SIIG JU-CSL111-S1 User manual

USB 3.0 Data KM Magic
Switch Console Cable
User manual
P/N: JU-CSL111-S1

MAGIC SWITCH User Manual
2
SYSTEM REQUIREMENTS
Windows
OS: Windows 10 / 8.1 / 7 (SP1) (32/64 bit)
Available USB port: USB3.0 is recommended
Use USB3.0 Host: Fresco FL1000 / FL1009 install additional Host Driver
USB Host not supported: Asmedia, Etron 168 / 188, Via 801/ Via 805
CPU: Intel Pentium IV Processor or later
RAM: 1G or above
Hard Disc Capability: at least 100MB
Mac
Mac OS X 10.14/10.13/10.12/10.11/10.10
Available USB port: USB3.0 is recommended
CPU: Intel Pentium IV Processor or later
RAM: 1G or above
Hard Disc Capability: at least 100MB
Notes
※Windows RT not supported.
※On Windows Vista，restart your computer after the initial installation.
※Virtual Windows or Mac OS by VMware is not supported.
※The computer/user needs to have administrator rights.
※If one of the two connected computers restarts, reboots, sleeps or hibernates, please
disconnect and reconnect both sides of the Magic Switch.

MAGIC SWITCH User Manual
3
Windows installation
Please follow the instructions below to install the Magic Switch driver.
1. Connect one end of the Magic Switch to a standard USB port on one of the two computers.
And connect the other end of the Magic Switch to aUSB port on thesecond computer.
2. The device willautomatically start the Magic Switch software installation on both
computers. An AutoPlay option window may appear. Please double-click the Magic
Switch icon to start the application.
3. If the User Account Controlwindow appears on the screen, click Yes to continue.
4. Please run the steps above on both computers. If the other computer is a Mac, please refer
to the Mac installation guide.
5. When the Magic Switch is connected properly the Magic Switch launch page will be
shown.
The Magic Switch icon will appear in the lower right-hand corner. If the two units are
connected to the USB3.0 port this icon will appear, indicating the transmission speed as
USB3.0; however, if a USB2.0 port is connected to one end, then this icon will appear,
indicating that the transmission speed is USB2.0. If the icon appears it means the other
computer is not connected. When this icon appeared means the keyboard & mouse is
under controlled by other computer.
6. Please set the position of the other PC. Please click on the Magic Switch or icon to
open the Magic Switch toolbar. Then click on The Position of Other PC and select the
screen location according to where you want your mouse to flow from one screen to the
other.

MAGIC SWITCH User Manual
4
Mac installation
Please follow the instructions below to install the Magic Switch driver.
1. Connect one end of the Magic Switch to a standard USB port on one of the two
computers. And connect the other end of the Magic Switch to aUSB port on the second
computer.
2. When you initially connect the Magic Switch to the MAC computer the Keyboard Setup
Assistant window may pop up, follow the steps to select the keyboard type.
3. When both ends of the Magic Switch plugged into the computers’ USB ports, the Magic
Switch drive will appear on the desktop, double-click Magic Switch icon to
start the software.If the Enable access for
assistive devices window appears on the screen,
click Yes to continue.
4. Please run the steps above on both computers. If the other computer is a Windows, please
refer to the Windows installation guide.
5. When the Magic Switch is connected properly the Magic Switch launch page will be
shown.
The Magic Switch icon will appear in the lower right-hand corner. If the two units are
connected to the USB3.0 port this icon will appear, indicating the transmission speed
as USB3.0; however, if a USB2.0 port is connected to one end, then this icon will appear,
indicating that the transmission speed is USB2.0. If the icon appears it means the
other computer is not connected.
6. Please set the position of the other PC.Please click on the Magic Switch or icon to
open the Magic Switch toolbar. Then click on The Position of Other PC and select the
screen location according to where you want your mouse to flow from one screen to the
other.

