SIIG Cyber 1S1P PCI User manual

1
04-0344C
Introducing the Cyber 1S1P PCI
The Cyber 1S1P PCI high-speed serial I/O card provides
one 9-pin serial port and one parallel port.
FeaturesandBenefits
•Conforms to PCI v2.2 Plug and Play
•Full support for Windows-based software
•Reduces CPU load and improves system
performance dramatically
•IRQ sharing feature reduces IRQ conflicts
•High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, label printers and other serial port
devices
•Built-in FIFO buffers dramatically increase data
transmit/receivespeed,especiallyunderWindows'
multitasking environment
•Each serial port can be configured for either 5v or
12v output, for serial devices that require power
•IEEE 1284 compliant SPP/EPP/ECP parallel port
SystemRequirements
•Pentium or equivalent computer with an available
PCI slot
•Windows®95/98/98SE/ME/NT 4.0/2000/XP (32-
/64-bit)/Server2003(32-/64-bit)/Vista(32-/64-bit)
Cyber 1S1P PCI
Quick Installation Guide

2
PackageContents
•Cyber 1S1P PCI board
• Driver CD
• Quick Installation Guide
Layout
Figure 1. Layout
JumperSettings(JP1)
Open = 0 volts (default)
Short 1-2 = 5V
Short 2-3 = 12V
Note: Most serial devices do not require additional
power through the serial port. Refer to your serial
device's manual for more information. This jumper
can be removed if it's not used.
JP1
Serial Port
Parallel Port

3
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the back of the
computer.
3. Remove your computer’s cover.
4. Remove the slot bracket from an available PCI slot.
5. Set JP1 jumper settings to the desired voltage only
if your serial device needs additional power from
the serial port. However, most serial devices do not
require additional power. For more information,
see Figure 1 on page 2. Skip this step if power is not
required.
6. To install the card, carefully align the card's bus
connector with the selected PCI slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.
7. Replace the slot bracket holding screw to secure the
card.
8. Replacethecomputercoverandreconnect thepower
cord.

4
Driver Installation
This section provides information on how to install the
Cyber 1S1P PCI drivers.
Windows95
1. At the Update Device Driver Wizard window, click
Next.
2. Insert the driver CD, and click Other Locations.
Type in D:\9x, click OK, then Finish. (Change D: to
match your CD-ROM drive letter)
3. From the Insert Disk window, click OK. When the
Copying Files dialog box appears, type in
D:\9x, then click OK.
4. Repeat steps 1-3.
5. Restart Windows to complete the installation.
Windows98/98SE
1. At the Add New Hardware Wizard window, click
Next.
2. Select Search for the best driver for your device
(Recommended), then click Next.
3. Select Specify a location, uncheck the other boxes,
insert the driver CD, type in D:\9x, then click Next.
(Change D: to match your CD-ROM drive letter)
4. Click Next, then Finish.
5. Repeat steps 1-4.
6. Restart Windows to complete the installation.

5
WindowsME
1. At the Add New Hardware Wizard, choose Specify
the location of the driver (Advanced), then click
Next.
2. Check Specify a location, uncheck the other box,
insert the driver CD, type in D:\Me, then click Next.
(Change D: to match your CD-ROM drive letter)
3. Click Next and Finish.
4. Repeat steps 1-3.
5. Restart Windows to complete the installation.
ToVerifyWindows95/98/98SE/MEInstallation
1. From the main desktop, right click My Computer,
click Properties, then click Device Manager.
2. Double click Ports (COM & LPT), CyberSerial PCI
16Cxxx..., Printer Port..., and CyberParallel PCI
should be displayed.
3. Double click Multi-function adapters, SIIG
CyberPro 1S1P PCI board should be displayed.
WindowsNT4.0
1. From the desktop click Start, then Run.
2. Insert the driver CD, type in
D:\NT4\Install_Serial.exe, then click OK.
(Change D: to match your CD-ROM drive letter)
3. Click Next when the Welcome window appears.
4. Choose Install, then click Next.
5. Click Yes, then click Exit.
6. From the desktop click Start, then Run.

