SIIG 1 FireWire 800 CardBus DV-Ki User manual

1
04-0442D
FireWire 800 ExpressCard
Quick Installation Guide
Introducing the FireWire 800 ExpressCard
The FireWire 800 ExpressCard adds FireWire 800 (1394b)
interface to your ExpressCard equipped computer.
FeaturesandBenefits
• Provides 1 FireWire 800 (9-pin) and 1 FireWire 400
(6-pin) ports for multiple device connections
• Supports data transfer rates up to 800Mb/s
• Supportshot-swappingandPlug-n-Playconnection
of peripheral devices
• Works with FireWire devices including DV
camcorders, CD-RW/DVD-ROM drives, portable
hard disks, digital cameras and other audio/video
devices
SystemRequirements
• ExpressCard-enablednotebookPCwithanavailable
ExpressCard/54 slot
• Windows®7 (32-/64-bit) / Vista (32-/64-bit) / XP
(32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / 2000
PackageContents
• FireWire 800 ExpressCard
• Driver CD
• Quick installation guide

2
Layout
Figure 1. Layout
*Note: FireWire devices that have their own power
supply do not require the optional power adapter
to be connected in order to work. However,
non-poweredFireWiredevicesrequirethis optional
power adapter to work. The power adapter can be
purchasedatSIIG'sOnlineStore,part#NN-ADA011.
Hardware Installation
General instructions for installing the card are provided
below. Since the design of notebook computers may
vary, refer to your system’s reference manual for further
information, if needed.
Insert the ExpressCard into the ExpressCard/54 slot of
your notebook computer. Make sure it is inserted all the
way in for a solid connection.
Power Adapter Jack*
FireWire 400 port
(6-pin)
FireWire 800 port
(9-pin)
Power LED

3
Driver Installation
This section provides information on how to install the
FireWire 800 ExpressCard drivers.
Windows7(32-/64-bit)
Windows 7 automatically installs it's built-in FireWire
400 driver for the FireWire 800 ExpressCard. To get the full
speed out of this controller,install the FireWire 800
driver using the directions below.
1. Insert the driver CD, at the AutoPlay box, click Open
folder to view files.
For 32-bit: Double click setup32.
For 64-bit: Double click setup64.
2. Follow the on screen instructions to complete the
installation.
WindowsVista(32-/64-bit)
WindowsVista automatically installsit'sbuilt-inFireWire
400 driver for the FireWire 800 ExpressCard. To get the full
speed out of this controller,install the FireWire 800
driver using the directions below.
1. Insert the driver CD. Click Start.
For 32-bit: In the Start Search box, type
D:\setup32.exe, press Enter. (Change D: to match
your CD-ROM drive letter)
For 64-bit: In the Start Search box, type
D:\setup64.exe, press Enter. (Change D: to match
your CD-ROM drive letter)
2. Follow the on screen instructions to complete the
installation.

4
WindowsXP(32-/64-bit)
Windows XP automatically installs it's built-in 1394a
driver for the FireWire 800 ExpressCard. To get the full
speed out of this controller,install the FireWire 800
driver using the directions below.
1. Insert the driver CD. Click Start, Run.
For 32-bit: Type D:\setup32.exe, click OK. (Change
D: to match your CD-ROM drive letter)
For 64-bit: Type D:\setup64.exe, click OK. (Change
D: to match your CD-ROM drive letter).
2. Follow the on screen instructions to complete the
installation.
WindowsServer2003(32-/64-bit)
Windows Server 2003 automatically installs it's
built-in FireWire 400 driver for the FireWire 800
ExpressCard. To get the full speed out of this controller,
install the FireWire 800 driver using the directions below.
1. Insert the driver CD. Click Start, Run.
For 32-bit: Type D:\setup32.exe, click OK. (Change
D: to match your CD-ROM drive letter)
For 64-bit: Type D:\setup64.exe, click OK. (Change
D: to match your CD-ROM drive letter)
2. Follow the on screen instructions to complete the
installation.

