SignaMax C-310 Series User manual

– 1 –
Quick Start Guide
1. Mount the Switch
Mounting the Switch in a Rack
1. Attach the brackets to the switch using the included screws.
2. Use the screws and cage/clip nuts supplied with the rack to
secure the switch in the rack.
2. Ground the Switch
1. Ensure the rack on which the switch is to be mounted is properly
grounded and in compliance with ETSI ETS 300 253. Verify that
there is a good electrical connection to the grounding point on
the rack (no paint or isolating surface treatment).
2. Attach a lug (not provided) to a #12 AWG (PoE switch) or #18
AWG (non-PoE switch) minimum grounding wire (not provided),
and connect it to the grounding point on the switch rear panel.
Then connect the other end of the wire to rack ground.
3. Connect Power
1. Plug the AC power cord into the socket on the rear of the switch.
2. Connect the other end of the power cord to an AC power
source.
4. Verify Basic Switch Operation
1. Verify basic switch operation by checking the system LEDs.
When operating normally, the Power and System LEDs should
be on green.
Note: The C-310 Series switches are for indoor use only.
Note: For safety and regulatory information, refer to the
Safety and Regulatory Information document included with
the switch.
Note: Other documentation, including the Installation
Guide, Web Management Guide, and CLI Reference
Guide, can be obtained from www.signamax.com
Note: The switch drawings in this document are for
illustration only and may not match your particular switch
model.
Caution: Installing the switch in a rack requires two people.
One person should position the switch in the rack, while the
other secures it using the rack screws.
Note: The switches can also be installed on a desktop or
shelf using the included adhesive rubber feet.
1
2
1
2
Caution: The earth connection must not be removed
unless all supply connections have been disconnected.
Caution: The device must be installed in a restricted-
access location. It should have a separate protective
earthing terminal on the chassis that must be permanently
connected to earth to adequately ground the chassis and
protect the operator from electrical hazards.
1
2
1
E102020-CS-R01
C-310 Series Gigabit Managed Switch
Package Contents
1. C-310 Series Switch
2. Rack Mounting Kit—brackets and screws
3. Power cord—US, Continental Europe, or UK
4. Four adhesive rubber feet
5. Documentation—Quick Start Guide (this document) and
Safety and Regulatory Information
1 2 3 4 5
www.signamax.com

Quick Start Guide
– 2 –
5. Connect Network Cables
1. For the RJ-45 ports, connect 100-ohm Category 5, 5e or better
twisted-pair cable.
2. For the SFP slots, first install SFP transceivers and then
connect fiber optic cabling to the transceiver ports.
The following transceivers are supported:
■1000BASE-SX (065-79SXMG)
■1000BASE-LX (065-79LXMG)
■1000BASE-ZX (065-79ZXMG)
■1000BASE-LHX (065-79LXEDMG)
For fiber transceivers, it is suggested to use UL-certified devices
that meet Laser Class I emission levels. Rated voltage and
current as 3-3.6V / 0.1-0.3A.
3. As connections are made, check the port status LEDs to be sure
the links are valid.
For the RJ-45 ports:
■Green — A valid 1 Gbps link. Flashing indicates activity.
■Orange — A valid 10/100 Mbps link. Flashing indicates
activity.
For the SFP ports:
■Green — A valid 1 Gbps link. Flashing indicates activity.
6. Connect to the Web User Interface
1. Connect a PC directly to one of the switch’s RJ-45 ports.
2. Set the PC IP address to be on the same subnet as the switch
(that is, the PC and switch IP addresses must both start
192.168.2.x with subnet mask 255.255.255.0).
3. Enter the switch’s default management IP address of
192.168.2.10 into the web browser address bar.
4. Log in to the web interface using the default settings:
User Name = admin
Password = admin
1
2
Note: For further information on switch configuration, refer
to the Web Management Guide and CLI Reference Guide.
Switch Chassis
Size (WxDxH) 440 x 316.5 x 44 mm (17.25 x 12.46 x 1.74 in.)
Weight 4.665 kg (10.28 lb)
Temperature Operating: 0° C to 50° C (32° F to 122° F)
Storage: -40° C to 70° C (-40° F to 158° F)
Humidity Operating: 10% to 90% (non-condensing)
Power Specifications
AC Input 100–240 VAC, 50-60 Hz, 15 A
Power
Consumption
770 W maximum
PoE Power
Budget
740 W
Regulatory Compliances
Emissions EN 55032:2015, Class A
EN 61000-3-2:2014, Class A
EN 61000-3-3:2013, Class A
47 CFR FCC Part 15:2015, Subpart B, Class A
CE Mark
VCCI Class A
Immunity EN 55024:2010+A1:2015
IEC 61000-4-2/3/4/5/6/8/11
Safety CB (IEC/EN60950-1)
Hardware Specifications
www.signamax.com