Link G2.1, Industrial Mini I/O) 19
X3: Service ....................................................... 19
X4, X5: USB 2.0 (Type A) ................................ 20
X6: Panel Interface Connector ......................... 20
Applicable Connectors ........................................ 21
Status Display LEDs............................................ 22
Mechanical Dimensions.......................................23
Assembly/Installation ..........................................26
Check Contents of Delivery ................................. 26
Installation ........................................................... 26
Mounting Instructions .......................................... 26
Restricted Space Around Rear Trimming ......... 27
Required Cutout for Mounting the Terminal ..... 28
Mounting Position ............................................. 29

TAE 1044
BUILD-IN TOUCH TERMINAL
Page 4
11.11.2020
Wiring ....................................................................30
Grounding ............................................................ 30
Shielding .............................................................. 30
ESD Protection .................................................... 31
USB Interface ...................................................... 31
Transport/Storage.................................................32
Storage ..................................................................33
Maintenance..........................................................34
Cleaning and Disinfecting the Touch Screen ....... 34
Service ................................................................. 35
Calibrating the Touch Screen ........................... 35
Repair .................................................................. 36
Position Series Label Sub Device ........................ 36
Modularity..............................................................37
Removing the PIM from the Touch Panel ............ 37
Mounting the PIM onto the Touch Panel .............. 38
Display „Burn-In“ Effect.......................................39
Disposal.................................................................40
Accessories...........................................................41
Touch Pen ........................................................... 41
Changes Chart......................................................42

BUILD-IN TOUCH TERMINAL
TAE 1044
11.11.2020
Page 5

TAE 1044
BUILD-IN TOUCH TERMINAL
Page 6
11.11.2020
Introduction
Target Group/Purpose of this Operating Manual
This operating manual contains all information required for the operation of the product.
This operating manual is intended for:
• Project planners
• Technicians
• Commissioning engineers
• Machine operators
• Maintenance/test technicians
General knowledge of automation technology is required.
Further help and training information, as well as the appropriate accessories can be found
on our website www.sigmatek-automation.com.
Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.
Important Reference Documentation
• TP XX61
• PIM 021
This and additional documents can be downloaded from our website or obtained through
support.
Contents of Delivery
1x TAE 1044
8x angle bracket
1x 4-pin Phoenix connector plug
2x M3 TX10 Torx screws

BUILD-IN TOUCH TERMINAL
TAE 1044
11.11.2020
Page 7
Basic Safety Guidelines
Symbols Used
The following symbols are used in the operator documentation for warning and danger
messages, as well as informational notes.
DANGER
Danger indicates that death or serious injury will occur, if the
specified measures are not taken.
• To avoid death or serious injuries, observe the all guidelines.
Danger indique une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
• Respectez toutes les consignes pour éviter des blessures graves,
voire mortelles.
WARNING
Warning indicates that death or serious injury can occur, if the
specified measures are not taken.
• To avoid death or serious injuries, observe the all guidelines.
Avertissement d’une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
• Respectez toutes les consignes pour éviter des blessures graves,
voire mortelles.
CAUTION
Caution indicates that moderate to slight injury can occur, if the
specified measures are not taken.
• To avoid moderate to slight injuries, observe the all guidelines.
Attention indique une situation dangereuse qui, faute de prendre les
mesures adéquates, peut entraîner des blessures assez graves ou
légères.
• Respectez toutes les consignes pour éviter des blessures graves,
voire mortelles.
CAUTION

TAE 1044
BUILD-IN TOUCH TERMINAL
Page 8
11.11.2020
Danger for ESD-sensitive components.
Les signes de danger pour les composants sensibles aux décharges
électrostatiques.
INFORMATION
INFORMATION
• Provides important information on the product, handling or
relevant sections of the documentation, which require particular
attention.
Disclaimer
INFORMATION
The contents of this operating manual were prepared with the greatest
care. However, deviations cannot be ruled out. This operating manual is
regularly checked and required corrections are included in the subsequent
versions. The machine manufacturer is responsible for the proper
assembly, as well as device configuration. The machine operator is
responsible for safe handling, as well as proper operation.
The current operating manual can be found on our website. If necessary,
contact our support.
Subject to technical changes, which improve the performance of the
devices. The following operating manual is purely a product description. It
does not guarantee properties under the warranty.
Please thoroughly read the corresponding documents and this operating
manual before handling a product.
SIGMATEK GmbH & Co KG is not liable for damages caused through,
non-compliance with these instructions or applicable regulations.

