SIIG CyberSerial Dual PCI User manual

1
CyberSerial Dual PCI
Quick Installation Guide
04-0375C
Introducing the CyberSerial Dual PCI
The CyberSerial Dual PCI high-speed serial I/O card
provides two additional 9-pin serial ports.
FeaturesandBenefits
•Conforms to PCI v2.2 Plug and Play
•Reduces CPU load and improves system
performance dramatically
•IRQ sharing feature reduces IRQ conflicts
•High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, label printers and other serial port
devices
•Built-in FIFO buffers dramatically increase data
transmit/receivespeed,especiallyunderWindows'
multitasking environment
•Each serial port can be configured for either 5V or
12V output, for serial devices that require power
SystemRequirements
•Pentium®or equivalent computer with an available
PCI slot
•Windows®7 (32-/64-bit) / Vista (32-/64-bit) / XP
(32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / 2000
/ NT 4.0 / ME / 98SE / 98 / 95; DOS
•Linux Kernel 2.4.x or later

2
PackageContents
•CyberSerial Dual PCI board
• Driver CD
• Quick installation guide
Layout
Figure 1. Layout
JumperSettings(JP1,JP2)
Open = 0 volts (default)
Short 1-2 = 5V
Short 2-3 = 12V
Note: Mostserialdevicesdonotrequireadditional
power through the serial port. Refer to your serial
device'smanualformoreinformation. The jumpers
can be removed if the serial ports aren't configured
for power output.
Serial Port 2
JP1 (Serial port 1)
JP2 (Serial port 2)
Serial Port 1

3
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the back of the
computer.
3. Remove your computer’s cover.
4. Remove the slot bracket from an available PCI slot.
5. Change JP1 and JP2 jumper settings to the desired
voltage only if your serial device needs additional
power from the serial port. However, most serial
devices do not require additional power. For more
information see Figure 1 on page 2.
6. To install the card, carefully align the card's bus
connector with the selected PCI slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.
7. Replace the slot bracket's holding screw to secure
the card.
8. Replacethecomputercover andreconnectthe power
cord.

4
Driver Installation
This section provides information on how to install the
CyberSerial Dual PCI drivers.
Windows7(32-/64-bit)
1. Right click Computer, click Manage, click Device
Manager.
2. Insert the driver CD. Right click PCI Serial Port,
click Update Driver Software.
3. Click Browse my computer for driver software.
4. Type D:, then click Next. (Change D: to match your
CD/DVD-ROM drive letter)
5. At Windows has successfully updated your driver
software, click Close.
6 Right click Other PCI Bridge Device, click Update
Driver Software.
7. Repeat steps 3-5.
8. Right click CyberSerial Communication Port, click
Update Driver Software.
9. Click Browse my computer for driver software.
10. Type D:, click Next. (Change D: to match your CD/
DVD-ROM drive letter)
11. At Windows has successfully updated your driver
software, click Close.
12. Repeat steps 8-11 to complete the installation.
WindowsVista™(32-/64-bit)
1. At the Found New Hardware window, insert the
driver CD, click Locate and install driver software
(recommended), then click Continue.
2. Click Next, then click Close.

5
3. Repeat step 2 to complete the driver installation.
Note: Windows Vista driver installation process
may take several minutes to complete.
WindowsXP(32-/64-bit)/Server2003(32-/64-bit)
1. At the Found New Hardware Wizard, insert the
driver CD.
2. Select No, not this time, click Next. (Skip this step
if not prompted)
3. Select Install the software automatically
(Recommended),then click Next.
4. Click Finish.
5. Repeat steps 1-4 two more times.
6. Restart Windows to complete the installation.
WindowsServer2008(32-/64-bit)
1. At the Found New Hardware Wizard, click Locate
and install driver software (recommended).
2. Insert the driver CD.
3. Click Don't search online.
4. Click I don't have the disc. Show me other options.
5. Click Browse my computer for driver software
(advanced).
6. Type D:, then click Next. (Change D: to match your
CD/DVD-ROM drive letter)
7. AtThe sofware for this device has been sucessfully
installed, click Close.
8. Repeat steps 3-7 to complete the installation.

6
Windows2000
1. At the Found New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended), then click Next.
3. Check Specify a location, uncheck the other boxes,
then click Next.
4. Insert the driver CD, type in D:\2000, then click OK.
(Change D: to match your CD-ROM drive letter)
5. Click Next and Finish.
6. Repeat steps 1-5 two more times.
7. Restart Windows to complete the installation.
To Verify Windows 7 / Vista / XP / Server 2003 &
2008/2000Installation
1. Check in Device Manager to verify installation.
For Windows 7: Right click Computer, click Manage,
then click Device Manager.
For Windows Vista: Right click Computer, click
Manage,click Continue,thenclickDevice Manager.
For XP / Server 2003 / 2000: Right click My Computer,
click Manage, then click Device Manager.
ForServer2008:RightclickComputer,clickManage,
double click Diagnostics, then click Device
Manager.
2. Click on the +(plus sign) in front of Ports (COM &
LPT), CyberSerial 16Cxxx... should be displayed
two times.
3. Double click Multifunction adapters, SIIG
CyberPro 2S board should be displayed.

