SIIG DP Hi-Speed USB 4-Port PCIe User manual

1
DP Hi-Speed USB 4-Port PCIe
Quick Installation Guide
04-0486C
Introducing the Hi-Speed USB 4-Port PCIe
The DP Hi-Speed USB 4-Port PCIe adds 4 high-speed USB
2.0 ports to your system.
Features and Benefits
• Compliant with USB specifications revision 2.0
• Installs into standard height or low profile system
chassis with the included brackets
• Supports simultaneous operation of multiple
high-speed USB 2.0 and USB 1.1 devices
• Supports high-speed (480Mbps), full-speed
(12Mbps), and low-speed (1.5Mbps) data transfer
modes
• User friendly hot-swapping feature allows you to
attach/remove USB devices without turning off
your system
Note: USB 1.1 devices are limited to USB 1.1 speeds
even when they are connected to USB 2.0 host
adapters or USB 2.0 hubs.
System Requirements
• PCI Express enabled PC or Mac®computer with an
available PCIe slot
• Windows®7 (32-/64-bit) / Vista (32-/64-bit) / XP
(32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / 2000
SP4
• Mac OS®X v10.4 or later

2
PackageContents
•DP Hi-Speed USB 4-Port PCIe
• Spare low-profile bracket
• Quick installation guide
Layout
Figure 1. Board Layout
Hardware Installation
Note: For low profile systems, remove the currently
mountedbracketandinstallthesparelowprofilebracket.
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer's case for a few
seconds. Avoid any contact with internal parts and
handle card only by their external edges.
External ports
Internal port

3
1. Turn OFF the power to your computer and any
other connected peripheral device.
2. Unplug the power cord and remove the computer
cover.
3. Remove the slot bracket from an available PCIe slot.
4. Carefully align the card to the selected PCIe slot,
push the board down firmly, but gently, until it is
well seated.
5. Replace the slot bracket holding screw to secure the
card.
6. Replacethecomputercoverand reconnectthe power
cord.
Windows Driver Installation
Windows 7, Windows Vista, XP Service Pack 1 or later,
Server 2003 & 2008, and 2000 Service Pack 4 have built-in
driver support for this controller. Just install the board
and Windows will automatically detect and install the
correct drivers for it. No additional driver is necessary.
To Verify Windows Installation
1. Check Device Manage to verify installation.
For Windows 7: Right click Computer, click Manage,
then click Device Manager.
For Windows Vista: Right click Computer, click
Manage,click Continue,thenclickDevice Manager.
For Windows XP / Server 2003 / 2000: Right click My
Computer, click Manage, then click Device
Manager.
For Windows Server 2008: Right click Computer, click
Manage,doubleclickDiagnostics, thenclickDevice
Manager.

4
2. The drivers show up differently under different
versions of Windows. Please refer to the correct
Windows version to verify.
For Windows 7 / Vista: Under Universal Serial Bus
controllers, NEC to PCI Universal Host Controller
will be displayed two times and Standard
Enhanced PCI to USB Host Controller will be
displayed one time.
For Windows XP / Server 2003 & 2008 / 2000: Under
Universal Serial Bus controllers, NEC PCI to USB
Open Host Controller will be displayed two times
and NEC to PCI Enhanced Host Controller will be
displayed one time.
Mac OS Driver Installation
Mac OS X has built-in driver support for this controller.
Just install the board and Mac OS will automatically
detect and install the correct drivers for it. No additional
driver is necessary.
To Verify Mac OS X Installation
Check System Profiler to verify successfull installation.
1. Click Go, then click Utilities.
2. Double click System Profiler.
3. Under USB,USB High-Speed Bus will be displayed
one time and USB Bus will be displayed two times.

5
Blank Page

6
Blank Page

7
Technical Support and Warranty
QUESTIONS? SIIG’sOnline Support hasanswers! Simplyvisit our
web site at www.siig.com and click Support. Our online support
database is updated daily with new drivers and solutions. Answers
toyour questions could bejust a few clicksaway. You can also submit
questions online and a technical support analysts will promptly
respond.
SIIGoffers alifetime manufacturerwarrantywiththisproduct. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) Ifyourpurchase has passed thestore's return policy period,please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
•Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
•Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
•You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
•SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.

DP Hi-Speed USB 4-Port PCIe is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarksofSIIG,Inc. Microsoft,WindowsandWindowsVistaareeitherregisteredtrademarksor
trademarksofMicrosoftCorporationinthe UnitedStatesand/orother countries. MacandMacOS are
registeredtrademarksofApple Inc. Othernamesusedinthispublicationareforidentificationonlyand
maybe trademarks oftheirrespective companies.
July, 2009 Copyright © 2009 by SIIG, Inc. All rights reserved.
About SIIG, Inc.
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
of I/O connectivity products, including PCIe, PCI & ISA serial and
parallel ports, USB, Serial ATA & UltraATA controllers, FireWire
(1394a/b),networking, soundcards, andotheraccessories. SIIG isthe
premier one-stop source of upgrades.
SIIGproducts offercomprehensive usermanuals, manyuser-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK, and through e-commerce sites.
PRODUCT NAME
DP Hi-Speed USB 4-Port PCIe
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: [phone]