Signtex Lighting Moonlite LED MAE-AC-20 Series Quick start guide

1. Disconnect AC power before servicing.
2. Refer to wiring diagram for proper connections.
3. All servicing should be performed by qualified personnel.
4. Consult your local building code for approved wiring and installation.
5. Do not use this equipment for other than intended use.
6. Do not let power cords touch hot surfaces.
7. Mount and secure the fixture at a location and height to avoid ready access
and tampering by unauthorized persons.
8. The use of accessory equipment is not recommended by the manufacturer
and may cause an unsafe condition.
9. Suitable for wet locations. See product label for temperature limitations.
IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
SUITABLE FOR WET LOCATIONS
AMBIENT TEMPERATURE LIMITS:
Standard models: -20º C to +40º C
Remote models: -40º C to +50º C
J- Box and Supply Wiring
1. See above for available K.O.'s for wiring connectors. Select K.O.'s for AC input wiring. Install standard
4” x 4” deep j-box with 1 ½” extension.
IMPORTANT: SET J-BOX ASSEMBLY TO ALIGN EDGE OF EXTENSION FLUSH OR JUST
BELOW FINISH PANEL SURFACE.
2. See above. Insert Power Supply Assembly (1) into j-box and secure with two #8-32 x ½” screws.
3. See above. Connect AC input wiring from power supply assembly to building supply with wire nuts,
with Ground connector to j-box: BROWN: 120-277 VAC: BLUE: Neutral.
AVAILABLE K.O.'S
4 PLACES
SET EDGE OF BOX
FLUSH TO WALL
FINISH OR
PANEL THICKNESS
STANDARD J-BOX
4 x 4 x 21/8"
EXTENSION RING
4 x 4 x 11/2"
INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL
LED Architectural Emergency Light
Series MAE-AC-20
Moonlite LED™
Universal 120/ 277 VAC Supply
04.16.02
EXTENSION
RING 1 1/2"
L N G
120/277 VAC
J-BOX
4 x 4 x 2 1/8" GROUND
TO J-BOX
L B
N W
LAMP PLUG
(2) # 8-32 x 1/2
J-BOX MOUNT
SCREWS
1

-2-
220 VFW Avenue, Grasonville, MD 21638
TEL: (410) 827-- 8300 Fax:[phone]
[e-mail] www.signtexinc.com
Signtex Inc
LIGHTING
Fixture Assembly
1. Loosen the (2) #6-32 set screws to release housing from Canopy.
2. Run polarized Lamp Plug from power supply through Canopy/ Gasket (2).
3. Route Lamp Plug through Canopy Assembly; locate Canopy in position. Secure with two #8-32 x
1/2” screws and tighten evenly.
4. Connect Lamp Plug from Housing (4).
5. Gently insert plug assembly and wiring sleeve through the gasket into j-box, locate Housing and
Gasket in position and secure with two #6-32 x 3/8” set screws.
6. Turn on AC supply to operate.
ITEM QTY P/N DESCRIPTION
1 1 346600 POWER SUPPLY ASSBY
2
3
4
1
1
1
346202
346302
346501
GASKET
CANOPY
HOUSING ASSBY
Moonlite LED™
Universal 120/ 277 VAC Supply
04.16.02
LED Architectural Emergency Light
Series MAE-AC-20
TOP MT
(OPTION)
BLACK- LINE
WHITE- NEUTRAL
GROUND
TO J-BOX (2) # 8-32 x 1/2
J-BOX MOUNT
SCREWS
L
N
1(2) # 6-32 x 1/2
CANOPY MOUNT SCREW
POLARIZED
LAMP PLUG
2- PIN
WIRING
SLEEVE
4
2
3