SignaMax 065-7726SPOE User manual

SignamaxConnectivity Systems
Model 065-7726SPOE
24-Port PoE Managed
Fast Ethernet Switch
with 2 SFP Dual Media Ports
U s e r ’ s G u i d e

Signamax
065-7726SPOE
User's Manual
24-Port PoE Managed Fast Ethernet Switch
with 2 SFP Dual Media Ports
Release 0.92

ii

iii
Table of Contents
CAUTION --------------------------------------------------------------------------------------VII
ELECTRONIC EMISSION NOTICES ---------------------------------------------------------VII
CHAPTER 1. INTRODUCTION---------------------------------------------------------- 2
1-1. OVERVIEW OF THE 065-7726SPOE ------------------------------------------------ 2
1-2. CHECKLIST ------------------------------------------------------------------------------- 4
1-3. FEATURES-------------------------------------------------------------------------------- 4
1-4. VIEW OF THE 065-7726SPOE------------------------------------------------------- 7
1-4-1. User Interfaces on the Front Panel (Button, LEDs and Plugs) ----- 7
1-4-2. User Interfaces on the Rear Panel ----------------------------------------- 9
1-5. VIEW OF THE OPTIONAL MODULES ------------------------------------------------ 10
CHAPTER 2. INSTALLATION ----------------------------------------------------------11
2-1. STARTING 065-7726SPOE UP-----------------------------------------------------11
2-1-1. Hardware and Cable Installation-------------------------------------------11
2-1-2. Installing Chassis to a 19-Inch Wiring Closet Rail-------------------- 13
2-1-3. Cabling Requirements------------------------------------------------------- 13
2-1-3-1. Cabling Requirements for TP Ports -------------------------------- 14
2-1-3-2. Cabling Requirements for 1000SX/LX SFP Module ----------- 14
2-1-3-3. Switch Cascading in Topology--------------------------------------- 15
2-1-4. Configuring the Management Agent of the 065-7726SPOE------- 18
2-1-4-1. Configuring the Management Agent of the 065-7726SPOE
through the Serial RS-232 Port ------------------------------------- 19
2-1-4-2. Configuring the Management Agent of the 065-7726SPOE
through the Ethernet Port--------------------------------------------- 22
2-1-5. IP Address Assignment------------------------------------------------------ 23
2-2. TYPICAL APPLICATIONS -------------------------------------------------------------- 29
CHAPTER 3. OPERATION OF WEB-BASED MANAGEMENT-------------- 31
3-1. WEB MANAGEMENT HOME OVERVIEW -------------------------------------------- 33
3-1-1. System Information----------------------------------------------------------- 36
3-1-2. IP Configuration --------------------------------------------------------------- 38
3-1-3. Time Configuration ----------------------------------------------------------- 41
3-1-4. Account Configuration ------------------------------------------------------- 44
3-1-5. Management Security ------------------------------------------------------- 45
3-1-6. Virtual Stack -------------------------------------------------------------------- 48
3-2. PORT CONFIGURATION--------------------------------------------------------------- 50
3-2-1.Port Status----------------------------------------------------------------------- 50
3-2-2. Port Configuration ------------------------------------------------------------ 55
3-2-3. Simple Counter ---------------------------------------------------------------- 57
3-2-4. Detail Counter ----------------------------------------------------------------- 59

