SIIG CE-H23411-S1 Product information sheet

1
4K HDR HDMI 2.0 & USB 2.0
Extender Over HDBaseT
with RS-232 & IR
User Reference Guide
04-1123A
P/N: CE-H23411-S1

2
Introduction
The 4K HDR HDMI 2.0 & USB 2.0 Extender Over HDBaseT
with RS-232 & IR extends HDMI transmission distance
up to 330ft (100m) at 1080p or 230ft (70m) at 4K over
an economical CAT5e/6 cable. Plus, bi-directional
extension of IR, RS232 and USB 2.0 for advanced and
interactive applications.
FeaturesandBenefits
Supports video resolutions up to 4Kx2K @60Hz
(4:4:4 8bit) or HDR 4Kx2K @60Hz (4:2:0 10bit) to
deliver crystal clear images
7.1 Digital sound capabilities as well as
uncompressed LPCM and compressed DTS-HD
& Dolby True HD for a state-of-the-art
entertainment experience
PoC (Power over Cable) feature, only one power
adapter is required to power both the transmitter
and receiver units
Bi-directional IR sensors allow you to remotely
control the HDMI source device from the remote
display side or control the remote display from
the source device side
Supports 3D, CEC, HDMI 2.0 and HDCP 2.2
protocols. Bandwidth up to 18Gb/s
ARC feature allows you to free the audio from on-
demand content within a Smart TV with ARC
Premium metal housing with ventilation panels
improve heat dissipation for enhanced safety
and stability
Built-in phoenix connector for RS232 control
signal transmission or firmware update. Included
mounting ears for easy installation

3
Specifications
PackageContents
4K HDR HDMI 2.0 & USB 2.0 Extender (TX & RX)
Power adapter
IR blaster extension cable & IR receiver extension
cable
Mounting ears & Screw kit
Terminal block
User Reference Guide
Compliance HDMI 2.0a / HDCP 2.2
Resolution HDR 4Kx2K @60Hz (4:2:0 10bit) / 4Kx2K@60Hz (4:4:4 8bit)
Audio LPCM, DTS-HD and Dolby True HD (7.1CH)
Transmission Distance HDR 4Kx2K @60Hz: Up to 70m
1080p @60Hz: Up to 100m
IR Signal Frequency 20KHz to 60KHz
Connectors
TX:
1x 19-pin HDMI Type-A, Female
1x 3.5mm audio jack (Stereo)
1x 3.5mm IR Blaster
1x 3.5mm IR Receiver
1x 9-pin USB Type-A, Female (Device)
1x Micro USB, Female (Host)
1x Dip switch
1x 3-pin phoenix connector (RS-232)
3x LED indicator (Power/Link/Signal)
1x 8-pin RJ45
1x Power jack
RX:
1x 19-pin HDMI Type-A, Female
1x 3.5mm audio jack (Stereo)
1x S/PDIF output
1x 3.5mm IR Blaster
1x 3.5mm IR Receiver
1x 9-pin USB Type-A, Female (Device)
1x Micro USB, Female (Host)
1x Dip switch
1x 3-pin phoenix connector (RS-232)
3x LED indicator (Power/Link/Signal)
1x 8-pin RJ45
1x Power jack
Housing Material Metal
Power Adapter Input: AC 100-240V/ 50~60Hz
Output: DC 24V / 1A

4
IR Out
Note: With PoC technology, only one power
adapter is needed to power both the
Transmitter and Receiver.
Figure 1: Transmitter (TX) - front
Layout
HDMI In Stereo Input
IR In
HDMI In: Connect your HDMI source here with
an HDMI cable (cable not included)
Stereo Input: Provides a channel to extend an
external analog audio to receiver over HDBaseT
IR Out: Infrared 3.5mm socket. Plug IR Blaster
extension cable here. See instructions on page 8.
IR In: Infrared 3.5mm socket. Plug IR Receiver
extension cable here. See instructions on page 8.
USB Type-A
Micro USB
RS-232 RJ45
Dip Switch
Power Jack
Figure 2: Transmitter (TX) - rear