BUILD-IN TOUCH TERMINAL
TAE 1044
11.11.2020
Page 9
General Safety Guidelines
The Safety Guidelines in the other sections of this operating manual must be observed.
These instructions are visually emphasized by symbols.
INFORMATION
According to EU Guidelines, the operating manual is a component of a
product.
This operating manual must therefore be accessible in the vicinity of the
machine since it contains important instructions.
This operating manual should be included in the sale, rental or transfer of
the product, or its online availability indicated.
Maintain this operating manual in readable condition and keep it
accessible for reference.
Regarding the requirements for Safety and health connected to the use of
machines, the manufacturer must perform a risk assessment in
accordance with machine guidelines 2006/42/EG before introducing a
machine to the market. Before commissioning this product, check that
conformance with the provisions of the 2006/42/EG guidelines is correct.
As long as the machine with which the product should be used does not
comply with the guideline, operating this product is prohibited.
Operate the unit with devices and accessories approved by SIGMATEK
only.
CAUTION
Handle the device with care and do not drop or let fall.
Prevent foreign bodies and fluids from entering the device.
The device must not be opened, otherwise it could be damaged!
Manipulez l’appareil avec précaution et ne le laissez pas tomber.
Empêchez les corps étrangers et les liquides de pénétrer dans l’appareil.
L’appareil ne doit pas être ouvert, sinon il risque d’être endommagé!
The module complies with EN 61131-2.
In combination with a machine, the machine builder must comply with EN
60204-1 standards.
For your own safety and that of others, compliance with the environmental
conditions is essential.

TAE 1044
BUILD-IN TOUCH TERMINAL
Page 10
11.11.2020
The control cabinet must be connected to ground correctly.
To perform maintenance or repairs, disconnect the system from the power
supply.
Le module est conforme à la norme EN 61131-2.
En combinaison avec une machine, le constructeur de la machine doit
respecter la norme EN 60204-1.
L’armoire de commande doit être raccordée correctement à la terre.
Pour l'entretien et les réparations, débranchez le système de l'alimentation.

BUILD-IN TOUCH TERMINAL
TAE 1044
11.11.2020
Page 11
Standards and Guidelines
Guidelines
The product was constructed in compliance with the following European Union guidelines
and tested for conformity.
EU Conformity Declaration
EU Declaration of Conformity
The product TAE 1044 conforms to the following European guidelines:
• 2014/35/EU Low-voltage Guideline
• 2014/30/EU Electromagnetic Compatibility (EMC Guideline)
• 2011/65/EU “Restricted use of certain hazardous substances in
electrical and electronic equipment” (RoHS Guideline)
The EU Conformity Declarations are provided on the SIGMATEK website. See
Products/Downloads or use the search function and the keyword “EU
Declaration of Conformity”.

TAE 1044
BUILD-IN TOUCH TERMINAL
Page 12
11.11.2020
Technical Data
Performance Data
Interfaces
1x HMI Remote IN (HMI-Link G2.1)
2x USB 2.0 Type A OUT
1x Panel Interface Connector (for connecting a SIGMATEK TP)
Internal interfaces
(via Panel Interface
Connector)
USB 2.0 (for touch and front USB, if available on the TP)
Status LEDs
1x green
1x red (depends on OS)
Display
Resolution
10.1“ TFT color display
WXGA 1280 x 800 pixels
Operating field
touch screen (projective capacitive)
Cooling
passive (fanless)
Electrical Requirements
Supply voltage
+24 V DC ±20 % (SELV/PELV)
UL: Class 2 or LVLC(1)
Current consumption of
(+24 V) power supply
typically 700 mA
(with no external devices connected)
maximum 900 mA
(with external devices connected)
Inrush current with 24 V/10
A fixed voltage supply
maximum 3 A (for 14 ms, load-dependent)
Inrush current without
current-limiting supply
maximum 71 A (for 1.5 ms, load-dependent)
INFORMATION
(1) For USA and Canada:
The supply must be limited to:
a) max. 5 A at voltages from 0-20 V DC, or
b) 100 W at voltages from 20-60 V DC
The limiting component (e.g. transformer, power supply or fuse) must be
certified by an NRTL (Nationally Recognized Testing Laboratory).

