SIIG SATA II PCIe RAID User manual

1
04-0389C
Introducing the SATA II PCIe RAID
The SATA II PCIe RAID is an ultra high-speed two
channelSerialATAGenerationIIRAIDcontrollerforuse
in PCI Express enabled systems.
FeaturesandBenefits
• CompliantwithPCIExpressBaseSpecification1.0A
• Compliant with Serial ATA 1.0 specifications with
support for full complement of SATA II optional
features
• PCIExpress1-lane(x1)SATAIIadapterworkswith
PCI Express slots with different lane width
• Installs in any available PCI Express slot and
supportsdatatransferratesupto3.0Gbps(300MBps)
• Supports Native Command Queuing (NCQ),
Non-zero offsets NCQ, and Out-of-order data
delivery NCQ
• Independent command fetch, scatter/gather, and
command execution
• Supports RAID 0 (striping) and RAID 1 (mirroring)
for speed and data protection respectively
SystemRequirements
• PCIExpress-enabledsystemwithoneavailablePCI
Express slot
• Windows®7 (32-/64-bit) / Vista (32-/64-bit) /
XP (32-/64-bit) / Server 2003 & 2008 (32-/64-bit) /
2000
SATA II PCIe RAID
QuickInstallationGuide

2
PackageContents
•SATA II PCIe RAID
• Spare enhanced low profile bracket
• 2 Serial ATA data cables
• Dual-connector Serial ATA power cable
• Driver software CD
• Quick Installation Guide
Layout
Figure 1. SATA II PCIe RAID layout
* Note: Connect the hard disk drive activity LED
of the system case to the pins horizontally. This
connection is optional.
CH1
CH2
Hard Disk
LED Pins
(optional)*
HDD Activity
LED
Serial ATA
Connectors

3
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the back of the
computer.
3. Remove your computer cover.
4. RemovetheslotbracketcoverfromanavailablePCI
Express slot.
5. To install the card, carefully align the card's bus
connector with the selected PCI Express slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.
6. Replace the slot bracket holding screw to secure the
card.
7. Now go to Device Connection to connect your
Serial ATA hard disk drives.
DeviceConnection
The SATA II PCIe RAID is a two channel Serial ATA
controllerthatsupportstwoSerialATAharddiskdrives.
It is recommended to use identical hard drives for all
RAID configurations, however, it's possible to combine
hard drives of different sizes and makes.

4
1. Install your hard disk drive(s) in the chassis.
2. ConnecttheSerialATAharddiskdrivetothesystem
power supply using the included Dual Connector
Serial ATA power cable.
Note: For hard drives with both SATA power
connectorandlegacy5-pinconnector,useeitherthe
SATA power connector or the legacy 5-pin power
connector. Using both power connectors may
damage the hard drive.
3. Connect one end of the Serial ATA cable to the hard
disk drive.
Figure 2. Hard disk drive connections
4. AttachtheotherendoftheSerialATAdatacabletothe
Serial ATA connector on the SATA II PCIe RAID.
Figure 3. Connecting the Serial ATA data cable(s)
Serial ATA cable
Power cable
Serial ATA cable

5
5. Follow the same instructions to connect the second
hard drive. Device connection is now complete.
Note: If it is your desire to monitor disk activity of
the Serial ATA hard drives, you may at this time
connect the hard disk LED of the system case to the
Hard Disk LED Pins on the Serial ATA controller.
Figure 4. Connecting HDD LED
6. Replace the computer cover and reconnect the
power cord. Go to RAID Arrays to configure the
RAIDBIOS.
RAID Arrays
RAID Arrays are setup in the SATA II PCIe RAID BIOS.
Find your RAID set from the table of contents.
Table of Contents
RAID 0 (striping)............................................page 6-7
RAID 1 (mirroring).........................................page 7-8
Rebuilding a Failed Mirror Set....................page 8-9
Deleting RAID Arrays ...................................... page 9
Resolving Conflicts......................................... page 10
Low Level Format........................................... page 10
Logical Drive Info ........................................... page 10

