SIIG Cyber 1S1P PCI User manual

1
Cyber 1S1P PCI
Quick Installation Guide
04-0344A
Introducing the Cyber 1S1P PCI
The Cyber 1S1P PCI high-speed serial I/O card provides
one 9-pin serial port and one parallel port.
FeaturesandBenefits
•Conforms to PCI v2.2 Plug and Play
•Full support for Windows-based software
•Reduces CPU load and improves system
performance dramatically
•IRQ sharing feature reduces IRQ conflicts
•High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, label printers and other serial port
devices
•Built-in FIFO buffers dramatically increase data
transmit/receivespeed,especiallyunderWindows'
multitasking environment
•Each serial port can be configured for either 5v or
12v output, for serial devices that require power
•IEEE 1284 compliant SPP/EPP/ECP parallel port
SystemRequirements
•Pentium or equivalent computer with an available
PCI slot
•Windows 95/98/98SE/ME/NT 4.0/2000/XP/
Server 2003

2
PackageContents
• (1) Cyber 1S1P PCI board
• (1) Driver CD
• (1) Quick Installation Guide
Layout
Figure 1. Layout
JumperSettings(JP1)
Open = 0 volts (default)
Short 1-2 = 5v
Short 2-3 = 12v
Note: Most serial devices do not require additional
power through the serial port. Refer to your serial
device'smanualformoreinformation. Thisjumper
can be removed if it's not used.
JP1
Serial Port
Parallel Port

3
Hardware Installation
General instructions for installing the card are provided
below, since the design of computer cases and
motherboards vary. Refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the back of the
computer.
3. Remove your computer’s cover.
4. Remove the slot bracket from an available PCI slot.
5. Change JP1 jumper settings to the desired voltage
only if your serial device needs additional power
from the serial port. However, most serial devices
do not require additional power. For more
information, see Figure 1 on page 2. Skip this step
if power is not required.
6. To install the card, carefully align the card's bus
connector with the selected PCI slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.
7. Replace the slot bracket's holding screw to secure
the card.
8. Replacethecomputercoverandreconnectthepower
cord.

4
Software Installation
This section provides information on how to install the
Cyber 1S1P PCI drivers.
Windows95DriverInstallation
1. AttheUpdateDeviceDriverWizardwindow,click
Next.
2. Insert the driver CD, and click Other Locations.
TypeinD:\9x,clickOK,thenFinish.(ChangeD:to
match your CD-ROM drive letter)
3. From the Insert Disk window, click OK. When the
Copying Files dialog box appears, type in
D:\9x, then click OK.
4. Repeat steps 1-3.
5. Restart Windows to complete the installation.
Windows98/98SEDriverInstallation
1. At the Add New Hardware Wizard window, click
Next.
2. Select Search for the best driver for your device
(Recommended), then click Next.
3. Select Specify a location, uncheck the other boxes,
insert the driver CD, type in D:\9x,then click Next.
(Change D: to match your CD-ROM drive letter)
4. Click Next, then Finish.
5. Repeat steps 1-4.
6. Restart Windows to complete the installation.

5
WindowsMEDriverInstallation
1. AttheAddNewHardwareWizard,chooseSpecify
the location of the driver (Advanced), then click
Next.
2. Check Specify a location, uncheck the other box,
insert the driver CD, type in D:\Me, then click
Next. (Change D: to match your CD-ROM drive
letter)
3. Click Next and Finish.
4. Repeat steps 1-3.
5. Restart Windows to complete the installation.
To Verify Successful Installation In Windows 95/98/
98SE/ME:
1. From the main desktop, right click My Computer,
click Properties, then click Device Manager.
2. DoubleclickPorts(COM&LPT),CyberSerialPCI
16Cxxx..., Printer Port..., and CyberParallel PCI
should be displayed.
3. Double click Multi-function adapters, SIIG
CyberPro 1S1P PCI board should be displayed.
WindowsNT4.0DriverInstallation
1. From the desktop click Start, then Run.
2. Insert the driver CD, type in
D:\NT4\Install_Serial.exe,thenclickOK. (Change
D: to match your CD-ROM drive letter)
3. Click Next when the Welcome window appears.
4. Choose Install, then click Next.
5. Click Yes, then click Exit.
6. From the desktop click Start, then Run.

6
7. TypeinD:\NT4\Install_Parallel.exe,thenclickOK.
(Change D: to match your CD-ROM drive letter)
8. Repeat steps 3-5.
9. Click Yes to restart Windows to complete the
installation.
To Verify Successful Installation In Windows NT 4.0:
1. Go to Start / Settings / Control Panel,double click
Ports device icon.
2. AnewCOMportwillbeassignedwhensuccessfully
installed.
3. Click Start, Programs, Administrative Tools,
Windows NT Diagnostics. Click Resources tab,
SIIGpar and SIIGser should be displayed.
Windows2000DriverInstallation
1. At the Found New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended), and click Next.
3. Select Specify a location, uncheck the other boxes,
and click Next.
4. InsertthedriverCD,typeinD:\2000,thenclickOK.
(Change D: to match your CD-ROM drive letter)
5. Click Next and Finish.
6. Repeat steps 1-5 two more times.
7. Restart Windows to complete the installation.
WindowsXPDriverInstallation
1. AttheFoundNewHardwareWizard,chooseInstall
from a list or specific location (Advanced),then
click Next.