5
Figure 3: Receiver (RX) - front
USB Type-A: Connect to USB Device
Micro USB: Connect to USB Host
Phoenix connector (RS232): Connect to the
included terminal block and RS-232 connector
(not included), then connect to a serial port device
or computer for data transferring
Dip Switch: Refer to below table for configuration
- ON: In lower position
- OFF: In upper position
RJ45 (HDBT Out): Connect the Cat5e/6 cable
Power Jack: Connect the included 24V DC power
adapter here (or the Receiver's power jack)
HDMI Out
Stereo
Output
IR In
S/PDIF
Output
IR Out
DIP Switch Position Description
Pin 1 (option 1) TX On (default) Connect Micro USB port to
USB Host
RX OFF (default) Connect USB device to
Type-A port
Pin 1 (option 2) TX OFF Connect USB device to
Type-A port
RX ON Connect Micro USB port to
USB Host
Pin 2 & 3
Pin 2 (TX & RX) Pin 3 (TX & RX)
ON ON HDBaseT firmware update
ON OFF HDBaseT monitor mode
OFF ON System firmware update
OFF (default) OFF (default) HDMI extender mode

6
HDMI Out: Connect your HDMI display with an
HDMI cable (cable not included)
Stereo Output: External analog audio output
from transmitter over HDBaseT
S/PDIF Output: Local ARC output
IR Out: Infrared 3.5mm socket. Plug IR Blaster
extension cable here. See instructions on page 8.
IR In: Infrared 3.5mm socket. Plug IR Receiver
extension cable here. See instructions on page 8.
USB Type-A
Micro USB
RS-232 RJ45
Dip Switch
Power Jack
USB Type-A: Connect to USB Device
Micro USB: Connect to USB Host
Phoenix connector (RS232): Connect to the
included terminal block and RS-232 connector
(not included), then connect to a serial port device
or computer for data transferring
Dip Switch: Refer to the table on page 5 for
details.
RJ45 (HDBT In): Connect the Cat5e/6 cable
Power Jack: Connect the included 24V DC power
adapter here (or the Transmitter's power jack)
Figure 4: Receiver (RX) - rear

7
RS-232 Wire Connection
1. Insert the included terminal block to Phoenix
connector.
2. Connect the wires (not included) to the included
Terminal Block and the RS232 connector as below
diagram.
- Via pin to pin (Parallel) connector or cable:
Figure 5
TX
RX
GND
3 TXD
5 GND
2 RXD
Figure 6
TX
RX
GND
3 TXD
5 GND
2 RXD
- Via null connector or cable:

8
IR Extenders (20~60kHz IR devices supported)
IR Blaster cable: Plug into the Transmitter's or
Receiver's IR Out to emit IR signals
IR Receiver cable: Plug into the Receiver's or
Transmitter's IR In to receive IR signals
Control your media player (such as DVD) at the TV
side using the media player's remote controller
Plug the IR Receiver cable to the Receiver's IR In
port
Plug the IR Blaster cable to the Transmitter's IR
Out port.
Control your TV at the media player side using the
TV's remote controller
Plug the IR Receiver cable to the Transmitter's
IR In port.
Plug the IR Blaster cable to the Receiver's IR Out
port.
Figure 7: IR Blaster cable
(Connect to IR Out)
Figure 8: IR Receiver cable
(Connect to IR In)
Important Note: Incorrect placement of IR Receiver
and IR Blaster cables may result in cable failures.
Please check carefully before plugging in the IR cables
to proper IR sockets.

9
HardwareInstallation
Note:Toachieveoptimalperformance,ashielded 100%
copper wire CAT6/7 cable is recommended.
1. Power off all devices including your HDMI source
anddisplay.
2. Connect your HDMI source to the Transmitter's
HDMI IN connector with an HDMI cable (not
included).
3. Optional: Connect the IR Receiver or Blaster
extension cable according to the instructions on
page 8.
4. Connect USB Host/Device to both TX and RX
units.
5. Connect audio source to TX and audio receiver/
speaker to RX unit.
6. Connect your HDMI display to the Receiver's
HDMI OUT connector with a HDMI cable (not
included).
7. Optional: Connect the IR Receiver or Blaster
extension cable according to the instructions on
page 8.
8. Connect and link the Transmitter and Receiver
by a CAT5e/6 cable.
9. Plug the included power adapter into the
Transmitter's or Receiver's Power Jack, then
plug the power adapter into a reliable power
outlet. (Note: It's recommended to connect it to
the Transmitter)
10. Power on your HDMI device and HDMI display.
11. The HDMI Extender is ready for use.

10
Application
Extends HDMI signals such as game consoles, DVD
players or computers up to 100m (330ft). Equipped
with bi-directional IR pass-through path, RS-232 serial
port control and USB 2.0, offers the convenient path
for interactive applications, such as touch panels.
Makes it a great solution for digital signage with long
distance A/V transmission.
Figure 9: Application
* When using the remote control, please make sure its distance to the IR
Receiver extension cable is within 5m (16.4ft) and without obstructions.
Blu-ray player
HDMI display
Control system
Stereo input