6
RAID 0 (Striping)
This RAID array to be used on New/Blank hard drives.
Striping will destroy existing data on the hard drive.
Auto Configuration is recommended. For applications
that require custom chunk size, Manual Configuration
is offered.
Auto Configuration (recommended)
The default chunk size is 64k when selecting Auto
configuration.
1. AstheBIOSbootspressCtrl+SorF4whenprompted
to enter the RAID BIOS.
2. At the next screen select Create RAID Set, then
press Enter.
3. Select RAID0, then press Enter.
4. Select Auto configuration, then press Enter.
5. Input the RAID size, press Enter.
6. WhenaskedAreYouSure(Y/N)?,pressYtoaccept.
7. Press Ctrl+E to exit the BIOS.
8. When asked Are you sure to exit (Y/N)?, press Yto
exit and reboot.
9. Continue with Fdisk and Format steps as if you
were installing a conventional hard drive.
Manual Configuration
1. AstheBIOSbootspressCtrl+SorF4whenprompted
to enter the RAID BIOS.
2. At the next screen select Create RAID Set, then
press Enter.
3. Select RAID0, then press Enter.
4. Select Manual configuration then press Enter.

7
5. Select chunk size from 8k, 16k, 32k, 64k or 128k,
then press Enter.
6. Select the first drive, press Enter.
7. Select the second drive, press Enter.
8. Input the RAID size, press Enter.
9. WhenaskedAreYouSure(Y/N)?,pressYtoaccept.
10. Press Ctrl+E to exit the BIOS.
11. When asked Are you sure to exit (Y/N)?, press Yto
exit and reboot.
12. Continue with Fdisk and Format steps as if you
were installing a conventional hard drive.
RAID 1 (Mirror)
For New/Blank Hard Drives
1. AstheBIOSbootspressCtrl+SorF4whenprompted
to enter the RAID BIOS.
2. At the next screen select Create RAID Set, then
press Enter.
3. At the next screen select RAID1 then press Enter.
4. Select Auto configuration, then press Enter.
5. Input the RAID size, press Enter.
6. WhenaskedAreYouSure(Y/N)?,pressYtoaccept.
7. Press Ctrl+E to exit the BIOS.
8. When asked Are you sure to exit (Y/N)?, press Yto
exit and reboot.
9. Continue with Fdisk and Format steps as if you
were installing a conventional hard drive.
For Existing Hard Drives with Data
1. AstheBIOSbootspressCtrl+SorF4whenprompted
to enter the RAID BIOS.

8
2. At the next screen select Create RAID Set, then
press Enter.
3. At the next screen select RAID1 then press Enter.
4. Select Manual configuration, then press Enter.
5. Select the Source drive, press Enter.
6. Select the Target drive, press Enter.
7. Select Create with data copy, then press Enter.
8. Select online copy, then press Enter.
Note: Selecting Online Copy builds the mirror
while in Windows. Selecting Offline Copy builds
the mirror before exiting the RAID BIOS.
9. Input the RAID size, press Enter.
10. Press Ctrl+E to exit the BIOS.
11. When asked Are you sure to exit (Y/N)?, press Yto
exit and reboot.
RebuildingaFailedMirrorSet
Whenafailuretoonememberoccurs,youwillbenotified
either by the RAID BIOS during boot or by the SATA
Raid5 GUI while in Windows. The steps below will
guide you in rebuilding a failed mirror set.
For Offline Mirror Rebuild (SATA RAID BIOS)
1. Replacethe failed drivewith one ofequal or greater
capacity, then power on the computer.
2. During boot press Ctrl+S or F4 to enter the RAID
BIOS.
3. Select Create RAID Set press Enter.
4. Select SPARE DRIVE, then press Enter.
5. Select the single hard drive then press Enter.