iv
3-3. POE------------------------------------------------------------------------------------- 62
3-4. SNMP CONFIGURATION ------------------------------------------------------------- 66
3-5. DHCP BOOT -------------------------------------------------------------------------- 68
3-6. IGMP SNOOPING --------------------------------------------------------------------- 69
3-7. VLAN----------------------------------------------------------------------------------- 73
3-7-1. VLAN Mode -------------------------------------------------------------------- 73
3-7-2. Tag-based Group ------------------------------------------------------------- 75
3-7-3. PVID------------------------------------------------------------------------------ 78
3-7-4. Port-based Group------------------------------------------------------------- 80
3-8. MAC TABLE---------------------------------------------------------------------------- 82
3-9. GVRP CONFIGURATION ------------------------------------------------------------- 89
3-10. STP CONFIGURATION -------------------------------------------------------------- 95
3-10-1. STP Status -------------------------------------------------------------------- 95
3-10-2. STP Configuration ---------------------------------------------------------- 97
3-10-3. STP Port Configuration ---------------------------------------------------- 99
3-11. TRUNKING CONFIGURATION ------------------------------------------------------103
3-12. 802.1X CONFIGURATION ---------------------------------------------------------- 111
3-13. ALARM CONFIGURATION ----------------------------------------------------------121
3-14. CONFIGURATION--------------------------------------------------------------------124
3-14-1. Save/Restore----------------------------------------------------------------125
3-14-2. Config File--------------------------------------------------------------------128
3-15. SECURITY ---------------------------------------------------------------------------129
3-16. BANDWIDTH MANAGEMENT-------------------------------------------------------132
3-17. QOS(QUALITY OF SERVICE)CONFIGURATION --------------------------------136
3-18. DIAGNOSTICS -----------------------------------------------------------------------146
3-19. TFTP SERVER----------------------------------------------------------------------149
3-20. LOG-----------------------------------------------------------------------------------150
3-21. FIRMWARE UPGRADE--------------------------------------------------------------152
3-22. REBOOT -----------------------------------------------------------------------------153
3-23. LOGOUT------------------------------------------------------------------------------154
CHAPTER 4. OPERATION OF CLI MANAGEMENT---------------------------155
4-1. CLI MANAGEMENT-------------------------------------------------------------------155
4-1-1. Login ----------------------------------------------------------------------------155
4-2. COMMANDS OF CLI------------------------------------------------------------------157
4-2-1. Global Commands of CLI--------------------------------------------------158
4-2-2. Local Commands of CLI ---------------------------------------------------164
CHAPTER 5. MAINTENANCE--------------------------------------------------------253
5-1. RESOLVING NO LINK CONDITION --------------------------------------------------253
5-2. Q&A -----------------------------------------------------------------------------------253
APPENDIX A TECHNICAL SPECIFICATIONS -----------------------------------254
APPENDIX B NULL MODEM CABLE SPECIFICATIONS---------------------259

v
Revision History
Release Date Revision
0.92 10/04/2005 A1

vi

vii
Caution
Circuit devices are sensitive to static electricity, which can damage their delicate
electronics. Dry weather conditions or walking across a carpeted floor may cause you to
acquire a static electrical charge.
To protect your device, always:
•Touch the metal chassis of your computer to ground the static electrical charge before
you pick up the circuit device.
•Pick up the device by holding it on the left and right edges only.
Electronic Emission Notices
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a class A
computing device pursuant to Subpart J of part 15 of FCC Rules, which are designed to
provide reasonable protection against such interference when operated in a commercial
environment.
European Community (CE) Electromagnetic Compatibility Directive
This equipment has been tested and found to comply with the protection requirements
of European Emission Standard EN55022/EN60555-2 and the Generic European Immunity
Standard EN50082-1.
EMC:
EN55022(1988)/CISPR-22(1985) class A
EN60555-2(1995) class A
EN60555-3
IEC1000-4-2(1995) 4K V CD, 8KV, AD
IEC1000-4-3(1995) 3V/m
IEC1000-4-4(1995) 1KV – (power line), 0.5KV – (signal line)

Publication date: Oct., 2005
Revision A1
1
About this user’s manual
In this user’s manual, it will not only tell you how to install and connect your
network system but configure and monitor the 065-7726SPOE through the built-in
CLI and web by RS-232 serial interface and Ethernet ports step-by-step. Many
explanations in detail of hardware and software functions are shown as well as the
examples of the operation for web-based interface and command-line interface
(CLI).
Overview of this user’s manual
Chapter 1 “Introduction” describes the features of the 065-7726SPOE
Chapter 2 “Installation”
Chapter 3 “Operation of Web-based Management”
Chapter 4 “Operation of CLI Management”
Chapter 5 “Maintenance”