6
7. TypeinD:\NT4\Install_Parallel.exe, thenclickOK.
(Change D: to match your CD-ROM drive letter)
8. Repeat steps 3-5.
9. Click Yes to restart Windows to complete the
installation.
ToVerifyWindowsNT4.0Installation
1. Go to Start / Settings / Control Panel,double click
Ports device icon.
2. AnewCOMportwillbeassigned when successfully
installed.
3. Click Start, Programs, Administrative Tools,
Windows NT Diagnostics. Click Resources tab,
SIIGpar and SIIGser should be displayed.
Windows2000
1. At the Found New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended), and click Next.
3. Select Specify a location, uncheck the other boxes,
and click Next.
4. Insert the driver CD, type in D:\2000, then click OK.
(Change D: to match your CD-ROM drive letter)
5. Click Next and Finish.
6. Repeat steps 1-5 two more times.
7. Restart Windows to complete the installation.

7
32-bitWindowsXP/Server2003
1. At the Found New Hardware Wizard, insert the
driver CD.
For XP w/SP1 or earlier/ Server 2003: go to step #2.
For XP w/SP2 or later/Server 2003 wSP1 or later:select
No, not this time, click Next.
2. Select Install the software automatically
(Recommended,then click Next.
3. Click Finish.
4. Repeat steps 1-3 two more times.
5. Restart Windows to complete the installation.
64-bitWindowsXP/Server2003
1. At the Found New Hardware Wizard, insert the
driver CD.
For XP w/SP1 or earlier/ Server 2003: go to step #2.
For XP w/SP2 or later/Server 2003 wSP1 or later:select
No, not this time, click Next.
2. Select Install the software automatically
(Recommended,then click Next.
3. Click Continue Anyway, then click Finish.
4. Repeat steps 1-3 several more times.
5. Restart Windows to complete the installation.
ToVerifyWindows2000/XP/2003Installation
1. Right click My Computer, click Manage, then select
Device Manager.
2. Double click Ports (COM & LPT), CyberSerial PCI
16Cxxx... andCyberParallel PCI... should be
displayed.
3. Double click Multifunction adapters, SIIG
CyberPro 1S1P PCI board should be displayed.

8
WindowsVista™
1. At the Found New Hardware window, insert the
driver CD, click Locate and install driver software
(recommended), then click Continue.
2. Click Next, then click Close.
3. Repeat step #2 to complete the driver installation.
Note: Windows Vista driver installation process
may take several minutes to complete.
ToVerifyWindowsVistaInstallation
1. Right click Computer,click Manage,clickContinue,
then click Device Manager.
2. Click on the +(plus sign) in front of Ports (COM &
LPT), CyberSerialPCI16Cxxx... and CyberParallel
PCI... should be displayed.
3. Double click Multifunction adapters, SIIG
CyberPro 1S1P PCI board should be displayed.
Changing COM Port Address
Some serial devices need a specific COM port in order to
work. If your serial device works properly, do not
change this setting.
Windows95/98/98SE/ME
1. From the Device Manager window double click
Ports (COM & LPT), then double click CyberSerial
PCI... serial port.
2. Click Settings tab, at the Port Name box click the
down arrow and select a COM address that is not
currently in use.
3. Click OK, click OK again to close Device Manager
to save the changes.

9
Windows2000/XP/Server2003/Vista
1. From the Device Manager window double click
Ports (COM & LPT), then double click CyberSerial
PCI... serial port.
2. Click Settings tab and click Advanced....
3. At the COM Port number box, click the down arrow
and select a COM port that is not in use. Click OK.
4. Click OK, then close Device Manager to save the
changes.
Changing Parallel Port Address (LPT)
Some parallel devices need a specific parallel port in
order to work. If your parallel device works properly, do
not change this setting.
Windows95/98/98SE/ME
1. From the Device Manager window double click
Ports(COM &LPT),thendoubleclickCyberParallel
PCI.
2. Click Settings tab, check Enable use of I/O location
278h.
3. Click OK, click OK again to close Device Manager,
andclick Yes torestartWindowsto save thechanges.
Windows2000/XP/Server2003/Vista
1. From the Device Manager window double click
Ports(COM &LPT),thendoubleclickCyberParallel
PCI....
2. Click Port Settings tab.
3. At the LPT Port Number box, click the down arrow
and select an LPT port that is not in use.
4. Click OK, then close Device Manager to save the
changes.

10
Blank Page