9
6. Input the RAID size, press Enter. When asked Are
You Sure (Y/N)?, press Yto confirm.
7. Select Rebuild Raid 1 Set, press Enter.
8. When asked Are you sure (Y/N)?, press Yconfirm.
The mirror will begin rebuilding. Do not interfere
with the process.
9. When rebuilding is finished, press Ctrl+E.
10. When asked Are you sure to exit (Y/N)?, press Yto
exit and reboot.
For Online Mirror Rebuild (in Windows)
1. Replacethefaileddrivewithoneofequalorgreater
capacity, then power on the computer.
2. When Windows resumes, at the SATA SoftRaid 5
screen,clickLegacySupport,RebuildLegacyRAID
Group.
Note: If Legacy Support does not show, click File,
Configuration, AdvancedOptions. Check Legacy
(Bootable) Support, then click OK.
3. At Rebuild Legacy RAID Group box, hold down
the Ctrl key, select both hard drives, click Rebuild.
4. Click OK, then click Cancel to close the window.
5. Rebuild time may take several hours or more,
depending on the size of the mirror set.
DeletingRAIDArrays
1. AstheBIOSbootspressCtrl+SorF4whenprompted
to enter the RAID BIOS.
2. Select Delete RAID Set, then press Enter.
3. Select the RAID set then press Enter.
4. WhenaskedAreYouSure(Y/N)?,pressYtoconfirm.

10
ResolvingConflicts
When a RAID set is created, the metadata written to the
disk includes drive connection information. If, after a
diskfailure, the replacement diskwas previouslypartof
a RAID set (or used in another system), it may have
conflictingmetadata. Ifso,thiswillprohibittheRAIDset
frombeingeithercreatedorrebuilt,inorderfortheRAID
set to function properly, this old metadata must be first
overwrittenwiththenewmetadata.Toresolvethis,from
the main BIOS window select Resolve Conflicts, then
press Enter, the correct metadata, including the correct
drive connection information, will be written to the
replacement disk.
LowLevelFormat
Low Level Format is built into the RAID BIOS to make it
more convenient to erase the entire contents of a hard
disk drive, including data, drive and partition
information. The Low Level Format utility works on
singleharddrivesonly,beforetheRAIDsetisconfigured.
LogicalDriveInfo
This menu item allows the display of the assignment of
physical drives within a logical set (RAID0, RAID1, etc.).
This is a display only function.

11
Software Installation
This section provides information on how to install the
SATA II PCIe RAID drivers.
Windows7
For A New Installation
1. SetuptheRAIDarraypriortoWindowsinstallation.
2. Follow Windows installation procedure.
3. At Where do you want to install Windows?, click
Load Driver.
4. Insert the driver CD, click Browse.
5. Double click your CD-ROM drive,
For 32-bit Windows 7: select 32bit, then click OK.
For 64-bit Windows 7: select 64bit, then click OK.
6. Select Silicon Image SiI 3132 SoftRaid5
Controller..., then click Next.
7. Follow the on-screen instructions to complete
Windows 7 operating system installation.
WhenWindowsinstallationcompletes,gotoSATARaid5
GUI on page 19 and install the RAID utility.
For An Existing Installation
1. SetuptheRAIDarraypriortodriverinstallationand
boot up to Windows.
2. Right click Computer, click Manage, select Device
Manager.
3. Double click RAID Controller, then click Update
driver.
4. Insert driver CD, click Browse my computer for
driversoftware.

12
5. For 32-bit system: Type D:\32bit, then click Next.
(Change D: to match your CD-ROM drive letter)
For 64-bit system: Type D:\64bit, then click Next.
(Change D: to match your CD-ROM drive letter)
6. Click Close to complete the installation.
When Windows resumes, go to SATARaid5 GUI on
page 19 and install the RAID utility.
ToVerifyWindows7Installation
1. Right click Computer, click Manage, select Device
Manager.
2. Double click Storage controllers, then double click
Silicon Image Sil 3132 SoftRaid 5 Controller to
display driver properties. A message This device is
working properly is displayed in the dialog box, the
driver has been correctly installed.
WindowsServer2008
For A New Installation
1. SetuptheRAIDarraypriortoWindowsinstallation.
2. Follow Windows installation procedure.
3. At Where do you want to install Windows?, click
Load Driver.
4. Insert the driver CD, click Browse.
5. Double click your CD-ROM drive,
For 32-bit Server 2008 select 32bit, then click OK.
For 64-bit Server 2008: select 64bit, then click OK.
6. Select Silicon Image SiI 3132 SoftRaid5
Controller..., then click Next.
7. Follow the on-screen instructions to complete
WindowsServer2008operatingsysteminstallation.