7
2. Insert the driver CD, check Include this location in
the search,uncheck the other check box, type in
D:\XP,and click Next. (Change D: to match your
CD-ROM drive letter)
3. At the Hardware Installation window, click
Continue Anyway, then Finish. Our driver has been
testedforstabilityandcompatibility.
4. Repeat steps 1-3 two more times.
5. Restart Windows to complete the installation.
WindowsServer2003DriverInstallation
1. AttheFoundNewHardwareWizard,chooseInstall
from a list or specific location (Advanced),then
click Next.
2. Insert the driver CD, check Include this location in
the search,uncheck the other check box, type in
D:\2003,and click Next. (Change D:to match your
CD-ROM drive letter)
3. At the Hardware Installation window, click
Continue Anyway, then Finish. Our driver has been
testedforstabilityandcompatibility.
4. Repeat steps 1-3 two more times.
5. Restart Windows to complete the installation.
ToVerifySuccessfulInstallationInWindows2000/XP/
Server 2003:
1. RightclickMyComputer,clickManage,thenselect
Device Manager.
2. Double click Ports (COM & LPT), CyberSerialPCI
16Cxxx... andCyberParallel PCI... should be
displayed.
3. Double click Multifunction adapters, SIIG
CyberPro 1S1P PCI board should be displayed.

8
Changing COM Port Address
Some serial devices need a specific COM port in order to
work. If your serial device works properly, do not
change this setting.
Windows95/98/98SE/ME
1. From the Device Manager window double click
Ports(COM&LPT),thendouble clickCyberSerial
PCI... serial port.
2. Click Settings tab, at the Port Name box click the
down arrow and select a COM address that is not
currently in use.
3. Click OK, click OK again to close Device Manager
to save the changes.
Windows2000/XP/Server2003
1. From the Device Manager window double click
Ports(COM&LPT),thendouble clickCyberSerial
PCI... serial port.
2. Click Settings tab and click Advanced....
3. AttheCOMPortnumberbox,clickthedownarrow
and select a COM port that is not in use. Click OK.
4. Click OK, then close Device Manager to save the
changes.

9
Changing Parallel Port Address (LPT)
Some parallel devices need a specific parallel port in
ordertowork. Ifyourparalleldeviceworksproperly,do
not change this setting.
Windows95/98/98SE/ME
1. From the Device Manager window double click
Ports(COM&LPT),thendoubleclickCyberParallel
PCI.
2. ClickSettingstab,checkEnableuseofI/Olocation
278h.
3. Click OK, click OK again to close Device Manager,
andclickYestorestartWindowstosavethechanges.
Windows2000/XP/Server2003
1. From the Device Manager window double click
Ports(COM&LPT),thendoubleclickCyberParallel
PCI....
2. Click Port Settings tab.
3. Atthe LPTPortNumberbox,clickthedownarrow
and select an LPT port that is not in use.
4. Click OK, then close Device Manager to save the
changes.

10
Blank Page

11
Technical Support
QUESTIONS? SIIG’s Online Support has the answers!
Simply visit our Web site at www.siig.com and click on
Support. Our online support database is updated daily
with new drivers and solutions. The answers to your
problems could be just a few clicks away.
If you can't find answers or solutions to your questions, you
have an option to submit the problems online to one of our
technical support analysts and we will promptly respond
to you with answers or solutions.
The 5-year manufacturer warranty supplied with this
product is offered by SIIG, Inc. If you should happen to
encounter any problems with this product, please follow
the procedures below.
1. If it is within the store's return policy period, please
return the product to the store where you purchased
from.
2. If your purchase has passed the store's return policy
period, please contact SIIG. See SIIG's Limited 5-year
Warranty card for more information.
Online Store
SIIGoffersallofourproductsonlineatourcompany
store. Visit us at http://onlinestore.siig.com to find
ourcompletelineofproducts,includinghardtofind
items and accessories (power adapters, cables,
upgrade kits, etc.).

Cyber1S1PPCIisatrademarkofSIIG,Inc.
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are
registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel
Corporation. Other names used in publication are for identification only and may be trademarks
oftheirrespectivecompanies.
July, 2004 Copyright ©2004 by SIIG, Inc. All rights reserved.
PRODUCT NAME
Cyber 1S1P PCI
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undes-
ired operation.
THE PARTY RESPONSIBLE FOR
PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Ave.
Fremont, CA 94538-3152
AboutSIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading computer upgrade
manufacturer of I/O connectivity products, including PCI & ISA
serialand parallel ports,USB, Serial ATA&UltraATA controllers,
FireWire(1394a/b),Networking,SoundCards,andotheraccessories.
SIIGisthepremierone-stopsourceofupgrades.
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly
features, and all products are backed by a 5-year manufacturer
warranty. High-qualitycontrolstandardsareevidentbytheoverall
easeofinstallationandcompatibilityofourproducts,aswellasone
ofthelowestdefectivereturnratesintheindustry. SIIGproductscan
be found in most computer retail stores, mail order catalogs, and
e-commerce sites in the Americas and the UK, as well as through
majordistributors,systemintegrators,andVARs.