SIIG CyberPro PCI 2S User manual

1
CyberPro PCI 2S
Quick Installation Guide
04-0341D
Introducing the CyberPro PCI 2S
The CyberProPCI2Shigh-speedserialI/Ocard provides
two additional 9-pin serial ports.
FeaturesandBenefits
•Conforms to PCI v2.2 Plug and Play
•Full support for Windows-based software
•Reduces CPU load and improves system
performance dramatically
•IRQ sharing feature reduces IRQ conflicts
•High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, label printers and other serial port
devices
•Built-in FIFO buffers dramatically increase data
transmit/receivespeed,especiallyunderWindows'
multitasking environment
•Each serial port can be configured for either 5V or
12V output, for serial devices that require power
SystemRequirements
•Pentium®or equivalent computer with an available
PCI slot
•Windows®7 (32-/64-bit) / Vista (32-/64-bit) / XP
(32-/64-bit)/Server2003&2008(32-/64-bit)/2000
/ NT 4.0 / ME / 98SE / 98 / 95

2
PackageContents
•CyberPro PCI 2S board
• DriverCD
• Quick installation guide
Layout
Figure 1. Layout
JumperSettings(JP1,JP2)
Open = 0 volts (default)
Short 1-2 = 5V
Short 2-3 = 12V
Note: Mostserialdevicesdonotrequireadditional
power through the serial port. Refer to your serial
device's manual for more information.
Serial Port 2
JP1 (Serial port 1)
JP2 (Serial port 2)
Serial Port 1

3
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the back of the
computer.
3. Remove your computer’s cover.
4. Remove the slot bracket from an available PCI slot.
5. SetJP1andJP2jumpersettingstothedesiredvoltage
only if your serial device needs additional power
from the serial port. However, most serial devices
do not require additional power. For more
information see Figure1 on page 2. Skip this step if
power is not required.
6. To install the card, carefully align the card's bus
connector with the selected PCI slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.
7. Replace the slot bracket holding screw to secure the
card.
8. Replacethecomputercoverandreconnectthepower
cord.

4
Driver Installation
This section provides information on how to install the
CyberPro PCI 2S drivers.
Windows7(32-/64-bit)
1. Right click Computer, click Manage, click Device
Manager.
2. Insert the driver CD. Right click PCI Serial Port,
click Update Driver Software.
3. Click Browse my computer for driver software.
4. Type D:, then clickNext. (ChangeD: to match your
CD/DVD-ROM drive letter)
5. At Windows has successfully updated your driver
software, click Close.
6 Right click Other PCI Bridge Device, click Update
DriverSoftware.
7. Repeat steps 3-5.
8. RightclickCyberSerialCommunicationPort,click
UpdateDriverSoftware.
9. Click Browse my computer for driver software.
10. TypeD:,click Next. (ChangeD:tomatchyourCD/
DVD-ROM drive letter)
11. At Windows has successfully updated your driver
software, click Close.
12. Repeat steps 8-11 to complete the installation.
WindowsVista™(32-/64-bit)
1. At the Found New Hardware window, insert the
driver CD, click Locate and install driver software
(recommended), then click Continue.
2. Click Next, then click Close.

5
3. Repeat step 2 to complete the driver installation.
Note: Windows Vista driver installation process
may take several minutes to complete.
WindowsXP(32-/64-bit)/Server2003(32-/64-bit)
1. At the Found New Hardware Wizard, insert the
driver CD.
2. Select No, not this time, click Next. (Skip this step
if not prompted)
3. Select Install the software automatically
(Recommended),then click Next.
4. Click Finish.
5. Repeat steps 1-4 two more times.
6. Restart Windows to complete the installation.
WindowsServer2008(32-/64-bit)
1. At the Found New Hardware Wizard, click Locate
and install driver software (recommended).
2. Insert the driver CD.
3. Click Don't search online.
4. ClickIdon'thavethedisc. Showmeotheroptions.
5. Click Browse my computer for driver software
(advanced).
6. TypeD:, then clickNext. (ChangeD: tomatch your
CD/DVD-ROM drive letter)
7. AtThesofwareforthisdevicehasbeensucessfully
installed, click Close.
8. Repeat steps 3-7 to complete the installation.

6
To Verify Windows 7 / Vista / XP / Server 2003 &
2008Installation
1. Check in Device Manager to verify installation.
ForWindows7:RightclickComputer,clickManage,
then click Device Manager.
For Windows Vista: Right click Computer, click
Manage,clickContinue,thenclickDeviceManager.
ForXP/Server2003:Right clickMyComputer,click
Manage, then click Device Manager.
ForServer2008:RightclickComputer,clickManage,
double click Diagnostics, then click Device
Manager.
2. Click on the +(plus sign) in front of Ports (COM &
LPT), CyberSerial 16Cxxx... should be displayed
two times.
3. Double click Multifunction adapters, SIIG
CyberPro 2S board should be displayed.
Windows2000
1. At the Found New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended), then click Next.
3. Check Specify a location, uncheck the other boxes,
then click Next.
4. InsertthedriverCD,typeinD:\2000,thenclickOK.
(Change D: to match your CD-ROM drive letter)
5. Click Next and Finish.
6. Repeat steps 1-5 two more times.
7. Restart Windows to complete the installation.