13
WhenWindowsinstallationcompletes,gotoSATARaid5
GUI on page 19 and install the RAID utility.
For An Existing Installation
1. SetuptheRAIDarraypriortodriverinstallationand
boot up to Windows.
2. Atthe Found NewHardwarewindow, clickLocate
andinstallthedriverautomatically(recommended).
3. Click Don't search online. Insert the driver CD.
4. Click Close to complete the installation.
When Windows resumes, go to SATARaid5 GUI on
page 19 and install the RAID utility.
ToVerifyWindowsServer2008Installation
1. Right click Computer, click Manage, select Device
Manager.
2. Double click Storage controllers, then double click
Silicon Image Sil 3132 SoftRaid 5 Controller to
display driver properties. A message This device is
working properly is displayed in the dialog box, the
driver has been correctly installed.
WindowsVista™
For A New Installation
1. SetuptheRAIDarraypriortoWindowsinstallation.
2. Follow Windows installation procedure.
3. At Where do you want to install Windows?, click
Load Driver.
4. Insert the driver CD, click Browse.
5. Double click your CD-ROM drive,
For32-bitWindowsVista: select32bit,thenclickOK.
For64-bitWindowsVista: select64bit,thenclickOK.

14
6. Select Silicon Image SiI 3132 SoftRaid5
Controller..., then click Next.
7. Follow the on-screen instructions to complete
Windows Vista operating system installation.
WhenWindowsinstallationcompletes,gotoSATARaid5
GUI on page 19 and install the RAID utility.
For An Existing Installation
1. SetuptheRAIDarraypriortodriverinstallationand
boot up to Windows.
2. Atthe Found NewHardwarewindow, clickLocate
andinstallthedriverautomatically(recommended).
3. Insert the driver CD, click Continue.
4. Click Next, then Close to complete the installation.
When Windows resumes, go to SATARaid5 GUI on
page 19 and install the RAID utility.
ToVerifyWindowsVistaInstallation
1. RightclickComputer,clickManage,clickContinue,
select Device Manager.
2. Double click Storage controllers, then double click
Silicon Image Sil 3132 SoftRaid 5 Controller to
display driver properties. A message This device is
working properly is displayed in the dialog box, the
driver has been correctly installed.
Windows XP / Server 2003 (32-bit )
For A New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents
of the 32bit folder, found on the driver CD, onto a blank
floppy disk then follow the directions in the next page.

15
1. SetuptheRAIDarraypriortoWindowsinstallation.
2. Follow Windows installation procedure.
3. AttheWindowsSetupscreen,pressF6toinstallthe
RAID driver.
4. When prompted, press Sto specify the location of
the driver.
5. Insert the floppy disk, then press Enter.
6. SelectSiliconImageSiI3132SoftRaid5Controller
for Windows XP/Server 2003, then press Enter.
7. Press Enter again to finish the driver installation,
then follow the on-screen instructions to complete
your Windows installation.
WhenWindowsinstallationcompletes,goto SATARaid5
GUI on page 19 and install the RAID utility.
For An Existing Installation
1. SetuptheRAIDarraypriortodriverinstallationand
boot up to Windows.
2. At the Found New Hardware Wizard:
XP (w/SP1 or earlier) / Server 2003: continue to step
#3.
XP (w/SP2 or later) / Server 2003 (w/ SP1 or later):
select No, not at this time, then click Next.
3. Insert the driver CD, select Install the software
automatically (Recommended),and click Next.
4. Click Finish to complete the driver installation.
When Windows resumes, go to SATARaid5 GUI on
page 19 and install the RAID utility.

16
Windows XP / Server 2003 (64-bit )
For A New Installation
A new installation requires a floppy disk for the driver
installation. Tomake thisfloppy disk,copy thecontents
of the 64bit folder, found on the driver CD, onto a blank
floppy disk then follow the directions below.
1. SetuptheRAIDarraypriortoWindowsinstallation.
2. Follow Windows installation procedure.
3. RestartthecomputerwhenpromptedbyWindows'
installation.
4. AttheWindowsSetupscreen,pressF6toinstallthe
RAID driver.
5. When prompted, press S to specify the location of
the driver.
6. Insert the floppy disk, then press Enter.
7. SelectSiliconImageSil3132SoftRaid5Controller
(64-bit Extended), then press Enter.
8. Press Enterto finish driver installation, then follow
the on-screen instructions to complete Windows
installation.
WhenWindowsinstallationcompletes,gotoSATARaid5
GUI on page 19 and install the RAID utility.
For An Existing Installation
1. Setup the RAID array prior to driver installation
and boot up to Windows.
2. At the Found New Hardware Wizard:
XP (w/SP1 or earlier) / Server 2003: continue to step
#3
XP (w/SP2 or later) / Server 2003 (w/ SP1 or later):
select No, not at this time, then click Next.

