SIGMA TEK TAE 1244 User manual

Date of creation: 03.06.2020 Version date: 11.11.2020 Article number: 12-200-1244-E
TAE 1244
Build-in Touch Terminal
Operating Manual

Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: [phone]
Fax: [phone]
Email: [e-mail]
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2020
SIGMATEK GmbH & Co KG
Translation from German
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or
distributed in any form (print, photocopy, microfilm or in any other process) without express permission.
We reserve the right to make changes in the content without notice. SIGMATEK GmbH & Co KG is not
responsible for technical or printing errors in this handbook and assumes no responsibility for damages that
occur through its use.

BUILD-IN TOUCH TERMINAL TAE 1244
Build-in Touch Terminal TAE 1244
The multi-touch operating panel TAE 1244 is used to visualize automated processes. The
operation and monitoring of automated procedures are simplified using this display unit.
The projective capacitive touch screen is used to enter process data and parameters. The
output is shown on a 12.1“ TFT color display with LED backlighting.
This module operates with SIGMATEK HMI-LINK generation 2.1 (G2.1). This allows a
transmission from the display, as well as USB signals using standard cables (CAT-5e or
CAT-6) from a remote PC to a terminal (up to 100 m).
Currently supported: PC 452-K, HMI-Link G2 insert (PC 301-E7) and HMI-Link G2 Box (PC
301-E8). A device equipped with a generation 2.1 SIGMATEK HMI-Link (G2.1) is also
required on the PC side; either integrated directly on the PC or as an external expansion
box. With the 2 integrated USB connection, external end devices (mouse, keyboard ...) or
memory (USB stick) can be connection on the HMI side.
11.11.2020 Page 1

TAE 1244 BUILD-IN TOUCH TERMINAL
Table of Contents
1 Introduction 5
1.1 Target Group/Purpose of this Operating Manual 5
1.2 Important Reference Documentation 5
1.3 Contents of Delivery 5
2 Basic Safety Guidelines 6
2.1 Symbols Used 6
2.2 Disclaimer 8
2.3 General Safety Guidelines 9
3 Standards and Guidelines 11
3.1 Guidelines 11
3.1.1 EU Conformity Declaration 11
4 Technical Data 12
4.1 Performance Data 12
4.2 Electrical Requirements 12
4.3 Display 13
4.4 Control Unit 13
4.5 Minimum Distance between Operating Elements for Multi-touch Applications 14
4.6 Environmental Conditions 15
4.7 Miscellaneous 16
5 Interfaces 17
5.1 Front Connectors 17
5.1.1 X1: Supply (4-pin Phoenix RM 3.5) 17
5.1.2 X2: HMI Remote-IN (HMI-Link G2.1, Industrial Mini I/O) 18
5.1.3 X3: Service 18
5.1.4 X4, X5: USB 2.0 (Type A) 19
Page 2 11.11.2020

BUILD-IN TOUCH TERMINAL TAE 1244
5.1.5 X6: Panel Interface Connector 19
5.2 Applicable Connectors 19
5.3 Status Display LEDs 20
6 Mechanical Dimensions 21
7 Assembly/Installation 23
7.1 Check Contents of Delivery 23
7.2 Installation 23
7.3 Mounting Instructions 23
7.3.1 Restricted Space Around Rear Trimming 24
7.3.2 Required Cutout for Mounting the Terminal 25
7.3.3 Mounting Position 26
8 Wiring 27
8.1 Grounding 27
8.2 Shielding 27
8.3 ESD Protection 28
8.4 USB Interface 28
9 Transport/Storage 29
10 Storage 30
11 Maintenance 31
11.1 Cleaning and Disinfecting the Touch Screen 31
11.2 Service 32
11.2.1 Calibrating the Touch Screen 32
11.3 Repair 32
11.4 Position Series Label Sub Device 33
12 Modularity 34
12.1 Removing the PIM from the Touch Panel 34
11.11.2020 Page 3