BUILD-IN TOUCH TERMINAL
TAE 1044
11.11.2020
Page 13
Display
Type
10.1” IPS color display
Resolution
WXGA 1280 x 800 pixels
Color depth
18-bit RGB
LCD mode
normally black(1)
LCD Polarizer
transmissive(2)
Pixel size
0.1695 x 0.1695 mm
Active range
216.96 x 135.60 mm
Backlighting
LED
Contrast ratio
typically 1000:1
Brightness
typically 500 cd/m²
Angle CR ≥ 10
all directions typically 85°(3)
Life span
By compliance with the ambient conditions, the brightness of the display sinks
after 50,000 operating hours to 50 % of the original brightness.
(1) If there is no display data, the display is black.
(2) Display technology, with which display backlighting is used.
(3) The viewing angle is measured from the normal to the display surface.
Due to the manufacturing process, individual pixel errors cannot be excluded to 100 % and therefore do not constitute
a reduction in quality.

TAE 1044
BUILD-IN TOUCH TERMINAL
Page 14
11.11.2020
Control Unit
Touch panel
projective capacitive touch panel
Cleaning
see chapter: FEHLERHAFTER QUERVERWEIS Cleaning and Disinfecting the Touch
Screen
INFORMATION
A projective capacitive touch screen is built into the panel, with which 10-
finger input, zoom and gesture functions can be implemented. Data can be
input using fingers, a project capacitive touch pen as well as with thin gloves.
The device must always be grounded to ensure stable function of the touch
screen. The touch function may still have to be individually adapted to the
respective environmental conditions.

BUILD-IN TOUCH TERMINAL
TAE 1044
11.11.2020
Page 15
Minimum Distance between Operating Elements for Multi-touch Applications
To guarantee smooth operation with multi-touch applications, buttons and control elements
that should be operated at the same time must have the minimum clearance shown below
(depending on the estimated touch point).
INFORMATION
The size of the buttons and operating elements directly affect the
operability of the application. Small operating elements should therefore
be avoided.

TAE 1044
BUILD-IN TOUCH TERMINAL
Page 16
11.11.2020
Environmental Conditions
Storage temperature
-25 ... +85 °C
Environmental temperature
0 ... +50 °C(1)
Humidity
10-95 %, non-condensing
Installation altitude above
sea level
0-2000 m without derating
> 2000 m up to a maximum of 5000 m with derating of the maximum
environmental temperature by 0.5 °C per 100 m
Operating conditions
pollution degree 2
EMC resistance(2)
in accordance with EN 61000-6-2 (industrial area)
in accordance with EN 61000-6-1 (living area)
EMC noise emission(2)
in accordance with EN 61000-6-4 (industrial area)
in accordance with EN 61000-6-3 (living area)
Vibration resistance
EN 60068-2-6
5-200 Hz: amplitude 3.5 mm
transition frequency: 8.42454 Hz
acceleration: 1 g
duration: 10 cycles
cycle: 1 octave/minute
Shock resistance
EN 60068-2-27
15 g (147.15 m/s2)
Protection type(2)
EN 60529
protection through housing
front: IP65cover: IP20
(not UL-listed)
(1) The maximum environmental temperature allowed depends on the TP connected. The ambient temperature cannot
exceed any of the permissible values.
(2) Applies only if the PIM 021 is mounted onto the TP.

BUILD-IN TOUCH TERMINAL
TAE 1044
11.11.2020
Page 17
Miscellaneous
Article number
12-200-1044
Hardware version
1.x
Operating system
-
Standard
designed according to UL
Approvals
CE
CAUTION
If the modular components (e.g. TP and PIM) are not bolted together,they
are NOT ESD-protected and can only be unpacked and handled in an
ESD-safe environment by trained personnel.
To avoid damage to the electronics, never handle the circuit board itself
without the appropriate ESD protection. It is recommended that any
physical contact with the circuit board be avoided (body and/or objects).

TAE 1044
BUILD-IN TOUCH TERMINAL
Page 18
11.11.2020
Interfaces
Front Connectors
X1: Supply (4-pin Phoenix RM 3.5)
Pin
Function
1
+24 V DC
2
+24 V DC
3
GND
4
GND