17
3. Insert the driver CD, select Install the software
automatically (Recommended),and click Next.
4. Accept the default entry, then click Next.
5. Click Finish.
6. Repeat steps 2-5.
7. Click Yes to restart to complete the installation.
When Windows resumes, go to SATARaid5 GUI on
page 19 and install the RAID utility.
Windows2000
For A New Installation
A new installation of Windows 2000 requires a floppy
disk for the driver installation. To make this floppy disk,
copythe contentsof the32bitfolder, found on the driver
CD, onto a blank floppy disk then follow the directions
below.
1. SetuptheRAIDarraypriortoWindowsinstallation.
2. Follow Windows 2000 installation procedure.
3. At the Windows 2000 Setup screen, press F6 to
install the RAID driver.
4. When prompted, press S to specify the location of
the driver.
5. Insert the floppy disk, then press Enter.
6. SelectSiliconImageSil3132SoftRaid5Controller
for Windows 2000, then press Enter.
7. Press Enter again to finish driver installation, then
follow the on-screen instructions to complete the
Windows installation.
WhenWindowsinstallationcompletes,goto SATARaid5
GUI on page 19 and install the RAID utility.

18
For An Existing Installation
1. SetuptheRAIDarraypriortodriverinstallationand
boot up to Windows.
2. At Found New Hardware Wizard, click Next.
3. Select Search for a suitable driver for my device
(recommended), then click Next.
4. InsertthedriverCD,checkCD-ROMdrives,uncheck
the other boxes, click Next, click Next again, then
click Finish.
5. Repeat steps 2-4.
6. Restart Windows to complete the installation.
When Windows resumes, go to SATARaid5 GUI on
page 19 and install the RAID utility.
ToVerifyWindows2000 / XP / 2003 Installation
1. Right click My Computer, click Manage.
2. Select Device Manager.
3. Double click SCSI and RAID controllers, then
double click Silicon Image Sil 3132 SoftRaid 5
Controller to display driver properties. A message
This device is working properly is displayed in the
dialog box, the driver has been correctly installed.

19
SATARaid5 GUI
The SATARaid5 GUI provides the user an easy way to
monitor your RAID set.
SATARaid5GUIInstallation
Note:Windows2000SP4orlaterisrequiredforinstallation.
1. Insert the driver installation CD.
2. At the Windows desktop click Start, then Run.
For Windows 7/ Vista / Server 2008: In the Start
Search box, type D:\gui\setup.msi, press Enter.
(Change D: to match your CD-ROM drive letter)
ForXP/Server2003: TypeD:\gui\setup.msi,then
clickOK.(ChangeD:tomatchyourCD-ROMdrive
letter)
For Windows 2000: Type D:\gui\setup2000.msi,
then click OK. (Change D: to match your CD-ROM
drive letter)
3. Follow the on-screen instructions to complete the
installation.
SATARaid5GUIOverview
TheinstallationprogramconfigurestheSATARaid5GUI
to automatically start when Windows is started. If the
GUI does not automatically start or is closed by the user,
choose the SATARaid5 program from the start menu to
launch the program. Upon launching the GUI, the main
window should appear similar to the following.

20
RAID Groups window
This window identifies SATA host adapters and
configured RAID groups. Selecting each RAID group in
the RAID Groups window, members consisting of the
RAID group will be highlighted in the Device
Configuration window.
RightclickingoneachnodeintheRAIDGroupswindow,
a popup menu will be displayed to let the user select an
actiontobeperformedfortheselectedcontrollerorRAID
group.
Device Configuration window
This window identifies all physical drives and their
partitions. A physical drive can be partitioned into
several portions and each portion can be a RAID group
member.
RAID Groups
window Device Configuration
window