Signamax 

 065-7726SPOE 24-Port 10/100BaseT/TX
PoE Managed Switch User Manual
Publication date: Oct.., 2005
Revision A1
2
1. Introduction
1-1. Overview of the 065-7726SPOE
065-7726SPOE, a 24 Fast Ethernet + 2 Gigabit L2 Managed Switch,
implemented with 24 10/100Mbps TP + 2 Gigabit dual media ports with TP/SFP, is a
standard switch that meets all IEEE 802.3/u/x/z Gigabit, Fast Ethernet and Ethernet
specifications. The switch can be managed through a RS-232 serial port via direct
connection, or through an Ethernet port using Telnet or Web-based management
unit, associated with the SNMP agent. With the SNMP agent, the network
administrator can logon to the switch to monitor, configure and control each port’s
activity in a friendly way. The overall network management is enhanced and the
network efficiency is also improved to accommodate high bandwidth applications. In
addition, the switch features comprehensive and useful function such as QoS
(Quality of Service), Spanning Tree, VLAN, Port Trunking, Bandwidth Control, Port
Security, SNMP/RMON and IGMP Snooping capability via the intelligent software. It
is suitable for both metro-LAN and office application.
This PSE switch also complies with IEEE 802.3af, its advanced auto-sensing
algorithm enables providing power devices (PD) discovery, classification, current
limit, and other necessary functions. It also supports high safety with short circuit
protection and power-out auto-detection to PD.
• Model Description
Model Port 25, 26 Configurations
065-7726SPOE Two types of media --- TP and SFP Fiber
10/100/1000Mbps TP is a standard Ethernet port that meets all IEEE
802.3/u/x/z Gigabit, Fast Ethernet specifications. 1000Mbps SFP Fiber transceiver
is a Gigabit Ethernet port that fully complies with all IEEE 802.3z and 1000Base-
SX/LX standards.
1000Mbps Single Fiber WDM (BiDi) transceiver is designed with an optic
Wavelength Division Multiplexing (WDM) technology that transports bi-directional
full duplex signal over a single fiber simultaneously.
For upgrading firmware, please refer to the Section 3-21 or Section 4-2-2 for
more details. The switch will not stop operating while upgrading firmware and after
that, the configuration keeps unchanged.

Signamax 

 065-7726SPOE 24-Port 10/100BaseT/TX
PoE Managed Switch User Manual
Publication date: November, 2005
Revision A0.92
3
•
••
• Key Features in the Device
QoS:
Support Quality of Service by the IEEE 802.1P standard. There are two
priority queue and packet transmission schedule using Weighted Round
Robin (WRR). User-defined weight classification of packet priority can be
based on either VLAN tag on packets or user-defined port priority.
Spanning Tree:
Support IEEE 802.1D, IEEE 802.1w (RSTP: Rapid Spanning Tree
Protocol) standards.
VLAN:
Supports Port-based VLAN and IEEE802.1Q Tag VLAN. Supports 256
active VLANs and VLAN ID 1~4094.
Port Trunking:
Support static port trunking and port trunking with IEEE 802.3ad LACP.
Bandwidth Control:
Support ingress and egress per port bandwidth control.
Port Security:
Support allowed, denied forwarding and port security with MAC address.
SNMP/RMON:
SNMP agent and RMON MIB. In the device, SNMP agent is a client
software which is operating over SNMP protocol used to receive the
command from SNMP manager (server site) and echo the corresponded
data, i.e. MIB object. Besides, SNMP agent will actively issue TRAP
information when happened.
RMON is the abbreviation of Remote Network Monitoring and is a branch of
the SNMP MIB.
The device supports MIB-2 (RFC 1213), Bridge MIB (RFC 1493), RMON
MIB (RFC 1757)-statistics Group 1,2,3,9, Ethernet-like MIB (RFC 1643),
Ethernet MIB (RFC 1643) and so on.
IGMP Snooping:
Support IGMP version 2 (RFC 2236): The function IGMP snooping is used
to establish the multicast groups to forward the multicast packet to the
member ports, and, in nature, avoid wasting the bandwidth while IP
multicast packets are running over the network.