7
ToVerifyWindows2000Installation
1. Right click My Computer, click Manage, then click
Device Manager.
2. Click on the +(plus sign) in front of Ports (COM &
LPT), CyberSerial 16Cxxx... should be displayed
two times.
3. Double click Multifunction adapters, SIIG
CyberPro 2S board should be displayed.
WindowsME
1. At the Add New Hardware Wizard, select Specify
the location of the driver (Advanced),then click
Next.
2. Insert the driver CD, check Specify a location,
uncheck the other box, type in D:\ME,then click
Next.(Change D: to match your CD/DVD-ROM
drive letter)
3. Click Next, then Finish.
4. Repeat steps 1and 2.
5. Click Next, Next, then Finish.
6. Restart Windows to complete the installation.
Windows98/98SE
1. At the Add New Hardware Wizard, click Next.
2. Select Search for the best driver for your device
(Recommend), then click Next.
3. Insert the driver CD, check Specify a location,
uncheck the other boxes, type in D:\9x, then click
Next. (Change D: to match your CD/DVD-ROM
drive letter)
4. Click Next, then Finish.

8
5. Repeat steps 1-4.
6. Restart Windows to complete the installation.
Windows95
1. At the Update Device Driver Wizard, click Next.
2. Insert the driver CD, click Other Locations.
3. Typein D:\9x,clickOK,thenclickFinish. (Change
D: to match your CD/DVD-ROM drive letter)
4. From the Insert Disk window, click OK. When the
Copying Files dialog box pops up, type in D:\9x,
thenclickOK.(ChangeD:tomatchyourCD/DVD-
ROM drive letter)
5. Restart Windows to complete the installation.
To Verify Windows ME / 98SE / 98 / 95 Installation
1. Right click My Computer, click Properties,then
click Device Manager.
2. Double click Ports (COM & LPT), CyberSerialPCI
16Cxxx... should be displayed two times.
3. Double click Multi-function adapters, SIIG
CyberPro 2S... and PCI Function should be
displayed.
WindowsNT4.0
1. From the desktop click Start, then Run.
2. Insert the driver CD, type in
D:\NT4\Install_serial.exe, then click OK.
(Change D: to match your CD/DVD-ROM drive
letter)
3. Click Next when the Welcome window appears.
4. Select Install, then click Next.

9
5. Click Yes, then click Exit.
6. Restart Windows to complete the installation.
ToVerifyWindows NT4.0Installation
1. Click Start, Settings, Control Panel.Double click
Ports device icon.
2. Two new COM ports will be assigned when
successfully installed.

10
Changing COM Port Address
Some serial devices need a specific COM port in order to
work. If your serial device works properly, do not
change this setting.
Windows 7 / Vista / XP / Server 2003 & 2008 / 2000
1. From the Device Manager window double click
Ports (COM & LPT), then double click the
CyberSerial serial port you want to change.
2. Click Settings tab and click Advanced.
3. Click the down arrow that is next to the COM Port
numberboxandselectaCOMportthatisnotinuse.
Click OK.
4. Click OK, then close Device Manager to save the
changes.
Windows ME / 98SE / 98 / 95
1. From the Device Manager window double click
Ports (COM & LPT), then double click the
CyberSerial PCI serial port you want to change.
2. Click Settings tab, click the down arrow that is next
tothePortNameboxandselectaCOMaddressthat
is not currently in use.
3. Click OK, then close Device Manager to save the
changes.

11
Technical Support and Warranty
QUESTIONS? SIIG’sOnlineSupporthasanswers! Simplyvisitour
web site at www.siig.com and click Support. Our online support
databaseisupdateddailywithnewdriversandsolutions. Answers
toyourquestionscouldbejustafewclicksaway. Youcanalsosubmit
questions online and a technical support analysts will promptly
respond.
SIIGoffersalifetimemanufacturerwarrantywiththisproduct. Please
see our web site for more warranty details. If you encounter any
problemswiththisproduct,pleasefollowtheproceduresbelow.
A) If it is within the store's return policy period, please return the
producttothestorewhereyoupurchasedfrom.
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please
followthese steps tohave theproduct repaired or replaced.
Step1: SubmityourRMArequest.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective,anRMAnumberwillbeissued.
Step2: After obtaining an RMA number, ship theproduct.
•Properlypacktheproductforshipping. Allsoftware,cable(s)
andany otheraccessoriesthatcamewiththe originalpackage
mustbeincluded.
•Clearly write your RMA number on the top of the returned
package. SIIGwillrefusetoacceptanyshippingpackage,and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
•Youareresponsible for thecostof shipping. Shiptheproduct
to the following address:
SIIG,Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA#:
•SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
nocosttothecustomer.

CyberProPCI2SisatrademarkofSIIG,Inc. SIIGandtheSIIGlogoareregisteredtrademarksofSIIG,
Inc. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of
MicrosoftCorporationintheUnitedStatesand/orothercountries. Pentiumisaregisteredtrademark
of Intel Corporation. Other names used in this publication are for identification only and may be
trademarksoftheirrespectivecompanies.
October, 2009 Copyright © 2009 by SIIG, Inc. All rights reserved.
About SIIG, Inc.
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
of I/O connectivity products, including PCIe, PCI & ISA serial and
parallel ports, USB, Serial ATA & UltraATA controllers, FireWire
(1394a/b),networking,soundcards,andotheraccessories. SIIGisthe
premierone-stopsourceofupgrades.
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK,andthroughe-commercesites.
PRODUCT NAME
CyberPro PCI 2S
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: [phone]