TAE 1244 BUILD-IN TOUCH TERMINAL
12.2 Mounting the PIM onto the Touch Panel 35
13 Display „Burn-In“ Effect 36
14 Disposal 37
15 Accessories 38
15.1 Touch Pen 38
Page 4 11.11.2020

BUILD-IN TOUCH TERMINAL TAE 1244
1 Introduction
1.1 Target Group/Purpose of this Operating Manual
This operating manual contains all information required for the operation of the product.
This operating manual is intended for:
lProject planners
lTechnicians
lCommissioning engineers
lMachine operators
lMaintenance/test technicians
General knowledge of automation technology is required.
Further help and training information, as well as the appropriate accessories can be found
on our website www.sigmatek-automation.com.
Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.
1.2 Important Reference Documentation
lTP XX61
lPIM 021
This and additional documents can be downloaded from our website or obtained through
support.
1.3 Contents of Delivery
1x TAE 1244
8x angle bracket
1x 4-pin Phoenix connector plug
2x M3 TX10 Torx screws
11.11.2020 Page 5

TAE 1244 BUILD-IN TOUCH TERMINAL
2 Basic Safety Guidelines
2.1 Symbols Used
The following symbols are used in the operator documentation for warning and danger
messages, as well as informational notes.
DANGER
Danger indicates that death or serious injury will occur, if the
specified measures are not taken.
To avoid death or serious injuries, observe the all guidelines.
Danger indique une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
WARNING
Warning indicates that death or serious injury can occur, if the
specified measures are not taken.
To avoid death or serious injuries, observe the all guidelines.
Avertissement d’une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
Page 6 11.11.2020

BUILD-IN TOUCH TERMINAL TAE 1244
CAUTION
Caution indicates that moderate to slight injury can occur, if the
specified measures are not taken.
To avoid moderate to slight injuries, observe the all guidelines.
Attention indique une situation dangereuse qui, faute de prendre les
mesures adéquates, peut entraîner des blessures assez graves ou
légères.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
CAUTION
Danger for ESD-sensitive components.
Les signes de danger pour les composants sensibles aux décharges
électrostatiques.
INFORMATION
INFORMATION
Provides important information on the product, handling or
relevant sections of the documentation, which require
particular attention.
11.11.2020 Page 7

TAE 1244 BUILD-IN TOUCH TERMINAL
2.2 Disclaimer
INFORMATION
The contents of this operating manual were prepared with the greatest
care. However, deviations cannot be ruled out. This operating manual is
regularly checked and required corrections are included in the
subsequent versions. The machine manufacturer is responsible for the
proper assembly, as well as device configuration. The machine
operator is responsible for safe handling, as well as proper operation.
The current operating manual can be found on our website. If
necessary, contact our support.
Subject to technical changes, which improve the performance of the
devices. The following operating manual is purely a product description.
It does not guarantee properties under the warranty.
Please thoroughly read the corresponding documents and this
operating manual before handling a product.
SIGMATEK GmbH & Co KG is not liable for damages caused
through, non-compliance with these instructions or applicable
regulations.
Page 8 11.11.2020

BUILD-IN TOUCH TERMINAL TAE 1244
2.3 General Safety Guidelines
The Safety Guidelines in the other sections of this operating manual must be observed.
These instructions are visually emphasized by symbols.
INFORMATION
According to EU Guidelines, the operating manual is a component of a
product.
This operating manual must therefore be accessible in the vicinity of the
machine since it contains important instructions.
This operating manual should be included in the sale, rental or transfer
of the product, or its online availability indicated.
Maintain this operating manual in readable condition and keep it
accessible for reference.
Regarding the requirements for Safety and health connected to the use
of machines, the manufacturer must perform a risk assessment in
accordance with machine guidelines 2006/42/EG before introducing a
machine to the market. Before commissioning this product, check that
conformance with the provisions of the 2006/42/EG guidelines is
correct. As long as the machine with which the product should be used
does not comply with the guideline, operating this product is prohibited.
Operate the unit with devices and accessories approved by SIGMATEK
only.
11.11.2020 Page 9

