SIIG USB 5-Port PCI User manual

1
Hi-Speed USB 5-Port PCI
Quick Installation Guide
04-0444D
Introduction
The Hi-Speed USB 5-Port PCI adds five Hi-Speed USB ports
to your desktop computer.
Features and Benefits
• Compliant with USB specifications revision 2.0
• Conforms to PCI specifications revision 2.2
• Supports simultaneous operation of multiple
high-speed USB 2.0 and USB 1.1 devices
• Supports high-speed (480 Mbps), full-speed (12
Mbps), and low-speed (1.5 Mbps) data transfer
modes
System Requirements
PC:
• Pentium®
class computer with an available PCI slot
• Windows®
8 (32-/64-bit) / 7 (32-/64-bit) / Vista
(32-/64-bit) / XP (32-/64-bit) / Server 2003 & 2008
(32-/64-bit) / Server 2008 R2 / 2000 SP4
Mac®
:
• Power Mac®
G3 (blue & white) or later with an
available PCI slot
• Mac OS®
10.2.8 or later

2
Package Contents
•Hi-Speed USB 5-Port PCI
• Quick installation guide
Layout
Figure1:Layout
*Note: This power connector (same as the one
used with your floppy disk drive) is designed to
provide additional power to the board when
needed. Connect this power connector
(recommended) when one of the following
conditions occur:
- Device(s) not being detected
- All ports are used
Power off your system first before making this
connection.
External USB ports
Internal USB port
USB pin out header
Power Connector
(optional)*

3
GND
Data+
Data-
VCC/+5VDC
Black
Green
White
Red
USB Pin-out Header
The USB pin-out header consists of 4 pins and allows for
1 USB connection. USB pin-out header not available in
most Mac systems.
Important: The internal USB port and the USB Pin-out
Header can not be used at the same time. Do not connect
devices to both ports at the same time.
Figure 2: USB Pin-out Header
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer's reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer's case for a few
seconds. Avoid any contact with internal parts and handle
card only by their external edges.

4
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord and remove your computer
cover.
3. Remove the slot bracket from an available PCI slot.
4. Carefully align the card to the selected PCI slot,
push the board down firmly, but gently, until it is
well seated.
5. Replace the slot bracket's holding screw to secure
the card.
6. Replace the computer cover and reconnect the
power cord.
Driver Installation
The Hi-Speed USB 5-Port PCI has three built-in USB hosts.
Two hosts handle USB 1.1 devices and the third host
handles USB 2.0 devices. USB 1.1 and USB 2.0 devices are
automatically routed to the correct USB hosts.
Windows Driver Installation
Windows 8, 7, Vista, XP , Server 2003 & 2008, Server 2008
R2, and Windows 2000 have built-in driver support for
this controller. Just install the board and Windows will
automatically detect and install the correct drivers for it.
No additional driver is necessary.

5
To Verify Windows Installation
1. Use Device Manager to verify installation.
For Windows 8 / 7 / XP / 2003 / 2000: Right click
Computer or My Computer, click Manage, then
click Device Manager.
For Windows Vista: Right click Computer, click
Manage, click Continue, then Device Manager.
For Server 2008 / Server 2008 R2: Right click
Computer, clickManage.DoubleclickDiagnostics,
then click Device Manager.
2. Under Universal Serial Bus controllers:
-NEC PCI to USB Open Host Controller
- NEC PCI to USB Open Host Controller
- Standard Enhanced PCI to USB Host Controller
- USB Root Hub (USB 2.0 Root Hub in Win2K)
- USB Root Hub
- USB Root Hub

6
Mac OS X Driver Installation
MacOS X v10.2.8 orlater has built-in driversupportfor this
controller. Just install the board and Mac OS will
automatically detect and install the correct drivers for it.
No additional driver is necessary.
To Verify Mac OS Installation
Mac OS X (v10.2.8)
The only way to verify that the board works is to connect
devices to the USB ports.
Mac OS X (v10.3.0) or later
Check System Profiler to verify successfull installation.
Click Go, then Utilities. Double click on System Profiler
Under USB look for one or all of the following:
- USB High-Speed Bus
-USB Bus
- USB Bus

7
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at
www.siig.com and click Support. Our online support database is updated daily with
new drivers and solutions. Answers to your questions could be just a few clicks away.
You can also submit questions online and a technical support analyst will promptly
respond.
SIIG offers a lifetime manufacturer warranty with this product. This warranty covers
the original purchaser and guarantees the product to be free of any defects in materials
or workmanship for the life of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product
having similar features and functionality) the product if defective in materials or
workmanship. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Please see our web site for more warranty details.
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store
where you purchased from.
B) If your purchase has passed the store's return policy period, please follow the steps
below to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then REQUEST A PRODUCT
REPLACEMENT to submit a request to SIIG RMA or fax a request to 510-657-5962.
Your RMA request will be processed, if the product is determined to be defective,
an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All accessories that came with the
original package must be included.
• Clearly write your RMA number on the top of the returned package. SIIG will
refuse to accept any shipping package, and will not be responsible for a
product returned without an RMA number posted on the outside of the
shipping carton.
• You are responsible for the cost of shipping to SIIG. Ship the product to the
following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground in the U.S. and
International Economy outside of the U.S. at no cost to the customer.

PRODUCTNAME
Hi-Speed USB 5-Port PCI
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG,Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: [phone]
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebooksystems and external peripherals. SIIG continues togrowbyadding
A/V and Digital Signage connectivity solutions to our extensive portfolio.
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendlyfeatures,
and are backed by an extensive manufacturer warranty. High quality control
standards are evident by the overall ease of installation and compatibility of
our products, as well as one of the lowest defective return rates in the industry.
SIIG products can be found in computer retail stores, mail order catalogs,
throughmajor distributors, system integrators, andVARsin the Americas and
the UK, and through e-commerce sites.
Hi-Speed USB 5-Port PCI is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft
Corporation. All other names used in this publication are for identification only and may be
trademarks of their respective owners.
March, 2013 Copyright © 2013 by SIIG, Inc. All rights reserved.