Sigtronics S-40H User manual

igtronics
®
Sigtronics
®
S
…when it counts!
Sigtronics Corporation
178 East Arrow Highway
San Dimas, CA 91773
Phone: [phone]
E-mail: [e-mail]
Web Site: www.sigtronics.com
Model S-40H
Headset Instructions
The S-40H series headsets are adjusted at the factory for immediate use with all
standard general aviation radio systems utilizing the U174/U jack. Headsets are
equipped with a coiled cable and a single U174/U plug conguration.
The headband is adjustable through a full range of motion, or the locking nuts
may be tightened to allow you to custom t the headset. Place the headset over
your head, adjust the slides up until minimum pressure is felt on the top of your
head. The headset is now properly adjusted. For maximum noise attenuation, the
clamping pressure has been set at the factory. Releasing the clamping pressure
by bending the headband is not advised, because loss of attenuation will result.
Note: If especially small (children) or large headbands are needed, they may be
ordered from Sigtronics.
The microphone boom is fully adjustable and will rotate 360 degrees for use on
the left or right side of the head. The locking screw that secures the boom to the
ear cup is factory set to insure the correct tension. Turning it will not change the
tension, because the nut on the inside of the cup will turn as well. Microphone
placement should be at the corner of the mouth, approximately ¼” from the
lips. The exclusive thumbscrew on the mic boom may be used to assure proper
adjustment.
When you rst connect the headset, turn the volume control on the headset up
to the full clockwise position, then adjust the listening volume with the audio
control of either your radio or intercom as appropriate. Passengers should also
turn their individual headset volumes up fully. Doing this allows for a full range of
adjustment for each passenger, since those with the most acute hearing can turn
their headset volume down, if necessary.
continued on back…
The headset parts may be cleaned with mild soap and water using a soft cloth.
Then dry immediately. Caution: Do Not immerse any part of the headset in water
or any other liquid. Be especially careful not to allow the microphone to become
wet! Exposure to moisture may cause internal corrosion and failure and will void
your manufacturers warranty.
Cleaning will help the headset maintain its “like new” condition for many years.
WINDSCREEN
The microphone windscreen will reduce annoying wind noise and breath pops
picked up by headset microphones. It also protects the microphone element
from dirt and moisture. The windscreen should be washed regularly to maintain
hygiene and avoid clogging. Wash in warm water and mild soap. Rinse thoroughly
and make sure it is completely dry before putting it back on.
To remove the windscreen, take out the screw that holds the microphone on the
boom and grasp the windscreen lightly along its entire length and slip it o.
Put the windscreen on the microphone by gently pulling from the open end. Do
not pull it so tightly that it stretches against the end of the microphone.
WARRANTY
Your headset is covered by a limited three-year parts and labor warranty. Please
see the enclosed warranty card for details.
You may refer to the parts list on the reverse side, if you choose to replace parts
yourself. The parts list describes parts for this particular headset only. Parts lists
for other models are available on our Web Site or can be obtained by contacting
Sigtronics Corporation.

SIGTRONICS S-40H HEADSET PARTS IDENTIFICATION BREAKDOWN
ITEM P/N DESCRIPTION ITEM P/N DESCRIPTION ITEM P/N DESCRIPTION
1800145 HEADBAND , WITH CUSHION, S-40 15 100937 EAR CUP, PRINTED AND DRILLED, MICROPHONE SIDE 29 800046 CABLE, HEADSET, HELICOPTER, COILED
2100383 HEADBAND, METAL, STANDARD 16 100938 EAR CUP, PRINTED AND DRILLED, VOLUME CONTROL SIDE 30 800039 CABLE, MICROPHONE BOOM, 12 INCH
3100367 YOKE, EAR CUP MOUNT, METAL 17 100049 GROMMET, 5/16 INCH, RUBBER 31 100933 WIRE, CROSSOVER, OVER THE HEAD, 28 INCH
4100384 BRACKET, YOKE SUPPORT WITH TANG 18 M-80H MICROPHONE, ELECTRET, M-80H 32 100935 WIRE, #22, JUMPER, HEADSET, 4 INCH
5100373 SLIDE, YOKE BRACKET, LONG, NYLON 19 900084 WINDSCREEN, MICROPHONE 33 100569 STRAIN RELIEF, CABLE
6100258 CLIP, HEADBAND GUIDE, PLASTIC 20 100249 BOOM, ELECTRET MICROPHONE SUPPORT, SWIVEL 34 100371 MICROPHONE CABLE CLIP
7100393 CLIP, ANTI-ROTATION, YOKE, PLASTIC 21 100156 SCREW, THUMB, MICROPHONE BOOM, 2-56 X 1 35 100360 KNOB, BLACK, VOLUME
8100362 CLIP, CROSS-OVER, WIRE, PLASTIC 22 100368 KNOB, MICROPHONE BOOM ADAPTER, PLASTIC 36 100365 POTENTIOMETER, 2K
9100363 SCREW, 8-32 X 1/2, PHILLIPS HEAD 23 100408 WASHER, GROOVED BOOM 37 100858 RECEIVER AND MOUNT, 300 OHM, MONO
10 100364 SCREW, 8-32 X 3/8, PHILLIPS HEAD 24 100385 WASHER, SPRING, BOOM ADAPTER 38 100618 OPTIONAL – HEADBAND, METAL, YOUTH
11 100377 SCREW, 8-32 X 5/8, PHILLIPS HEAD 25 100369 EAR SEAL, FOAM FILLED 39 100257 OPTIONAL – HEADBAND, METAL, LARGE
12 100108 SCREW, 4 X 1/4, THREAD FORMING 26 100374 FOAM, SOUND ATTENUATING. NOTCHED, 1/2 INCH 40 100402 OPTIONAL – EAR SEAL, GEL FILLED
13 100251 E-RING, EAR CUP TO YOKE RETAINER 27 100376 FOAM, SOUND ATTENUATING. RECEIVER HOLE, 1/2 INCH
14 100252 NUT, HEX, 8-32, LOCKING 28 100379 FOAM, SOUND ATTENUATING, RECEIVER COVER, 1/4 INCH











































10-4-2021
s-40h.pdf