TAE 1244 BUILD-IN TOUCH TERMINAL
CAUTION
Handle the device with care and do not drop or let fall.
Prevent foreign bodies and fluids from entering the device.
The device must not be opened, otherwise it could be damaged!
Manipulez l’appareil avec précaution et ne le laissez pas tomber.
Empêchez les corps étrangers et les liquides de pénétrer dans
l’appareil.
L’appareil ne doit pas être ouvert, sinon il risque d’être endommagé!
The module complies with EN 61131-2.
In combination with a machine, the machine builder must comply with
EN 60204-1 standards.
For your own safety and that of others, compliance with the
environmental conditions is essential.
The control cabinet must be connected to ground correctly.
To perform maintenance or repairs, disconnect the system from the
power supply.
Le module est conforme à la norme EN 61131-2.
En combinaison avec une machine, le constructeur de la machine doit
respecter la norme EN 60204-1.
L’armoire de commande doit être raccordée correctement à la terre.
Pour l'entretien et les réparations, débranchez le système de
l'alimentation.
Page 10 11.11.2020

BUILD-IN TOUCH TERMINAL TAE 1244
3 Standards and Guidelines
3.1 Guidelines
The product was constructed in compliance with the following European Union guidelines
and tested for conformity.
3.1.1 EU Conformity Declaration
EU Declaration of Conformity
The product TAE 1244 conforms to the following European guidelines:
2014/35/EU Low-voltage Guideline
2014/30/EU Electromagnetic Compatibility (EMC Guideline)
2011/65/EU “Restricted use of certain hazardous substances in
electrical and electronic equipment” (RoHS Guideline)
The EU Conformity Declarations are provided on the SIGMATEK website.
See Products/Downloads or use the search function and the keyword “EU
Declaration of Conformity”.
11.11.2020 Page 11

TAE 1244 BUILD-IN TOUCH TERMINAL
4 Technical Data
4.1 Performance Data
Interfaces 1x HMI Remote IN (HMI-Link G2.1)
2x USB 2.0 Type A OUT
1x Panel Interface Connector (for connecting a SIGMATEK TP)
Internal interfaces
(via Panel Interface Connector)
USB 2.0 (for touch and front USB, if available on the TP)
Status LEDs 1x green
1x red (depends on OS)
Display
Resolution
12.1“ TFT color display
WXGA 1280 x 800 pixels
Operating field touch screen (projective capacitive)
Cooling passive (fanless)
4.2 Electrical Requirements
Supply voltage +24 V DC ±20 % (SELV/PELV)
UL: Class 2 or LVLC(1)
Current consumption of (+24 V)
power supply
typically 800 mA
(with no external devices
connected)
maximum 1000 mA
(with external devices connected)
Inrush current with 24 V/10 A
fixed voltage supply
maximum 3.1 A (for 17 ms, load-dependent)
Inrush current without current-
limiting supply
maximum 76 A (for 1.2 ms, load-dependent)
INFORMATION
(1) For USA and Canada:
The supply must be limited to:
a) max. 5 A at voltages from 0-20 V DC, or
b) 100 W at voltages from 20-60 V DC
The limiting component (e.g. transformer, power supply or fuse) must be
certified by an NRTL (Nationally Recognized Testing Laboratory).
Page 12 11.11.2020

BUILD-IN TOUCH TERMINAL TAE 1244
4.3 Display
Type 12.1” TN color display
Resolution WXGA 1280 x 800 pixels
Color depth 18-bit RGB
LCD mode normally black(1)
LCD Polarizer transmissive(2)
Pixel size 0.204 x 0.204 mm
Active range 261.12 x 163.2 mm
Backlighting LED
Contrast ratio typically 1000:1
Brightness typically 400 cd/m²
Angle CR ≥ 10 all directions typically 89°(3)
Life span By compliance with the ambient conditions, the brightness of the display
sinks after 50,000 operating hours to 50 % of the original brightness.
(1) If there is no display data, the display is black.
(2) Display technology, with which display backlighting is used.
(3) The viewing angle is measured from the normal to the display surface.
Due to the manufacturing process, individual pixel errors cannot be excluded to 100 % and therefore do not constitute a
reduction in quality.
4.4 Control Unit
Touch panel projective capacitive touch panel
Cleaning see chapter: 11.1 Cleaning and Disinfecting the Touch Screen
INFORMATION
A projective capacitive touch screen is built into the panel, with which
10-finger input, zoom and gesture functions can be implemented. Data
can be input using fingers, a project capacitive touch pen as well as
with thin gloves. The device must always be grounded to ensure stable
function of the touch screen. The touch function may still have to be
individually adapted to the respective environmental conditions.
11.11.2020 Page 13

