SignaMax 065-7111F Series User manual

SignamaxConnectivity Systems
065-7111F series
Compact Fiber Access Switch
U S E R ’ S G U I D E

SignamaxConnectivity Systems
065-7111F series
Compact Fiber Access Switch
User’s Guide

Signamax 

 065-7111F series Compact Fiber Access Switch
User’s Manual 1
Table of Contents
Table of Contents............................................. 1
Packing List ...................................................... 2
FCC Statement ................................................. 2
Introduction ...................................................... 3
Product Features........................................................ 3
Front Panel ................................................................ 3
LEDs.......................................................................... 3
Installation ........................................................ 4
Selecting a Site for the Switch.................................... 4
Connecting to Your Network....................................... 4
Specifications................................................... 5
Contact Information ......................................... 6

Signamax 

 065-7111F series Compact Fiber Access Switch
2User’s Manual
Packing List
Please inspect the contents and report any apparent damage or missing
items immediately to our authorized reseller.
The Signamax065-7111F series Compact Fiber Access Switch
User’s manual
One AC power cord
FCC Statement
The FCC (Federal Communications Commission) restricts the amount of
radio frequency emission and radiation coming from computer equipment.
The Ethernet switch stated in this manual has been tested and found to
comply with the limits for a Class A digital device pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user is required to correct the interference at
his/her own expense. Any changes or modifications not expressly approved
by the manufacture would void the user’s authority to operate the equipment.

Signamax 

 065-7111F series Compact Fiber Access Switch
User’s Manual 3
Introduction
The Signamax065-7111F series Compact Fiber Access Switch is an 8-port
Ethernet switch, integrating 10/100BaseTX (100BaseFX) networks in a
cost-effective compact size package. The TX ports can auto sense speed
and half/full duplex modes and auto-MDIX.
Product Features
7-port for 10/100BaseTX and 1-port for 100BaseFX.
The TX ports auto negotiate for 10/100Mbps speed, auto detect full/half
duplex mode, and auto-MDIX.
Choices of SC, ST, MT-RJ, VF-45, or LC connectors for FX ports.
Broadcast storming filter function.
True non-blocking architecture.
Full wire-speed forwarding rate.
Store-and-forward mechanism.
Back pressure and IEEE802.3x compliant flow control.
Supports 2K MAC addresses.
Supports 1M bits buffer memory.
Front panel power and port status LEDs.
Compact size.
Front Panel
The front panel of the switch has eight ports and an array of LED indicators to
provide you with instant feedback on the status of the switch.
LEDs
The array of LED indicators on the front panel conveys status and
configuration information to help you monitor and troubleshoot the switch.
Figure 1: Front & rear panels
Power This LED comes on when the switch is connected to the power.


Port Status Each port has a LED, indicating the port status.
Power Adapter Connect the supplied AC power cord to the receptacle
on the back of the switch, then plug the cord into a standard AC outlet with a
voltage range from 100 to 240 VAC.

Signamax 

 065-7111F series Compact Fiber Access Switch
4User’s Manual
Table 1: Port Status
LED State Indication
Steady The port has established a valid network connection.
LNK stands for LINK.LNK/
ACT Flashing The port is transmitting or receiving data.
ACT stands for ACTIVITY.
Installation
Selecting a Site for the Switch
As with any electronic device, you should place the switch where it will not be
subject to extreme temperatures, humidity, or electromagnetic interference.
Specifically, the site you select should meet the following requirements:
The ambient temperature should be between 32 and 104 degrees
Fahrenheit (0 to 40 degrees Celsius).
The relative humidity should be less than 90 percent, non-condensing.
Surrounding electrical devices should not exceed the electromagnetic
field (RFC) standards for IEC 801-3, Level 2 (3V/M) field strength.
Make sure that the switch receives adequate ventilation. Do not block
the ventilation holes on the side of the switch or the fan exhaust port on
the rear of the switch.
The power outlet should be within 6 feet (1.8 meters) of the switch.
Connecting to Your Network
Connect network cables from computers or network segments to the TX (FX)
ports on the back of the unit.
Table 2: Cabling Information
Speed Connector Port Speed
Half/Full Duplex
Cable
100BaseTX RJ-45 100/200 Mbps 100 m, Category 5 or better
STP/UTP
10BaseT RJ-45 10/20 Mbps 100 m, Category 3, 4, 5 or
better STP/UTP
100BaseFX
multimode
SC, ST,
MT-RJ,
VF-45, or LC
100/200 Mbps Up to 2 km, 50 or 62.5/125 µm
multimode fiber cable
100BaseFX
singlemode SC 100/200 Mbps Up to 75 km, 9 or 10/125 µm
singlemode fiber cable