Signamax 

 065-7726SPOE 24-Port 10/100BaseT/TX
PoE Managed Switch User Manual
Publication date: Oct.., 2005
Revision A1
4
1-2. Checklist
Before you start installing the switch, verify that the package contains the
following:
A set of the 065-7726SPOE
Modules (optional)
Mounting Accessory (for 19” Rack Shelf)
This User's Manual in CD-ROM
AC Power Cord
RS-232 Cable
Please notify your sales representative immediately if any of the aforementioned
items is missing or damaged.
1-3. Features
The 065-7726SPOE, a standalone off-the-shelf switch, provides the
comprehensive features listed below for users to perform system network
administration and efficiently and securely serve your network.
•
••
• Hardware
• Supports 24-port 10/100M TP ports with Nway and auto MDIX function
• In 065-7726SPOEswitch, it supports 2 Gigabit dual media ports(TP/SFP) and 2
slots for removable SFP module supporting 1000M SFP fiber module
• Supports on-line pluggable fiber transceiver modules
•Supports 256KB packet buffer and 128KB control memory
• Maximal packet length can be up to 1536 bytes
• Full-duplex flow control (IEEE802.3x) and half-duplex backpressure
• Extensive front-panel diagnostic LEDs; System: Power, CPURUN, ACT / FDX /
SPD(LEDSET), 10/100Mbps TP Port1-24:LINK/ACT, FDX, SPD,
10/100/1000Mbps/Fiber port 25,26: LINK/ACT, FDX, SPD
24 port IEEE802.3af PoE PSE.
Endpoint with 48VDC power through RJ-45 pin 1, 2, 3, 6.
Powered Device (PD) auto detection and classification.
PoE-PSE status and activity LED indicator.

Signamax 

 065-7726SPOE 24-Port 10/100BaseT/TX
PoE Managed Switch User Manual
Publication date: November, 2005
Revision A0.92
5
•
••
• Management
•Supports concisely the status of port and easily port configuration
•Supports per port traffic monitoring counters
• Supports a snapshot of the system Information when you login
• Supports port mirror function
• Supports the static trunk function
• Supports 802.1Q VLAN with 256 entries.
• Supports user management and limits three users to login
• Supports DHCP Broadcasting Suppression to avoid network suspended or
crashed
• Supports to send the trap event while monitored events happened
•Supports default configuration which can be restored to overwrite the current
configuration which is working on via web browser and CLI
• Supports on-line plug/unplug SFP modules
• Supports 5 kinds of QoS, are as follows, MAC Priority, 802.1p Priority, IP TOS
Priority, and DiffServ DSCP Priority.
• Built-in web-based management and CLI management, providing a more
convenient UI for the user
• Supports port mirror function with ingress/egress traffic
•Supports rapid spanning tree (802.1w RSTP)
• Supports 802.1x port security on a VLAN
• Supports user management and only first login administrator can configure the
device. The rest of users can only view the switch
• SNMP access can be disabled and prevent from illegal SNMP access
• Supports Ingress, Non-unicast and Egress Bandwidth rating management
• The trap event and alarm message can be transferred via e-mail and mobile
phone short message
• Supports diagnostics to let administrator knowing the hardware status
•Supports external loopback test to check if the link is ok
• TFTP for firmware upgrade, system log upload and config file import/export
• Supports remote boot the device through user interface and SNMP
• Supports network time synchronization and daylight saving

Signamax 

 065-7726SPOE 24-Port 10/100BaseT/TX
PoE Managed Switch User Manual
Publication date: Oct.., 2005
Revision A1
6
• Supports 120 event log records in the main memory and display on the local
console

Signamax 

 065-7726SPOE 24-Port 10/100BaseT/TX
PoE Managed Switch User Manual
Publication date: November, 2005
Revision A0.92
7
1-4. View of the 065-7726SPOE
1-4-1. User Interfaces on the Front Panel (Button, LEDs and Plugs)
There are 24 TP Fast Ethernet ports and 2 slots for optional removable
modules on the front panel of the switch. LED display area, locating on the front
panel, contains a CPURUN, Power LED and 26 ports working status of the switch.
Fig. 1-1 Full View of the 065-7726SPOE
Fig. 1-2 Front View of the 065-7726SPOE
Power Indication LED
Fast
Ethernet Port
LED SET Mode: ACT/FDX/SPD
Gigabit Dual Media
Port (25~26):
SFP/TP
LEDSET Button
LEDSET button is
used to change
the LED display
mode
PoE Port Status
Indication LEDs
Fiber P
ort Status Indication LED
s
TP Port Status
Indication LEDs
RESET B
utton
:
RESET button is used to
reset the management
system.