7
WindowsME
1. At the Add New Hardware Wizard, select Specify
the location of the driver (Advanced),click Next.
2. Insert the driver CD, check Specify a location,
uncheck the other box, type in D:\ME,then click
Next.(Change D: to match your CD/DVD-ROM
drive letter)
3. Click Next, then Finish.
4. Repeat steps 1and 2.
5. Click Next, Next, then Finish.
6. Restart Windows to complete the installation.
Windows98/98SE
1. At the Add New Hardware Wizard, click Next.
2. Select Search for the best driver for your device
(Recommend), then click Next.
3. Insert the driver CD, check Specify a location,
uncheck the other boxes, type in D:\9x, then click
Next. (Change D: to match your CD/DVD-ROM
drive letter)
4. Click Next, then Finish.
5. Repeat steps 1-4.
6. Restart Windows to complete the installation.
Windows95
1. At the Update Device Driver Wizard, click Next.
2. Insert the driver CD, click Other Locations.
3. Type in D:\9x, click OK, then click Finish. (Change
D: to match your CD/DVD-ROM drive letter)

8
4. From the Insert Disk window, click OK. When the
Copying Files dialog box pops up, type in D:\9x,
then click OK. (Change D: to match your CD/DVD-
ROM drive letter)
5. Restart Windows to complete the installation.
To Verify Windows ME / 98SE / 98 / 95 Installation
1. Right click My Computer, click Properties,then
click Device Manager.
2. Double click Ports (COM & LPT), CyberSerial PCI
16Cxxx... should be displayed two times.
3. Double click Multi-function adapters, SIIG
CyberPro 2S... and PCI Function should be
displayed.
WindowsNT4.0
1. From the desktop click Start, then Run.
2. Insert the driver CD, type in
D:\NT4\Install_serial.exe, then click OK.
(Change D: to match your CD/DVD-ROM drive
letter)
3. Click Next when the Welcome window appears.
4. Select Install, then click Next.
5. Click Yes, then click Exit.
6. Restart Windows to complete the installation.
ToVerifyWindowsNT 4.0Installation
1. Click Start, Settings, Control Panel.Double click
Ports device icon.
2. Two new COM ports will be assigned when
successfully installed.

9
DOS
1. Boot up DOS and insert the driver CD.
2. Copy OXSER.EXE from the DOS folder to your C:
drive.
3. At the C: prompt, type in OXSER io=3e8 and the
serial ports will be set up as COM3 and COM4.
If your system already comes with 4 serial ports
enabled, type in OXSER io=220 instead and the
ports will be set up as COM5 and COM6.
4. Copy the OXSER command in step 3 into your
autoexec.bat and restart your system.
Linux Kernel 2.4.x or later
1. Open the terminal.
2. Type setserial -bg /dev/ttyS* and hit <enter> to
show the current serial ports installed. SIIG board
will be set up at the next available address. For
example, if your system comes with /dev/ttyS0
and /dev/ttyS1, set up SIIG board as /dev/tty2
and /dev/ttyS3.
3. Type lspci -v and hit <enter>. This command
displays the CyberSerial Dual PCI's information
similar to the example listed below. This
information is needed to configure the serial ports.
- 02:0b.0 Serial controller: Oxford Semiconductor
Ltd EXSYS EX-41092 Dual 16950 Serial ....
- Subsystem: SIIG Inc: ....
- Flags: medium devsel, IRQ 9
- I/O ports at a000 [size=32]
- Memory at ed800000 (32-bit, ...) ....
- I/O ports at 9800 [size=32]
- Memory at ed000000 (32-bit, ...) ....
- Capabilities: [40] Power Management ....

10
4. Edit the startup file and add these two command
lines at end of the startup file.
- setserial /dev/ttyS2 port 0xa000 irq 9 uart 16950.
- setserial /dev/ttyS3 port 0xa008 irq 9 uart 16950.
Note: ttyS value, I/O port address and irq should
be different from one system to another. These
values should be based on the results you get from
steps 2 & 3.
5. Save the startup file and restart your system.
Changing COM Port Address
Some serial devices need a specific COM port in order to
work. If your serial device works properly, do not
change this setting.
Windows 7 / Vista / XP / Server 2003 & 2008 / 2000
1. From the Device Manager window double click
Ports (COM & LPT), then double click the
CyberSerial serial port you want to change.
2. Click Settings tab and click Advanced.
3. Click the down arrow next to the COM Port number
box, select a COM port that is not in use. Click OK.
4. Click OK, then close Device Manager to save the
changes.
Windows ME / 98SE / 98 / 95
1. From the Device Manager window double click
Ports (COM & LPT), then double click the
CyberSerial PCI serial port you want to change.
2. Click Settings tab, click the down arrow next to Port
Name, select a COM address not currently in use.
3. Click OK, then close Device Manager to save the
changes.