Signamax 

 065-7111F series Compact Fiber Access Switch
User’s Manual 5
Specifications
Applicable Standards IEEE 802.3, 10BaseT,
IEEE 802.3u, 100BaseTX/FX
LED Indicators Per unit – Power Status
Per Port – LNK/ACT
Cable 10BaseT 2-pair UTP/STP Cat. 3,4,5 or better, up to 100m
100BaseTX 2-pair UTP/STP Cat.5 or better, up to 100m
100BaseFX 50 or 62.5/125µm multi
mode fiber optic cable,
up to 2km
100BaseFX 9 or 10/125 µm singlemode fiber optic cable,
up to 75 km (distance spanned is model-dependent)
Switching Methods Store-and-Forward
Forwarding Rate 14,880 packets per second for 10 Mbps,
148,800 packets per second for 100 Mbps
AC Input 100 ~ 240 V AC, 50 - 60 Hz.
Power consumption 3.3 V DC, 2.5 A, 8.25 Watts maximum
Operating
Temperature
32°F ~ 104°F (0°C ~ 40°C)
Storage Temperature -13°F ~ 158°F (-25°C ~ 70°C)
Humidity 10%~90%, non-condensing
Emissions FCC part 15 Class A, CE Mark
Dimensions 10.0 x 5.3 x 1.4 inches [W x D x H] (254 x 135 x 35 mm)
Weight 3.5 lb. (1.6 kg)

Signamax 

 065-7111F series Compact Fiber Access Switch
6User’s Manual
Contact Information
SIGNAMAX

CONNECTIVITY SYSTEMS
An AESP Company
1810 N.E. 144th Street.
North Miami, Florida 33181, U.S.A.
Phone: [phone] Fax: [phone]
Sales: 800-446-2377 Tech. Support: 800-446-2377, ext. 201
Http://www.signamax.com
E-mail: [email protected]
EUROPE
AESP Ukraine. (UKRAINE)
2 Timiryazevskaya St. 47
252014 Kiev, Ukraine
Phone: [phone]
Fax: [phone]
Http://www.aesp.com.ua
E-mail: [email protected]
AESP Sweden. (SWEDEN)
Grevegatan 19-21 SE-815
40 TIERP. SWEDEN
Phone: [phone]
Fax: [phone]
Phone: [phone]
Http://www.aesp.se
E-mail: [email protected]
JOTEC AESP AS. (NORWAY)
Telefon [phone] Ordrefax
23 14 17 10 Karihaugveien 102
Postboks 50 Ellingsrudasen
1006 Oslo, Norway
Phone: [phone]
Fax: [phone]
Http://www.jotec.no
E-mail: [email protected]
AESP Russia. (RUSSIA)
Kronshtadtsky Blv.
125499 Moscow, Russia
Phone: [phone]
Phone: [phone]
Fax: [phone]
Http://www.aesp.ru
E-mail: [email protected]
AESP Germany GmbH
(GERMANY)
Weisserfelderstr.2 D-85551
Kircheim b. München, Germany
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
INTELEK spol.s.r.o
(CZECH REPUBLIC)
Vlarska 22,
Brno, CZ 62700
CZE Czech Republic
Phone: [phone]
Fax: [phone]
Http://www.intelek.cz
E-mail: [email protected]