MAGIC SWITCH User Manual
5
Functions:
Explore the Magic Switch’s convenient and user-friendly features.
9Keyboard and Mouse Sharing
Move your mouse cursor between two computers naturally and seamlessly.
9ɈPlease use a keyboard and mouse set.(The keyboard switch function always applies to
the computer the mouse is currently on).
9Switch the keyboard usage to another computer
Move the mouse cursor to the second computer and open any editing application such
as Word, Excel, Power Point, etc. and use the keyboard of the first computer to type the
text on the file of the second computer.
9Clipboard Sharing
With the clipboard sharing feature you can easily copy and paste clipboard content
bi-directionally between two computers.
9File Transferring
Quickly and easily transfer files between two computers. Simply copy/paste or
drag/drop the file or folder to the other computer.
9ɈPlease use the original system hotkey settings on your computer operating system (the
keyboard always follows the mouse cursor).

MAGIC SWITCH User Manual
6
SOFTWARE INSTRUCTIONS
To begin set up, please click the Magic Switch utility icon or , found on both Mac OS &
Windows OS.
MAC OS:
Windows OS:
9The Position of the Other PC烉You can quickly set up the position of the other computer by
using one of the 4 options (Right/Left/Up/Down)
9Temporarily Disable/Enable the keyboard/mouse and/or clipboard sharing function烉You
can quickly disable or enable the sharing option.
9Preference Setup
MAC OS Windows OS:
3Keyboard and Mouse Control Switch Settings烉
¾Off: Turns the mouse/keyboard sharing option off.
¾Use the Mouse to Move off the Edge of the Screen烉You can adjust your
settings so that your mouse moves from one computer’s screen to the other
computer’s screen from either the right/left/up/down side of the PC.
¾Use only the Hotkey to switch烉You can setup the hotkey to activate the
keyboard/mouse control switch. The default hotkey is (Alt+S)
3Clipboard Share Options烉Turn Off or Auto Share

MAGIC SWITCH User Manual
7
3Others烉
¾Show Connection Information烉Un-checking this setting means the launch page will
not be shown when you start up the device.
ɈThis option is only available on Mac OS computers.
¾Resident this Application烉When you choose this setting the Magic Switch program
automatically setsup every time you connect the Magic Switch device.
¾Enable Access for System Hotkey烉Choose this setting to activate the Hotkey function.
ɈThis option is only available on Mac OS computers.
¾Double Click the System Tray Icon to Turn Sharing On/Off Temporarily烉Enable/disable
the clipboard sharing and keyboard/mouse control functions by simply double clicking
the icon on the bottom right-hand side of the taskbar.
ɈThis option is only available on Windows OS computers.
¾Send Ctrl-Alt-Del to another computer烉This option allows for alternative key options
for the [Ctrl-Alt-Del]command for the second computer.
ɈThis function is only available when 2Windows OS computersare connected.
9Online Update烉Check and update the latest version of software for the Magic Switch.
1. Please make sure you are connected to the internet and Do Not disconnect the
Magic Switch during the driver update.
2. Remove the Magic Switch cable from the slave computer.
3. Select Online Update
4.After you have finished the installation process,disconnect and then reconnect
the Magic Switch device on both computers.
9About Magic Switch:Software version information can be found here.
9Quit USB Switch/ Exit:The Magic Switch can be uninstalled in the confirmation box.

Magic Switch compability issue on macOS 10.14
We have tested our Magic Switch on the official release of macOS 10.14 Mojave and we have
confirmed that this device is compable with the newest macOS operang system. However, we
have found that you may need to allow the Magic Switch applicaon on macOS 10.14.
Please follow these steps below:
1.) Please unplug the Magic Switch first
2.) Open System Preferences→Click on
Security & Privacy →Click on the Privacy
tab.
3.) Plug-in the Magic Switch. When the
system appears "Accessibility Access
(Events)" press "Open System Preferences"
4.) Click on “Click the lock to prevent further
changes" and key in your mac password to
make change.
5.) Check-Mark the box next to
GoBridgeDaemon or Magic Switch
7.) Click the lock again to save the changes.