5
WindowsServer2008(32-/64-bit)
Windows Server 2008 automatically installs it's built-in
FireWire 400 driver for the FireWire 800 ExpressCard. To
getthefull speed out of this controller,install the FireWire
800 driver using the directions below.
1. Insert the driver CD. Click Start.
For 32-bit: In the Start Search box, type
D:\setup32.exe, press Enter. (Change D: to match
your CD-ROM drive letter)
For 64-bit: In the Start Search box, type
D:\setup64.exe, press Enter. (Change D: to match
your CD-ROM drive letter)
2. Follow the on screen instructions to complete the
installation
Windows2000
Windows 2000 automatically installs it's built-in 1394a
driver for the FireWire 800 ExpressCard. To get the full
speed out of this controller, install the FireWire 800
driver using the directions below.
1. Insert the driver CD. Click Start, Run. Type
D:\setup32.exe, click OK. (Change D: to match
your CD-ROM drive letter)
2. Follow the on screen instructions to complete the
installation.
ToVerifyWindowsInstallation
1. Check Device Manger to verify installation.
For Windows 7 / XP / Server 2003 / 2000: Right click
Computer or My Computer, click Manage, then
click Device Manager.

6
For Windows Vista: Right click Computer, click
Manage, click Continue, click Device Manager.
For Windows Server 2008: Right click Computer,
click Manage, double click Diagnostics, click
Device Manager
2. Double click 1394 Bus host controllers. Unibrain
driver/OHCI Compatible Board or IEEE 1394b
(FireWire 800) adapter should be displayed.
Connecting Devices
General driver installation steps are provided below.
Please review your device's user manual for more details.
Windows 7 / Vista / Server 2008
Windows 7, Windows Vista, or Server 2008 will
automatically detect and install most FireWire devices
when connected. However, for devices that do not install
automatically, additional drivers maybe required. Refer
to the device's users manual and/or contact the device's
manufacturer for the correct driver.
WindowsXP
1. At the Found New Hardware Wizard.
For XP w/SP2 or later: Select No, not this time, then
click Next.
For XP w/SP1 or earlier: Go directly to step #2.
2. SelectInstalltheSoftwareAutomatically,clickNext.
3. Click Continue Anyway. (Skip if not prompted)
4. Click Finish to complete the installation.

7
WindowsServer2003
1. At the Found New Hardware Wizard.
For Server 2003 w/SP1 or later: Select No, not this
time, then click Next.
For Server 2003: Go directly to step #2.
2. SelectInstalltheSoftwareAutomatically,clickNext.
3. At the Security Alert box click Yes, or the Hardware
Installation box click Continue Anyway, then click
Finish to complete the installation.
Windows2000
1. At the Found New Hardware Wizard, click Next.
2. SelectSearch for a suitable driver ..., then click Next.
3. Uncheck all check boxes, click Next, click Next.
4. Click Finish to complete the installation.
Removing the ExpressCard
Stop the ExpressCard before removing it from the
ExpressCard slot.
1 The utility is located in the taskbar by the system
clock. Click the Unplug or Eject Hardware or
Safely Remove Hardware icon. Click Remove PCI
standard PCI-to-PCI bridge.
2. Wait for the confirmation box, then remove the
ExpressCard from the ExpressCard slot.

8
ubSwitch Utility
In order to use a DV camcorder with this controller,
Microsoft's FireWire 400 driver must be installed in the
system. We have supplied an easy to use utility that
allows switching between Microsoft's driver and the
FireWire 800 driver. Before using this utility, unplug all
devices from the FireWire 800 ExpressCard.
1. Click Start, Programs, Unibrain ubcore, Tools then
ubSwitch.
2. Right click the ubSwitch icon located in the system
tray by the clock.
3. Click the 1394 Adapter that you want to switch, then
click on Microsoft 1394 Drivers.
Note: If your system has multiple 1394 adapters
installed, make sure that you click on the 1394
adapter that the camcorder will be plugged into.
4. Windows will display an information box when the
driver is ready for use. It may take a few seconds for
this box to appear.
Note: To switch back to the FireWire 800 driver,
follow the same procedures, but in step 3 instead of
clickingonMicrosoft1394Drivers, clickonUnibrain
1394 Drivers.

9
Blank Page

10
Blank Page