Signamax 

 065-7726SPOE 24-Port 10/100BaseT/TX
PoE Managed Switch User Manual
Publication date: Oct.., 2005
Revision A1
8
•
••
• LED Indicators
LED Color Function
System LED
CPURUN Green Lit when CPU is on and good
POWER Green Lit when AC power is on and good
ACT Green Lit when LEDSET set on active mode
FDX Green Lit when LEDSET set on full-duplex mode
SPD Green Lit when LEDSET set on speed mode
10/100Mbps Ethernet TP Port 1 to 24 LED
LINK Green Lit when connection with remote device is good
Off when cable connection is not good
ACT/FDX/ SPD
Amber
(TP Port 1
to 24 LED)
a. LEDSET set on ACT (active) mode:
Blinks when any traffic is present
b. LEDSET set on FDX (full-duplex) mode:
Lit when full-duplex mode is active
Blinks when any collision is present
c. LEDSET set on SPD (speed) mode:
Lit when 100Mbps speed is active
Off when 10Mbps speed is active
PoE-PSE ACT Green Lit when PoE Power is active
10/100/1000Mbps Gigabit TP/Fiber Port 25, 26 LED
LINK Green Lit when connection with remote device is good
Off when cable connection is not good
FX Green Lit when Fiber port is active
Off when TP port is active
ACT/FDX/ SPD
Green
(Port 25,
26 LED)
a. LEDSET set on ACT (active) mode:
Blinks when any traffic is present
b. LEDSET set on FDX (full-duplex) mode:
Lit when full-duplex mode is active
Blinks when any collision is present
c. LEDSET set on SPD (speed) mode:
Lit when 1000Mbps speed is active
Off when 10/100Mbps speed is active
Table1-1

Signamax 

 065-7726SPOE 24-Port 10/100BaseT/TX
PoE Managed Switch User Manual
Publication date: November, 2005
Revision A0.92
9
1-4-2. User Interfaces on the Rear Panel
One RS-232 DB-9 interface is offered for configuration or management. And
there is one AC power input socket for having the switch powered on or off.
Fig. 1-3 Rear View of the 065-7726SPOE
RS
-
232 DB
-
9 Connector
AC Line 100
-
240V 50/60 Hz

Signamax 

 065-7726SPOE 24-Port 10/100BaseT/TX
PoE Managed Switch User Manual
Publication date: Oct.., 2005
Revision A1
10
1-5. View of the Optional Modules
In the switch, Port 25, 26 includes two types of media --- TP and SFP Fiber
(LC, BiDi LC…); this port supports 10/100/1000Mbps TP or 1000Mbps SFP Fiber
with auto-detected function. 1000Mbps SFP Fiber transceiver is used for high-
speed connection expansion; nine optional SFP types provided for the switch are
listed below:
1000Mbps LC, MM, SFP Fiber transceiver (SFP.0LC.202)
1000Mbps LC, SM 10km, SFP Fiber transceiver (SFP.0LC.212.10)
1000Mbps LC, SM 30km, SFP Fiber transceiver (SFP.0LC.212.30)
1000Mbps LC, SM 50km, SFP Fiber transceiver (SFP.0LC.212.50)
1000Mbps BiDi LC, type 1, SM 20km, SFP Fiber WDM transceiver
(SFP.0BL.621.201)
1000Mbps BiDi LC, type 2, SM 20km, SFP Fiber WDM transceiver
(SFP.0BL.621.202)
1000Mbps LC, SM 10km, SFP Fiber transceiver with DDM
(SFP.DLC.212.10)
Fig. 1-4 Front View of 1000Base-SX/LX LC, SFP Fiber Transceiver
Fig. 1-5 Front View of 1000Base-LX BiDi LC, SFP Fiber Transceiver