Signtex Lighting EMP Series User manual

UNIVERSAL BACK, END OR TOP MOUNT FOR SINGLE AND DOUBLE FACE SIGNSUNIVERSAL BACK, END OR TOP MOUNT FOR SINGLE AND DOUBLE FACE SIGNS
BACK MOUNT:
1- Select arrows as required by removing arrow insert(s) in stencil face sheet legend. Remove plastic protector from
window. Discard angle bracket.
2- ENSURE MOUNTING SURFACE IS FLAT WITH NO RAISED AREAS THAT MAY PENETRATE SIGN OR
CAUSE BENDING. Use sign to mark mounting points, and mount sign in position using maximum size 8 screws.
Up to six screws may be used (mounting screws supplied by installer).
3- Replace legend and window. Window snaps into housing by locating tabs at six points as shown. Place into position
by locating two bottom tabs. Bend the window outwards slightly at sides to insert side tabs. Two tabs along top edge
may be inserted by flexing wall (EMP models only) or by inserting 1/4" scewdriver, twist to insert tabs {EMA & EMP
models). To remove window, insert flat screwdriver into slots provided and twist to release tabs at two points on top
edge, then flex window to remove.
WINDOW LOCK TABS
AT SIX POINTS
WINDOW LOCK TABS
AT SIX POINTS
SCREWDRIVER RELEASE SLOTSSCREWDRIVER RELEASE SLOTS
DOUBLE FACEDOUBLE FACE
Emergence
Self- Luminous Signs
Thermoplastic Housing
Series EMP & EMC
LOCK
WASHER
OUTER
WINDOW
STENCIL FACE
SPECIFIED EMERGENCY LIGHTINGSPECIFIED EMERGENCY LIGHTING
Signtex Inc
LIGHTING
SINGLE FACE
TOP MOUNTTOP MOUNT BACK MOUNTBACK MOUNT
See diagrams below:
1. Select open holes (not tapped holes), place bracket in mount position and mark screw anchor locations
on ceiling or wall surface. Install screw anchors, and install bracket.
2. Attach sign to bracket using two #8-32 Allen- Head screws with lock washers provided.
UNIVERSAL TOP OR END MOUNTUNIVERSAL TOP OR END MOUNT

1. Assemble Angle Bracket to Canopy
Plate using 2 # 8-32 x 1/2" screws,
nuts, & washers.
2. If mounting direct to wall or ceiling,
use Canopy Plate holes to mark screw
anchor and clearance hole positions,
drill and insert anchors.
3. Mount Canopy Plate to selected location
using screws supplied.
4. Assemble sign to bracket using 2 #8 screws
provided.
5. Select arrows ; replace legend and window-
see over.
8-32 X 1"
SCREWS TO SURFACE
OR BOX
#8 BRACKET SCREWS
WINDOW
Emergence
Self- Luminous Signs
Thermoplastic Housing
Series EMP & EMC
SPECIFIED EMERGENCY LIGHTINGSPECIFIED EMERGENCY LIGHTING
Signtex Inc
LIGHTING
1. Assemble Angle Bracket to Canopy
Plate using 2 # 8-32 x 1/2" screws,
nuts, & washers.
2. If mounting direct to wall or ceiling,
use Canopy Plate holes to mark screw
anchor and clearance hole positions,
drill and insert anchors.
3. Mount Canopy Plate to selected location
using screws supplied.
4. Assemble sign to bracket using 2 #8 screws
provided.
5. Select arrows ; replace legend and window-
see over.
8-32 X 1"
SCREWS TO SURFACE
OR BOX
#8 BRACKET SCREWS
WINDOW
Emergence
Self- Luminous Signs
Thermoplastic Housing
Series EMP & EMC
SPECIFIED EMERGENCY LIGHTINGSPECIFIED EMERGENCY LIGHTING
Signtex Inc
LIGHTING
1. Assemble Angle Bracket to Canopy
Plate using 2 # 8-32 x 1/2" screws,
nuts, & washers.
2. If mounting direct to wall or ceiling,
use Canopy Plate holes to mark screw
anchor and clearance hole positions,
drill and insert anchors.
3. Mount Canopy Plate to selected location
using screws supplied.
4. Assemble sign to bracket using 2 #8 screws
provided.
5. Select arrows ; replace legend and window-
see over.
8-32 X 1"
SCREWS TO SURFACE
OR BOX
#8 BRACKET SCREWS
WINDOW
Emergence
Self- Luminous Signs
Thermoplastic Housing
Series EMP & EMC
SPECIFIED EMERGENCY LIGHTINGSPECIFIED EMERGENCY LIGHTING
Signtex Inc
LIGHTING
1. Assemble Angle Bracket to Canopy
Plate using 2 # 8-32 x 1/2" screws,
nuts, & washers.
2. If mounting direct to wall or ceiling,
use Canopy Plate holes to mark screw
anchor and clearance hole positions,
drill and insert anchors.
3. Mount Canopy Plate to selected location
using screws supplied.
4. Assemble sign to bracket using 2 #8 screws
provided.
5. Select arrows ; replace legend and window-
see over.
8-32 X 1"
SCREWS TO SURFACE
OR BOX
#8 BRACKET SCREWS
WINDOW
Emergence
Self- Luminous Signs
Thermoplastic Housing
Series EMP & EMC
SPECIFIED EMERGENCY LIGHTINGSPECIFIED EMERGENCY LIGHTING
Signtex Inc
LIGHTING
DOUBLE FACE
SINGLE FACE
2 3/4"
4"
CANOPY
LOCATION
CLEARANCE
HOLES 3/8" DIA
SCREW ANCHOR
LOCATIONS-
DIA AS REQUIRED
DRILL LOCATIONS
CANOPY, TOP, OR END MOUNTCANOPY, TOP, OR END MOUNT
OUTER WINDOW
CANOPY PLATE
#8-32 x 3/8"
ALLEN HEAD
SCREWS &
LOCKWASHER
2 REQUIRED #8-32 x 3/4"
SCREWS
2 REQUIRED
3/8" DIA CLEARANCE HOLES (2 REQD.)
LEGEND