TAE 1244 BUILD-IN TOUCH TERMINAL
4.5 Minimum Distance between Operating Elements for Multi-touch
Applications
To guarantee smooth operation with multi-touch applications, buttons and control elements
that should be operated at the same time must have the minimum clearance shown below
(depending on the estimated touch point).
INFORMATION
The size of the buttons and operating elements directly affect the
operability of the application. Small operating elements should
therefore be avoided.
Page 14 11.11.2020

BUILD-IN TOUCH TERMINAL TAE 1244
4.6 Environmental Conditions
Storage temperature -25 ... +85 °C
Environmental temperature 0 ... +50 °C(1)
Humidity 10-95 %, non-condensing
Installation altitude above sea
level
0-2000 m without derating
> 2000 m up to a maximum of 5000 m with derating of the maximum
environmental temperature by 0.5 °C per 100 m
Operating conditions pollution degree 2
EMC resistance(2) in accordance with EN 61000-6-2 (industrial area)
in accordance with EN 61000-6-1 (living area)
EMC noise emission(2) in accordance with EN 61000-6-4 (industrial area)
in accordance with EN 61000-6-3 (living area)
Vibration resistance EN 60068-2-6 5-200 Hz: amplitude 3.5 mm
transition frequency: 8.42454 Hz
acceleration: 1 g
duration: 10 cycles
cycle: 1 octave/minute
Shock resistance EN 60068-2-27 15 g (147.15 m/s2)
Protection type(2) EN 60529
protection through housing
front: IP65
cover: IP20
(not UL-listed)
(1) The maximum environmental temperature allowed depends on the TP connected. The ambient temperature cannot
exceed any of the permissible values.
(2) Applies only if the PIM 021 is mounted onto the TP.
11.11.2020 Page 15

TAE 1244 BUILD-IN TOUCH TERMINAL
4.7 Miscellaneous
Article number 12-200-1244
Hardware version 1.x
Operating system -
Standard UL in preparation
Approvals CE
CAUTION
If the modular components (e.g. TP and PIM) are not bolted
together,they are NOT ESD-protected and can only be unpacked and
handled in an ESD-safe environment by trained personnel.
To avoid damage to the electronics, never handle the circuit board itself
without the appropriate ESD protection. It is recommended that any
physical contact with the circuit board be avoided (body and/or objects).
Page 16 11.11.2020

BUILD-IN TOUCH TERMINAL TAE 1244
5 Interfaces
5.1 Front Connectors
5.1.1 X1: Supply (4-pin Phoenix RM 3.5)
Pin Function
1 +24 V DC
2 +24 V DC
3 GND
4 GND
11.11.2020 Page 17

TAE 1244 BUILD-IN TOUCH TERMINAL
5.1.2 X2: HMI Remote-IN (HMI-Link G2.1, Industrial Mini I/O)
Pin Function
1 Tx+/DA+
2 Tx-/DA-
3 Rx+/DB+
4 DC+
5 DC-
6 Rx-/DB-
7 DD+
8 DD-
5.1.3 X3: Service
Pin Function
1 GND
2 TxD
3 RxD
4 n.c.
n.c. = do not use
INFORMATION
For service purposed only!
For the service interface, only a separate cable that can be
ordered from SIGMATEK may be used. Using a different cable
can lead to malfunction and damage.
Page 18 11.11.2020