SIIG JU-EC2012-S1 User manual

1
Hi-Speed USB 2-Port
ExpressCard
QuickInstallationGuide
Introducing the Hi-Speed USB 2-Port
ExpressCard
The Hi-Speed USB 2-Port ExpressCard adds high-speed
USB 2.0 interface to your notebook computer.
KeyFeaturesandBenefits
• Adds two Hi-Speed USB 2.0 ports to your
ExpressCard equipped PC notebook, desktop
computer - Supports data transfer rate up to
480Mb/s
• Works with USB (2.0 & 1.1) devices including digital
cameras, scanners, CD/DVD & hard disk drives,
memory card readers, and more
• Compliant with USB specifications revision 2.0
• Supports high-speed (480Mbps), full speed
(12Mbps), and low speed (1.5Mbps) data transfer
modes
• Supports simultaneous operation of multiple high-
speed USB 2.0 and USB 1.1 devices and connects up
to 127 devices
• Can be installed in an ExpressCard /34 or /54 slot
Note: USB 1.1 devices are limited to USB 1.1 speeds
evenwhentheyareconnectedtoUSB2.0hostadapter
or USB 2.0 hubs.
04-0437B

2
SystemRequirements
• ExpressCard-enabled system with an available
ExpressCard slot
• Windows®2000 SP4/XP (32-/64-bit)/Server 2003
(32-/64-bit)/Vista (32-/64-bit)
PackageContents
• Hi-Speed USB 2-Port ExpressCard
•This quick installation guide
Layout
USB 2.0 Ports
Power Adapter Jack
Note: For devices that require more power than
provided by the USB ports, an optional power
adapter can be purchased from SIIG online store.
Most USB devices do not need this optional power
adapter to work.

3
Hardware Installation
General instructions for installing the card are provided
below. Since the design of systems may vary, refer to
your system’s reference manual for further information,
if needed.
Insert the Card into the ExpressCard slot of your system.
Makesureitisinserted allthewayinfor asolidconnection.
Driver Installation
Windows 2000 SP4, XP, Server 2003 and Vista will detect
and install the drivers automatically. No additional
driver is necessary.
ToVerifyWindowsInstallation
1. Check Device Manager to verify successful
installation.
Windows 2000/XP/Server 2003: Right click My
Computer, click Manage, then click Device
Manager.
Windows Vista™: Right click Computer, click
Manage, click Continue, then click Device
Manager.
2. Double click Universal Serial Bus controllers, and
Generic USB Hub should be displayed.
Connecting USB Devices
When connecting USB devices, hold the Hi-Speed USB
2-Port ExpressCard so it does not move from side to side,
otherwise, the ExpressCard may eject from the slot.

4
Blank Page

5
Blank Page

6
Blank Page

7
Technical Support and Warranty
QUESTIONS? SIIG’sOnline Support hasanswers! Simply visitour
web site at www.siig.com and click Support. Our online support
database is updated daily with new drivers and solutions. Answers
toyour questionscould bejust afew clicksaway. You canalso submit
questions online and a technical support analysts will promptly
respond.
SIIGoffersa lifetime manufacturerwarrantywiththis product. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) Ifyour purchasehas passedthe store'sreturn policy period, please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective, an RMA number will be issued. SIIG RMA department
can also be reached at [phone].
Step 2: After obtaining an RMA number, ship the product.
•Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
•Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
•You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
•SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.

Hi-Speed USB 2-Port ExpressCard is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarks of SIIG, Inc. Microsoft, Windows and Windows Vista are registered trademarks of
Microsoft Corporation. Other names used in this publication are for identification only and may be
trademarksoftheirrespectivecompanies.
October, 2007 Copyright © 2007 by SIIG, Inc. All rights reserved.
About SIIG, Inc.
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
of I/O connectivity products, including PCI & ISA serial and parallel
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),
networking, sound cards, and other accessories. SIIG is the premier
one-stop source of upgrades.
SIIGproductsoffer comprehensive usermanuals,many user-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK, and through e-commerce sites.
PRODUCT NAME
Hi-Speed USB 2-Port ExpressCard
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA